To create or modify a Voice Codec Profile:

  1. In the WebUI, click the Settings tab.
  2. In the left navigation pane, go to Media > Media Profiles.
  3. From the Create Media Profile drop down box, select Voice Codec Profile.

Modifying a Voice Codec Profile

  1. Click the expand () Icon next to the entry you wish to modify.
  2. Edit the entry properties as required, see details below.

Creating a Voice Codec Profile

  1. From the Create Media Profile drop down box at the top of the Media Profiles page, select Voice Codec Profile.

  2. From the Codec drop down box, select a codec.

  3. Configure the files and click OK. See field definitions below.


    Create Voice Codec Profile

     

Voice Codec Profiles - Field Definitions


Configure Codecs

ParameterDescription
Description A user-defined name for the voice codec profile you create.
Codec

Specifies the voice codec and encoding scheme used towards the IP side of a VoIP call.

The selected codec affects the audio quality and bandwidth consumption of VoIP calls to which you apply the Voice Codec Profile (in the Media Profiles List). The codec choice depends on the interoperability requirements for connecting to other voice peers and bandwidth requirements. Most codecs use data compression algorithms, which saves bandwidth but slightly reduces the voice quality. G.711 does not use compression and requires more bandwidth.

The following codecs are supported on SBC Edge platform:

  • G.711 A-Law
  • G.711 u-Law
  • G.722
  • G.722.2
  • G.723.1
  • G.726
  • G.729
  • Opus
  • SILK

Codec - Additional Specifications

  • G.722 Wideband Codec: Supports 20ms packet sized and a bit-rate of 64Kbps only.
  • G.722 or AMR-WB channels: Does not support fax data detection support.
  • G.722.2: Appears only if the AMR License is installed.
  • G.726: Supports 32 Kbps bit rate only.
  • G.729: Supports G.729A and G.729AB. The variant used when selecting G.729 depends upon the setting of Media List flag Silence Suppression. If Silence Suppression is enabled, G.729AB is used.
  • Opus: Supported in SBC SWe Lite only.

NOTE: Applicable to the SBC SWe Lite initiating FAX setup. A G.711 codec must be used for fax detection; tones are detected on the G711 egress (answering CED tone) leg. Otherwise the peer has to initiate fax path.


Bandwidth

Specifies the bandwidth sampling frequency. This parameter has the following options:

  • Narrowband - The SBC Edge only uses the narrowband mode either to interface to PSTN networks, or on low-end devices that support 8000 Hz or less sampling frequency.
  • Wideband (default) - The SBC Edge uses the wideband mode for all IP platforms that support 16,000 Hz or less sampling frequency.

This parameter applies only to SILK.

Rate

Specifies the voice sampling rate in bits/sec used by the codec.

This parameter applies to G.722.2, G.723.1, G.729, Opus, and SILK codecs only. For all other codecs, the voice sampling rate is fixed and defined in the appropriate specification for that codec.

Payload Size

The recommended length of time in milliseconds rounded up to the next full integer value represented by the media in a packet. Valid entry: 10, 20, 30, 40, 60, 80, 90 (specific codec determines values available).

  • Smaller payload sizes decrease audio transport latency at the expense of higher bandwidth consumption.
  • Larger packet sizes reduce the bandwidth. The larger the payload size, the fewer and larger the packets. With larger payload sizes, fewer L2/Ethernet and IP/UDP/RTP headers are used; a disadvantage is that if UDP packets get lost, the impact on the voice quality is higher because a single packet contains more raw voice data.

SILK supports only the 20, 40, and 80 payload sizes.

For Re-Invite Only:

If the SBC receives a larger than configured payload size from the peer offer in the re-invite, the SBC rejects with a 488 'Not Acceptable Here' response. The call rolls back to the previous negotiated offer answer.

Payload Type

Specifies the payload type for this profile. Applies to G722.2, G.726, Opus, and SILK codecs only.

For SILK and Opus, the Payload Type option is 96 - 127. The default value is 120.

For SILK, the recommended default Payload Type values are: 103 (Narrowband) and 104 (Wideband).

Payload Format

Specifies the mode for the payload: Bandwidth Efficient Mode or Octet Aligned Mode. Default entry: Bandwidth Efficient Mode. This setting applies to G.722.2 only.

Voice Bit Rate

The maximum Opus bit rate (in bits/second) used for the current session. Valid entry: 0 (use variable bit rate) or 1 (use constant bit rate). Default entry: CBR.

Parameter applies to Opus only.

Use FEC

Specifies whether to use Forward Error Correction (FEC).

Valid entry for Opus: 0 (do not use FEC) or 1 (use FEC). Default entry for Opus: 0.

Valid entry for SILK: False (do not use FEC) or True (use FEC). Default entry for SILK: False.

Parameter applies to Opus and SILK only.

Use DTX

Specifies whether to use Discontinuous Transmission (DTX).

Valid entry for Opus: 0 (do not use DTX) or 1 (use DTX). Default entry for Opus: 0.

Valid entry for SILK: False (do not use DTX) or True (use DTX). Default entry for SILK: False.

Parameter applies to Opus and SILK only.

Complexity Level

Scales the complexity to optimize for CPU resources in real-time, which is mostly in trade-off to network bit rate.

For the SBC 1000/2000, the following options are available for this parameter: 0, 1, or 2. Default entry: 0.

For the SBC SWe Lite, the following option is available for this parameter: 0.

This parameter applies only to SILK.


Note

For more information about the SILK codec, refer to the following: