In this section:
Overview
The SBC SWe Lite includes the Easy Configuration option to add a partially configured signaling group with a new single end-point scenario for IP PBX.
The Configure Single Leg Endpoint for the IP PBX option applies to SBC SWe Lite only.
The SBC Easy Configuration interface includes a built-in, step-by-step setup configuration wizard to enable quick and easy deployment of a partially configured signaling group with a new single end-point scenario for an IP PBX.
For the single endpoint configuration, since the peer end if not known/configured, in the Easy Configuration Wizard, the Transformation and Routing entries for the endpoint being configured are created independent of the peer end. If you have two endpoints connected and use the Single Leg Wizard to add the third endpoint, you'll need to create/modify the Transformation and Routing entries to complete routing.
Easy Configuration Wizard - Single Leg Configuration Notes
- A single leg wizard should be used to add a 3rd, 4th, 5th peer to device, when at least 2 legs have already been configuring via the standard Easy Configuration Wizard.
- Emergency configuration is not supported for single end scenarios.
Step 1: Select IP PBX
Easy Configuration Step 1 includes configuration for scenario parameters.
- In the WebUI, click the Tasks tab.
- In the left navigation panel, go to SBC Easy Setup > Easy Config Wizard.
From the Application drop down list, select IP PBX.
Configure per the field definitions below and click Next.
Configure IP PBX
Configure Scenario Parameters - Field Definitions
Field Description Application Configuration template used: IP PBX. Scenario Description Name to describe the setup. Telephone Country Country in which the IP PBX is setup. SIP Sessions Number of simultaneous SIP Sessions. Valid entry: 1 - 960. Type IP PBX Type. Valid selections: - Avaya SM/CM
- Cisco CUCM
- Other IP PBX
Step 2: Configure IP PBX for Endpoint
Easy Configuration Step 2 includes configuration for the IP PBX endpoint.
- Configure the IP PBX information.
- Click Next.
Step 2 Example Screen
Avaya SM/CM
The fields below are displayed if you select Avaya SM/CM from the Type drop down list in Step 1.
Configure Avaya SM/CM
| Field | Description |
|---|---|
| Host | Host IP or FQDN. |
| Protocol | IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP. |
| Port Number | Port number used for sending and receiving SIP messages. |
| Use Secondary Server | Enables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled. |
| Secondary Server Host | Specifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled. |
| Protocol | The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled. |
| Port number | Specifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled. |
Cisco CUCM
The fields below are displayed if you select Cisco CUCM from the Type drop down list in Step 1.
Configure CISCO CUCM
| Field | Description |
|---|---|
| Host | Host IP or FQDN. |
| Protocol | IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP. |
| Port Number | Port number used for sending and receiving SIP messages. |
| Use Secondary Server | Enables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled. |
| Secondary Server Host | Specifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled. |
| Protocol | The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled. |
| Port number | Specifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled. |
Other IP PBX
The fields below are displayed if you select Other IP PBX from the Type drop down list in Step 1.
Configure Other IP PBX
| Field | Description |
|---|---|
| Host | Host IP or FQDN. |
| Protocol | IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP. |
| Port Number | Port number used for sending and receiving SIP messages. |
| Use Secondary Server | Enables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled. |
| Secondary Server Host | Specifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled. |
| Protocol | The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled. |
| Port number | Specifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled. |
Step 3: Summary
Easy Configuration Step 3 includes a summary of the information configured in Step 1 and Step 3.
Review the information and click Finish.
See below for an example:
Step 3 Example Screen
Overview
Content Tools