This page describes the procedure for installing new or additional Feature/Supplemental license keys.

 For steps on obtaining and installing licenses for SBC SWe Lite, refer to Obtaining and Installing a SWe Lite License.

 

To Install a License Key:

  1. In the WebUI, click the Settings tab.

  2. In the left navigation pane, go to System > Licensing > Install New License.

    Install New License

  3. Copy the license key from the email you received from Sonus.

  4. Paste the license key into the text box.Click Apply.

  5. Once the license is applied, the following message is displayed.

    Restart Message

  6. Click OK to reboot the system.


Sample License Key

WARNING

Do not attempt to use the sample key in your SBC Edge!

The license must contain the correct number of TDM ports in the system. An alarm is generated when the license key applied has more TDM ports licensed than are installed in the system, and the license key is rejected.

-----BEGIN LICENSE KEY-----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-----END LICENSE KEY-----
Note:

When copying the license text, be sure to copy the entire text shown above including the markers (e.g. ---BEGIN LICENSE KEY---).

 

Where to Find the Hardware and Software IDs

Viewing the Software Version and Hardware ID for SBC 1000/2000 and SBC SWe Lite

The SBC Edge software version and build number shown is the based on the firmware running on the active partition:

  1. In the WebUI, click the System tab.

  2. In the System page, click the Overview tab.

    For SBC 1000 only. The eUSB field identifies if the eUSB internal port is present: Yes (indicates the eUSB is present) or No (indicates the eUSB is not present).

    Example of the Overview Tab - SBC Edge

    Example of the Overview Tab - SBC SWe Lite