In this section:

Overview

The SBC SWe Edge includes the Easy Configuration option to add a partially configured signaling group with a new single end-point scenario for IP PBX.

The Configure Single Leg Endpoint for the IP PBX option applies to SBC SWe Edge only.

The SBC Easy Configuration interface includes a built-in, step-by-step setup configuration wizard to enable quick and easy deployment of a partially configured signaling group with a new single end-point scenario for an IP PBX. 

For the single endpoint configuration, since the peer end if not known/configured, in the Easy Configuration Wizard, the Transformation and Routing entries for the endpoint being configured are created independent of the peer end. If you have two endpoints connected and use the Single Leg Wizard to add the third endpoint, you'll need to create/modify the Transformation and Routing entries to complete routing.

Easy Configuration Wizard - Single Leg Configuration Notes
  • A single leg wizard should be used to add a 3rd, 4th, 5th peer to device, when at least 2 legs have already been configuring via the standard Easy Configuration Wizard.
  • Emergency configuration is not supported for single end scenarios.

Step 1: Select IP PBX

Easy Configuration Step 1 includes configuration for scenario parameters. 

  1. In the WebUI, click the Tasks tab.
  2. In the left navigation panel, go to SBC Easy Setup > Easy Config Wizard.
  3. From the Application drop down list, select IP PBX.

  4. Configure per the field definitions below and click Next.


    Configure Scenario Parameters - Field Definitions

    FieldDescription
    ApplicationConfiguration template used:  IP PBX.
    Scenario DescriptionName to describe the setup.
    Telephone CountryCountry in which the IP PBX is setup.
    SIP SessionsNumber of simultaneous SIP Sessions. Valid entry: 1 - 960.
    TypeIP PBX Type. Valid selections:
    • Avaya SM/CM
    • Cisco CUCM
    • Other IP PBX

Step 2: Configure IP PBX for Endpoint

Easy Configuration Step 2 includes configuration for the IP PBX endpoint.

  1. Configure the IP PBX information.
  2. Click Next.


Avaya SM/CM

The fields below are displayed if you select Avaya SM/CM from the Type drop down list in Step 1. 

Configure Avaya SM/CM

FieldDescription
HostHost IP or FQDN.
Protocol IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP.
Port NumberPort number used for sending and receiving SIP messages.
Use Secondary ServerEnables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled.
Secondary Server HostSpecifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled.
Protocol

The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled.

Port numberSpecifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled.

Cisco CUCM

The fields below are displayed if you select Cisco CUCM from the Type drop down list in Step 1. 

Configure CISCO CUCM

FieldDescription
HostHost IP or FQDN.
Protocol IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP.
Port NumberPort number used for sending and receiving SIP messages.
Use Secondary ServerEnables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled.
Secondary Server HostSpecifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled.
Protocol

The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled.

Port numberSpecifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled.

Other IP PBX

The fields below are displayed if you select Other IP PBX from the Type drop down list in Step 1. 

Configure Other IP PBX

FieldDescription
HostHost IP or FQDN.
Protocol IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP.
Port NumberPort number used for sending and receiving SIP messages.
Use Secondary ServerEnables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled.
Secondary Server HostSpecifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled.
Protocol

The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled.

Port numberSpecifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled.

Step 3: Summary

Easy Configuration Step 3 includes a summary of the information configured in Step 1 and Step 3.

Review the information and click Finish.

See below for an example: