In this section:
Overview
The SBC Easy Config interface includes a built-in, step-by-step configuration wizard that enables quick and easy set up of the SBC in a deployment that includes endpoints for an IP PBX and UCaaS.
The following SIP Trunks are supported:
- Cisco CUCM
- Other IP PBX
- Avaya SM/CM
Procedure
Step 1 - Select Scenario
- In the WebUI, click the Tasks tab.
- In the left navigation pane, go to SBC Easy Setup > Easy Config Wizard.
Select the Application (SIP Trunk ↔ IP PBX). Specify the configuration scenario details based on the deployment, then click Next to move to Step 2. (Or, you click Cancel if you need to return to the main WebUI screen.)
Configure Scenario - Field DefinitionsField
Description
Application IP PBX ↔ UCaaS Scenario Description Name to describe the setup. Telephone Country Country in which the IP PBX is setup. SIP Sessions Number of simultaneous SIP Sessions. Valid entry: 1 - 960. IP PBX IP PBX Type.
For SBC 1000/2000 and SBC SWe Edge:
- Avaya SM/CM
- Cisco CUCM
- Other IP PBX
UCaaS By default, the User Type is set to Zoom.
Step 2: Configure IP PBX
Easy Configuration Step 2 includes configuration for the IP PBX endpoint.
- Configure the IP PBX information (see below for field definitions for each available provider).
- Configure the UCaaS: Zoom information (see below for field definitions)
Click Next.
Avaya SM/CM
The fields below are displayed if you select Avaya SM/CM from the Type drop down list in Step 1.
Configure Avaya SM/CM
Field | Description |
---|---|
Host | Host IP or FQDN. |
Protocol | IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP. |
Port Number | Port number used for sending and receiving SIP messages. |
Use Secondary Server | Enables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled. |
Secondary Server Host | Specifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled. |
Protocol | The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled. |
Port number | Specifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled. Default entry: 5060. |
Cisco CUCM
The fields below are displayed if you select Cisco CUCM from the Type drop down list in Step 1.
Configure CISCO CUCM
Field | Description |
---|---|
Host | Host IP or FQDN. |
Protocol | IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP. |
Port Number | Port number used for sending and receiving SIP messages. Default entry: 5060. |
Use Secondary Server | Enables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled. |
Secondary Server Host | Specifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled. |
Protocol | The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled. |
Port number | Specifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled. |
Other IP PBX
The fields below are displayed if you select Other IP PBX from the Type drop down list in Step 1.
Configure Other IP PBX
Field | Description |
---|---|
Host | Host IP or FQDN. |
Protocol | IP protocol used for sending and receiving SIP messages between SBC and the server. Valid entries are UDP and TCP. |
Port Number | Port number used for sending and receiving SIP messages. Default entry: 5060. |
Use Secondary Server | Enables or disables the secondary Remote Peer service provider configured. Valid entry: Disabled or Enabled. |
Secondary Server Host | Specifies the Secondary host. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Server is Enabled. |
Protocol | The Protocol used for communicating with the Secondary Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Server is Enabled. |
Port number | Specifies the Port Number used for sending and receiving messages between the SBC and the Secondary Server. This field displays only when Use Secondary Server is Enabled. |
UCaaS: Zoom
Configure SIP Trunk: UCaaS Zoom
Field | Description |
---|---|
Signaling/Media Source IP | The external (Internet-facing) IP address of the Zoom server that handles routing of messages for signaling and media. |
Host | The IP/FQDN address used for Zoom. Valid entry: FQDN or IP. |
Port Number | The port used for Zoom. Valid entry: 1024 - 65535. |
Step 3: Confirm and Submit Configuration
This step displays a summary of the information configured in Step 1 and Step 2.
Review the information and click Finish.