In this section:
| Common Call Statistics Terminology | |
|---|---|
| Stable Calls | Calls that are established and fully stable (connected and media cut-through type of calls) and will survive a fail-over. This excludes calls in establishing, clearing and updating states which will not survive a fail-over. |
| Active Calls | A snapshot of total number of active calls on the SBC at the point of execution of the status command. This count reflects the actual live calls on the box independent of the state of the call (setup, stable, updating or clearing). |
| Call Attempts | Accumulative number of attempted calls on this system since the last reboot/start-up, including calls where a setup was sent/received, uncompleted calls (calls failed, busy, not answered, etc.) and calls completed (answered). |
| Call Completions | Accumulative number of calls completed on this system since the last reboot/start-up. |
The SBC allows the operator to access data from the current interval and from the interval statistics table related to each object being monitored. The current interval consists of a statistics table entry that is accumulating data for the next interval report. The interval statistics table is a series of statistics table entries containing data from the most recently completed n intervals (where n is the number of intervals in the retention policy configuration).
Note
Refer to Links to Statistics Pages to navigate to a particular EMA or CLI statistics page.
Note
If using the EMS in your network, configure EMS PM data collection intervals for the SBC to be both:
- Equal to or greater than the SBC intervals size, and
- Not less than the SBC interval size multiplied by the SBC number of intervals.
Refer to the Insight EMS User Guide for configuration details.
SBC intentionally does not display results of all calls when there is a high volume of traffic for the statistics below. This limitation is built into the SBC software to avoid excessive CPU usage and system timeouts.
- sipActiveGroupRegStatus
- sipActiveRegisterNameStatus
- sipDeletedRegisterNameStatus
- sipSigConnStatus
- sipSigTlsSessionStatus
Address Context
Command Syntax
> show status addressContext
cacOffenderStatus
callDetailStatusDetail
callMediaStatusDetail
callSummaryStatusDetail
diamNode
dnsGroup
dynamicBlackList
enhancedDBL
intercept
ipAccessControlList
ipInterfaceGroup
ipRouteStatus
ipsec
linkDetectionGroup
linkDetectionGroupStatistics
linkDetectionGroupStatus
logicalSigAddressBindingStatus
relayCurrentStatistics
relayIntervalStatistics
relaySessionStats
sipActiveGroupRegStatus
sipActiveGroupRegSummaryStatus
sipActiveRegisterNameStatus
sipDeletedRegStatus
sipDeletedRegisterNameStatus
sipGeneratedSubscriptionStatus
sipRegCountDomainCurStats
sipRegCountDomainIntStats
sipRegCountDomainStats
sipRegCountStatistics
sipSubCountStatistics
sipSubscriptionCountStatistics
sipSubscriptionStatus
surrRegCountStatistics
zone
zoneCurrentStatistics
zoneIntervalStatistics
zoneStatus
Command Parameters
Address Context Parameters
| Parameter | Description |
|---|---|
| This object displays recent SIP endpoint CAC offender details at the aggregate level (as opposed to the Address Context level) since the last system boot or restart. Go to Show Status Address Context - CAC Offender Status for details. |
| Call status details per address context. Go to Show Status Address Context - Call Status Details for details. |
| Call media status details per address context. Go to Show Table Address Context - Call Status Details for details. |
| Call summary details per address context. Go to Show Table Address Context - Call Status Details for details. |
| Diameter node configuration details. Go to Show Status Address Context - Diameter Node for details. |
| DNS Server Groups in this address context. Go to Show Status Address Context - DNS Group for details. |
| The collection of DBL policers. Go to Show Status Address Context - Dynamic Blacklist for details. |
| The enhanced DBL related operations. Go to Show Status Address Context - Enhanced DBL Status for details. |
intercept | Lawful Intercept Call Data Channel statistics details. Go to Show Status Address Context - Intercept for details. |
| IP Access Control list details for this address context. Go to Show Status Address Context - IP Access Control List for details. |
| IP Interface Group details for this address context. Go to Show Status Address Context - IP Interface Group for details. |
| IP route details including the local IP interfaces and protocols associated with the next hop routes. |
| IPsec configuration, security policy database, IKE peer table. |
| Link Detection Groups in this address context. |
| Statistics for link failure detected per link detection group. Go to Show Status Address Context - Link Detection Group
|
| The status of a link detection group. |
| The collection of logical signaling address bindings Go to Show Status Address Context - Logical Signal Address Binding Status |
| Relay count current statistics |
| Relay count interval statistics Go to Show Status Address Context - Relay Statistics
|
| Relay session statistics Go to Show Status Address Context - Relay Statistics
|
| This table presents the active SIP registration status for a list of SIP endpoints with unique id. |
| This table presents the active SIP registration status summary for a list of SIP endpoints. |
| This table presents the active SIP registration status for a list of SIP endpoints. |
| This table presents the deleted SIP registration status for a list of SIP endpoints with unique id. |
| This table presents the deleted SIP registration status for a list of SIP endpoints. |
| This table presents the active SIP subscription status for a list of SIP endpoints. |
| This table presents SIP registration count statistics for the SIP endpoints. |
sipRegCountDomainCurStats | This table presents per-domain SIP registration statistics for the current statistics interval. |
sipRegCountDomainIntStats | This table presents per-domain SIP registration interval statistics. |
sipRegCountDomainStats | This table presents registration statistics on a per domain basis. |
| This table presents SIP relayed subscription count statistics for the SIP endpoints |
| This table presents SIP subscription count statistics for the SIP endpoints. |
| This table presents the active SIP subscription status for a list of SIP endpoints. |
| This table presents Surrogate registration count statistics for the SIP endpoints. Go to Show Status Address Context - Surrogate Registration Count Statistics |
| Signaling, media, and control for a zone in the address context. |
| The Zone Statistics Current table. |
| The Zone Statistics Interval table. |
| The current status for zones in this address context. |
Command Examples
General Examples
To display the link Detection Group Status:
> show status addressContext default linkDetectionGroup
MGMT_LDG2 linkMonitorStatus MGMT_LM2
{
monitorStatus monitoring;
linkStatus up;
}
linkMonitorStatus MGMT_LM4
{
monitorStatus portDown;
linkStatus portDown;
}
linkMonitorStatistics MGMT_LM2
{
minTime 336;
maxTime 740;
averageTime 375;
singleFailures 0;
doubleFailures 0;
failures 0;
replies 13;
duplicateReplies 0;
lateReplies 0;
}
linkMonitorStatistics MGMT_LM4
{
minTime 0;
maxTime 0;
averageTime 0;
singleFailures 0;
doubleFailures 0;
failures 1;
replies 0;
duplicateReplies 0;
lateReplies 0;
}
To view default ACL statistics details:
> show status addressContext default ipAccessControlList defaultAclStatistics
defaultAclStatistics 9 {
protocol UDP;
application dns_udp_guest;
addressContextId *;
lifGrpId *;
sourceIpAddress "* (53)";
destinationIpAddress "* (0)";
policingMode PktRate;
bucketSize "50 pkt";
creditRate "1000 pkt/s";
polId 0;
polPriority 0;
packetAccept 0;
packetDiscard 0;
aggPol none;
owner vm;
vmGuestId Vm1;
}
Examples Showing Audio and Video Usage
Audio-Only CLI Output
admin@SBC01> show status addressContext default ipInterfaceGroup IG1
ipInterfaceStatus IF1 {
ifindex 13;
operState resAllocated;
oosReason notApplicable;
rxPackets 6488;
txPackets 140;
allocatedBandwidth 15800;
actualBandwidth 0;
bwDeviation 0;
numMediaStreams 1;
}
[ok][2014-07-17 16:47:26]
admin@SBC01> show status addressContext default ipInterfaceGroup IG2
ipInterfaceStatus IF2 {
ifindex 14;
operState resAllocated;
oosReason notApplicable;
rxPackets 270;
txPackets 2626;
allocatedBandwidth 15800;
actualBandwidth 0;
bwDeviation 0;
numMediaStreams 1;
}
[ok][2014-07-17 16:47:28]
admin@SBC01> show status addressContext default zone ZONE_IN_PCR1377 trunkGroupStatus
trunkGroupStatus TG_IN_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 1;
outboundCallsUsage 0;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 124;
bwOutboundUsage 0;
packetOutDetectState normal;
}
[ok][2014-07-17 16:47:36]
admin@SBC01> show status addressContext default zone ZONE_OUT_PCR1377 trunkGroupStatus
trunkGroupStatus TG_OUT_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 0;
outboundCallsUsage 1;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 0;
bwOutboundUsage 124;
packetOutDetectState normal;
}
Video-Only CLI Output
admin@SBC01> show status addressContext default ipInterfaceGroup IG2
ipInterfaceStatus IF2 {
ifindex 14;
operState resAllocated;
oosReason notApplicable;
rxPackets 236;
txPackets 1318;
allocatedBandwidth 128000;
actualBandwidth 21008;
bwDeviation 0;
numMediaStreams 1;
}
[ok][2014-07-17 16:33:21]
admin@SBC01> show status addressContext default ipInterfaceGroup IG1
ipInterfaceStatus IF1 {
ifindex 13;
operState resAllocated;
oosReason notApplicable;
rxPackets 5343;
txPackets 126;
allocatedBandwidth 128000;
actualBandwidth 23648;
bwDeviation 0;
numMediaStreams 1;
}
[ok][2014-07-17 16:33:25]
admin@SBC01> show status addressContext default zone ZONE_IN_PCR1377 trunkGroupStatus
trunkGroupStatus TG_IN_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 1;
outboundCallsUsage 0;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 1000;
bwOutboundUsage 0;
packetOutDetectState normal;
}
admin@SBC01> show status addressContext default zone ZONE_OUT_PCR1377 trunkGroupStatus
trunkGroupStatus TG_OUT_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 0;
outboundCallsUsage 1;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 0;
bwOutboundUsage 1000;
packetOutDetectState normal;
}
Both Audio and Video CLI Output
admin@SBC01> show status addressContext default ipInterfaceGroup IG1
ipInterfaceStatus IF1 {
ifindex 13;
operState resAllocated;
oosReason notApplicable;
rxPackets 6502;
txPackets 154;
allocatedBandwidth 143800;
actualBandwidth 0;
bwDeviation 0;
numMediaStreams 2;
}
[ok][2014-07-17 16:55:12]
admin@SBC01> show status addressContext default ipInterfaceGroup IG2
ipInterfaceStatus IF2 {
ifindex 14;
operState resAllocated;
oosReason notApplicable;
rxPackets 281;
txPackets 2635;
allocatedBandwidth 143800;
actualBandwidth 0;
bwDeviation 0;
numMediaStreams 2;
}
[ok][2014-07-17 16:55:19]
admin@SBC01> show status addressContext default zone ZONE_IN_PCR1377 trunkGroupStatus
trunkGroupStatus TG_IN_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 1;
outboundCallsUsage 0;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 1124;
bwOutboundUsage 0;
packetOutDetectState normal;
}
[ok][2014-07-17 16:55:31]
admin@SBC01> show status addressContext default zone ZONE_OUT_PCR1377 trunkGroupStatus
trunkGroupStatus TG_OUT_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 0;
outboundCallsUsage 1;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 0;
bwOutboundUsage 1124;
packetOutDetectState normal;
}
> show addressContext default sipActiveRegisterNameStatus
sipActiveRegisterNameStatus Ribbon@10.54.8.191 268 {
state completed;
contactURI sip:Ribbon@10.70.52.91:5070;
nextHopIpAddress 10.70.52.91;
nextHopPortNum 5070;
registrarIpAddress 10.128.254.86;
registrarPortNum 5090;
externalExpirationTime 3598;
internalExpirationTime 3600;
creationTime 2014-06-27T09:35:54+00:00;
registrarDomainName "";
endPointBehindNapt 0;
natPinholeLearningStatus none;
securityMechanismType none;
isRoaming 1;
}
To view SIP Peer CAC Status details:
show status addressContext addr_1 zone ZONE_IAD sipPeerCacStatus
sipPeerCacStatus "" 10.54.80.151 0 nonRegistrantSipPeer {
createdAt 2017-05-15T12:08:16+00:00;
ingressCallsAllowed 19;
ingressCallsActive 1;
ingressCallRejectsLimit 28;
ingressCallRejectsRate 0;
egressCallsAllowed 0;
egressCallsActive 0;
egressCallRejectsLimit 0;
egressCallRejectsRate 0;
state enabled;
ingressDblAggregateMessagesAllowed 0;
ingressDblAggregateMessageRejectsRate 0;
egressDblAggregateMessagesAllowed 0;
egressDblAggregateMessageRejectsRate 0;
ingressMessagesAllowed 0;
ingressMessageRejectsRate 0;
egressMessagesAllowed 0;
egressMessageRejectsRate 0;
ingressNotifysAllowed 0;
ingressNotifyRejectsRate 0;
egressNotifysAllowed 0;
egressNotifyRejectsRate 0;
ingressOptionsAllowed 0;
ingressOptionsRejectsRate 0;
egressOptionsAllowed 0;
egressOptionsRejectsRate 0;
ingressOtherRequestsAllowed 59;
ingressOtherRequestsRejectsRate 0;
egressOtherRequestsAllowed 0;
egressOtherRequestsRejectsRate 0;
ingressRefersAllowed 0;
ingressReferRejectsRate 0;
egressRefersAllowed 0;
egressReferRejectsRate 0;
ingressResponsesAllowed 0;
ingressResponseRejectsRate 0;
egressResponsesAllowed 0;
egressResponseRejectsRate 0;
ingressSubscribesAllowed 0;
ingressSubscribeRejectsRate 0;
egressSubscribesAllowed 0;
egressSubscribeRejectsRate 0;
bandwidthRejectsLimit 0;
videoThresholdLimit 0;
totalIngressHpcCallsAllowed 0;
rejectsMaxIngressHpcCallRate 0;
rejectsIngressMaxHpcCalls 0;
numActiveIngressHpcCalls 0;
totalEgressHpcCallsAllowed 0;
rejectsEgressMaxHpcCalls 0;
numActiveEgressHpcCalls 0;
}
Overview
Content Tools