In this section:
Use the NAT Traversal window to configure NAT traversal settings for SIP trunk groups. This section describes the various parameters associated with network-hosted NAT/NAPT traversal for SIP endpoints.
On the SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning > Trunk Group > SIP Trunk Group > Services > NAT Traversal. The NAT Traversal window displays.
Use the drop-down lists to select the desired Address Context, Zone and SIP Trunk Group. The Edit NAT Traversal window displays.
NAT Traversal
Use the following table to configure the NAT traversal settings for the trunk group and then click Save.
SIP Trunk Group - Services - NAT Traversal parameters
Parameter | Description |
---|---|
Signaling NAT | Indicates whether or not NAT/NAPT support is required for signaling.
|
Media NAT | Specifies whether or not NAT/NAPT support is required for media.
Note
Do not configure Media NAT and Ice Support flags on the same trunk group. Note
The SBC Core does not support NAT traversal for IPv6 calls. Ensure NAT is disabled in pure IPv6 call scenarios. |
Learn NAT For Rtp Only | Enable flag to learn media NAT from the first RTP packet only. If disabled, media NAT is learned from any first packet received. For egress trunk groups, this flag is applicable only if Dynamic LRBT flag is disabled. If Dynamic LRBT is enabled, NAPT learning occurs on arrival of RTP packet until the call is connected, at which point Learn NAT For Rtp Only applies even for egress Trunk Groups. The options are:
Note
The action of this flag does not apply to ICE NAT traversal. |
Ice Support | This parameter indicates the type of Interactive Connectivity Establishment (ICE) method used for STUN packet check. The values are:
Note
When configured for this mode, SBC acts as a generic ICE-Lite agent.
Note
For MS Lync ICE (Ice Lync setting), keep-alive messages are sent only to the RTP port. Note
Ribbon recommends to avoid configuring both Media Nat and ICE Support on the same Trunk Group because these configurations are independent mechanisms for solving NAT traversal issues. Because of of this, these configurations should not coexist on the same Trunk Group. Note
The parameter, Learn NAT For Rtp Only, does not apply to ICE and should not be enabled for the Trunk Group with ICE Support enabled. The SBC's ICE support capability is not supported for GW-GW call scenarios. Refer to SDP Support for a detailed description on Ice Support. |
Ice Keepalive Timer | Specifies the keep alive timer in full-ICE and MS-Lync ICE. The value ranges from 0 to 60 seconds and the default value is 15 seconds. Note
The Ice Keepalive Timer appears only when the Ice Support flag is set to Ice Full or Ice Lync. |
TCP Keepalive Timer | This NAT TCP keep-alive timer sets the registration refresh rate (in seconds) for SIP over TCP. (default = 240). |
Ice Trickle | Use this flag to enable Trickle Ice Support for the trunk group.
|
UDP Keepalive Timer | This NAT UDP keep-alive timer sets the registration refresh rate (in seconds) for SIP over UDP. (default = 60). |
Outbound Tcp Keepalive Timer | Specifies the NAT outbound keepalive timer (in seconds) for SIP over TCP. The value ranges from 0 to 32767 and the default value is 240. |
Outbound Udp Keepalive Timer | Specifies the NAT outbound keepalive timer (in seconds) for SIP over UDP. The value ranges from 0 to 32767and the default value is 60. |
Secure Media NAT Prefix | Use this parameter to match up to 'N' bits of the network IPv4 address obtained from signaling. If set to "0", feature is disabled, and no match of network IP address will occur. The value ranges from 0 to 32 and the default value is 0. |
Ice TCP Role | Use this flag to specify if SBC initiates the TCP connection for ICE Lync. The options are:
Note
Ice TCP Role appears only when the Ice Support flag is set to Ice Full or Ice Lync. Refer to Configuring SBC and LYNC in Media Environment for configuration details. |
Disable Media NAT If Same Media And Sig IP | Enable this flag to disable Media NAT if Media and Signaling IP addresses are identical. This setting is disabled by default. The options are:
|