In this section:
This object is used to configure the IP Access Control List rules.
The IP Access Control List Rule can only be created on a Default Address Context.
To View Rule
On the SBC main screen, go to Configuration > System Provisioning > Security Configuration > Ip Access Control List > Rule.
The Rule window displays.
To Edit a Rule
To edit any of the Rules in the list, click the radio button next to the specific Rule name.
For field descriptions, see Rule Parameters
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
To Create a Rule
To create a new Rule, click New Rule tab on the Rule List panel.
The Create New Rule window is displayed.
Rule Parameters
Parameter | Description |
|---|---|
Name | The name of this access control list rule. |
Precedence | Use this parameter to specify the rule precedence to control which ACL rule is applied when multiple rules match a given packet. If an incoming packet matches multiple rules, the IP ACL rule with the highest precedence (lowest numerical precedence value) is applied to that packet. Each IP ACL rule must use a unique precedence value. |
Protocol | Enter IP protocol type for use as a criterion of the IP input match. Choices are 0-255, or one of the following:
These protocols are typically associated with particular logical port values. |
IP Interface | The name of a IP interface group to match or "any" to match any IP interface group. |
IP Interface | The name of an IP interface to match, or "any" to match any IP interface. |
Mgmt IP Interface Group | The name of a Management Interface Group. NOTE: The |
Mgmt IP Interface | The name of a Management IP Interface. NOTE: The |
Source IP Address | The source IP address to match. When configuring a Source Ip Address, you must also specify Source Address Prefix Length. |
Source Address | The length of source IP address prefix which must match the protocol. Range: 0 - 32, default is 0 |
Destination IP Address | The destination IP address (IPV4/IPV6) prefix to match. When configuring a Destination Ip Address, you must also specify the Destination Address Prefix Length. |
| Destination Address Prefix Length | Specify the length of destination IP address prefix. Range: 0 to 128, default is 0. |
Source Port | The IP port value. Must be 0 - 65535, default is any. |
Destination | The IP port value. Must be 0 - 65535, default is any. |
Action | The action to be taken when the IP access control list rule match.
|
Fill Rate | The number of packets to add to the bucket credit balance (in packets/second). If a packet is received at a rate exceeding this fill rate, it is discarded subjected to the discard rate set in the IP Policing Alarm profile or in the Policer Alarm monitoring this Media Port. The bucket credit balance is always less than the configured bucket size regardless of the size of this increment. Range: 1 - 10000, default is 50 |
Bucket Size | The policing bucket size (in packets). It represents a credit balance that should be consumed before the packets are discarded. The consumed credits reside in the bucket and gets reduced for every packet received on the Network Interface (NI). If a packet is received when the credit balance is less than the size of the packet, the packet is discarded subjected to the discard rate set in the IP Policing Alarm profile or in the Policer Alarm monitoring this Media Port. (default is 'unlimited', which allows continuous policing). Range: 1 - 255, default is 50 |
State | It specifies the administrative state of ACL rule.
|
| Vm App Name | Specify the name of the Virtual Machine application used. |
| Aggregate Policer | Specify the name of aggregate policer with which this rule is associated. |
To Copy a Rule
To copy any of the created Rule and to make any minor changes, click the radio button next to the specific Rule to highlight the row.
Click Copy Rule tab on the Rule List panel.
The Copy Selected Rule window is displayed along with the field details which can be edited.
Make the required changes to the required fields and click Save to save the changes. The copied Rule is displayed at the bottom of the original Rule in the Rule List panel.
To Delete a Rule
To delete any of the created Rule, click the radio button next to the specific Rule which you want to delete.
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
Click Yes to remove the specific Rule from the list.
Overview
Content Tools