In this section:

Use this object to create a template for the ISUP signaling services that will be used by the ISUP service group that uses this signaling profile.

To View ISUP Signaling Profiles

On the SBC main screen, go to Configuration > Profile Management > Category: Signaling Profiles > ISUP Signaling Profile.

The ISUP Signaling Profile window is displayed.

To Create an ISUP Signaling Profile

To create a new ISUP Signaling Profile, click New ISUP Signaling Profile on the ISUP Signaling Profile List window.

The Create New ISUP Signaling Profile window is displayed.

 


Parameter

Description

Name

The name of the ISUP signaling group you are configuring. This name must match the strings to be used in the version field of the SIP message header.

Version Id

The version ID to identify a signaling group. Enter a value in the range of
(100..65535).

Note:

Version IDs from 0-99 are reserved

Base Profile

May be specified when configuring a named ISUP signaling profile. The specified base profile is used as a set of defaults for all profile parameter values. Then any parameter for which you explicitly specify a value overrides the default base profile value, in the resulting named signaling profile.

OLIP Check

Specifies whether or not to support check for the presence of an OLIP when determining that a call is invalid.

The options are:

  • Un Supported (default)
  • Supported

Hop Count
Value

The initial Hop Counter value to use (if Hop Count State is enabled). Must be 10-20.

Hop Count
State

The state of Hop Counting procedures for this service group:

  • Un Supported - (default) The procedures are in effect. This state requires that the ISUP protocol revision be ANSI1992 or ANSI1995.
  • Supported - The procedures are not in effect.

When Hop Count State is enabled, the following applies:

  • If a Hop Counter parameter is received from the ingress leg of the call, it is decremented and included in the outgoing IAM message. If no Hop Counter is present in the ingress leg of the call, it is included in the outgoing IAM message using Hop Count Value.
  • If a Hop Counter of zero is present in the ingress leg of the call, the call is released with a cause of "exchange routing error".

When Hop Count State is disabled, the following applies:

  • If a Hop Counter parameter is received from the ingress leg of the call, it is passed transparently in the outgoing IAM message.
  • If a Hop Counter of value zero is present in the ingress leg of the call, the call is released with a cause of "exchange routing error".

Base Version

Specifies the version of the Base Signaling group from rfc3204. The possible values are:

  • Ansi00
  • Ansi88
  • Etsi121
  • Etsi356
  • Gr317
  • Itut-88
  • Itu-t92+
  • None
  • Ttc87
  • Ttc93+

Revision

The ISUP protocol revision that will be supported for this ISUP service:

  • Ansi1992 - Use this protocol if this ISUP service is connecting DMS and ESS SWITCHTYPEs.
  • Ansi1995
  • Itu1993
  • Etsi2 - Use for Germany and Netherlands. (For Germany, use the Default_German ISUP signaling profile; for Netherlands, use the Default_ETSI_V2 ISUP signaling profile.)
  • Nttfcc - Use for Japan.
  • Itu1997
  • Itu1988
  • Ituq767 - Same as etsii (has been renamed).
  • Belgacom
  • Spirou
  • Mexicoic
  • Italy
  • Denmarkic
  • Hongkongic
  • Singapore
  • Etsi3
  • Peru
  • Chile
  • Portugaloni
  • Nttcom - Use the NTT Communications protocol for Japan.
  • Chinacnc
  • Spain
  • Argentinaidt
  • Argentina
  • Brazil
  • India
  • Korea
  • Ukisup
  • Etsi2plus - Use for Malaysia.
  • Ansiatt
  • Israel
  • Slovak2 - Use for Slovakia
  • Russia

OLIP Check on
Send

When a call with a Charge Number and a Calling Party Number arrives, by default the SBC checks for Originating Line Information Parameters (OLIP) and rejects the call if they are not present. This parameter turns OLIP checking off for certain switches that do not supply OLIP information to such calls:
• unsupported—check for OLIP
• supported —don't check for OLIP

This check is applied only when the SBC receives an IAM.

Network
Indicator

Specifies whether the network indicator functionality is active.

Propogation
Delay Support

Specifies whether the propagation delay functionality is active:

  • Un Supported (default)
  • Supported  

Look Ahead for
Busy

Specifies the default value used in the Look Ahead for Busy field in the ISUP Precedence parameter.
• allowed—Look Ahead for Busy is allowed.
• path reserved—Look Ahead for Busy path is reserved.
• not allowed (default)—Look Ahead for Busy is not allowed.

Network
Identity

Specifies the default value used for the 4-digit network identity field in the ISUP Precedence parameter. Must be 0000-9999; default is 0100.

Generate Japan
Ics Params

Specifies whether to support generating ICS information in SIP MIME case for the signalling group.

Compatibility

Specifies whether the compatibility is supported for the ISUP Signaling profile

Access
Delivery

Specifies whether the access delivery information is active.

Generic Number

Specifies whether the generic number functionality is active:

  • Un Supported (default)
  • Supported  

Generic
Notification

Specifies whether the generic notification functionality is active:

  • Un Supported (default)
  • Supported  

Generic Digits

Specifies whether the generic digit functionality is active:

  • Un Supported (default)
  • Supported  

Location
Number

Specifies whether the location number functionality is active:

  • Un Supported (default)
  • Supported  

Originating
ISC Point Code

Specifies whether the originating ISC point code functionality is active:

  • Un Supported  (default)
  • Supported  

User Tele
Service

Specifies whether the user teleservice functionality is active:

  • Un Supported (default)
  • Supported  

Segmentation

Specifies whether the segmentation functionality is active:

  • Un Supported (default)
  • Supported

Fallback

Specifies whether the fallback functionality is active:

  • Un Supported (default)
  • Supported

E MCID

Specifies whether the EMCID functionality is active:

  • Un Supported (default)
  • Supported  

Subscriber
Priority Class

Specifies whether the subscriber priority class functionality is active:

  • Un Supported (default)
  • Supported    

APM

Specifies whether the APM is supported for the ISUP Signaling profile.

  • Un Supported (default)
  • Supported    

Connected
Number in ACM

Specifies if the connected number parameter is supported in the ACM for the ISUP Signaling profile.

Cause In CPG

Indicates that the cause parameter supported in the CPG for the ISUP Signaling profile.

Multi Carrier
Environment

Specifies whether the multi carrier environment functionality is active.

Carrier
Selection

Indicates that the carrier selection is supported for the ISUP Signaling profile.

Inr Inf

Specifies whether INR/INF messages are supported.

CQM CQR

Specifies if the CQM/CQR is supported for the ISUP Signaling profile.

Call Reference

Indicates that the call reference parameter is supported for the ISUP Signaling profile.

CFN

Indicates that the CFN is supported for the ISUP Signaling profile.

Facility

Specifies whether the FAA, FAR, and FRJ messages are supported.

PAM

Specifies whether the PAM message is supported.

OBCI ANM

Specifies whether the optional backward call indicators parameter is supported in the
ANM message.

DRS

Specifies whether the DRS message is supported.

Redirection
Number

Specifies whether the redirection number parameter is supported.

LPA

Specifies whether the LPA message is supported.

UCIC

Specifies whether the UCIC message is supported.

OLM

Specifies whether the OLM message is supported.

Blue Book In
Rel

Specifies whether the Blue Book parameters are supported in REL for the ISUP Signaling Profile.

USR

Specifies whether the Blue Book specific parameters are supported in the USR
message

BB IAM

Specifies whether the User-To-User indicator parameter is supported in IAM for the
ISUP Signaling Profile.

Call Mod Msgs

Specifies that the CMR, CMA and CMRJ are the call mod messages supported for the ISUP Signaling profile.

Call Diversion

Specifies whether the call diversion is supported for the ISUP Signaling profile.

Call History

Specifies whether the call history parameter is supported for the ISUP Signaling profile.

Generic
Reference

Specifies whether the generic reference parameter is supported

MLPP

Specifies whether the MLPP parameter is supported.

NSF

Specifies whether the network specific functionality parameter is supported.

Redirection Number Restriction

Specifies whether the redirection number restriction parameter is supported in ANM, ACM, CPG, and CON messages

Remote
Operations

Specifies whether the remote operations parameter is supported.

Service
Activation

Specifies whether the service activation parameter is supported.

Signaling
Point Code

Specifies whether the signaling point code parameter is supported.

TMR Prime

Specifies whether the transmission medium required prime parameter is supported.

Transmission
Medium Used

Specifies whether the transmission medium used parameter is supported.

USI Prime

Specifies whether the user service information prime parameter is supported.

Redirection
Number in ACM

Is the redirection number supported in the ACM for the ISUP Signaling Profile.

Redirection
Number in ANM

Is the redirection number supported in the ANM for the ISUP Signaling Profile.

Connection Req in FAA

Specifies whether the connection request parameter is supported in the FAA for the
ISUP Signaling profile.

Connection Req in FAR

Specifies whether the connection request parameter is supported in the FAR for the
ISUP Signaling profile.

FAC

Specifies whether the FAC message is supported

Echo Control

Specifies whether the echo control parameter is support.

Backward GVNS

Specifies whether the backward GVNS parameter is supported for the ISUP Signaling Profile.

Circuit
Assignment Map

Specifies whether the circuit assignment map parameter is supported for the ISUP Signaling profile.

CCSS

Indicates that the CCSS parameter supported for the ISUP Signaling profile.

Call Diversion
Treatment

Specifies whether the call diversion treatment parameter is supported for the ISUP Signaling profile.

Called In Num

Indicates that the called IN number parameter supported for the ISUP Signaling profile.

Collect Call
Req

Specifies that the collect call request parameter is supported for the ISUP Signaling profile.

Conference
Treatment

Specifies whether the conference treatment parameter is supported for the ISUP Signaling profile.

Correlation Id

Specifies whether the correlation ID parameter supported for the ISUP Signaling profile.

Call Offering
Treatment

Indicates that the call offering treatment parameter is supported for the ISUP Signaling profile.

Call Transfer
Number

Indicates that the call transfer number parameter is supported for the ISUP Signaling profile.

Call Transfer reference

Indicates that the call transfer reference parameter is supported for the ISUP Signaling profile.

Display Information

Indicates that the display information parameter is supported for the ISUP Signaling profile.

Forward GVNS

Specifies whether the forward GVNS parameter is supported.

Loop
Prevention

Specifies whether the LOP message and the Loop Prevention indicators parameter is supported.

Network
Management

Specifies whether the Network Management Control parameter is supported.

SCF Id

Specifies whether the SCF ID parameter is supported.

UID Action IND

Specifies whether the UID action indicators parameter is supported.

Uid Capability
Ind

Specifies the UID capabilities parameter supported for the ISUP Signaling Profile.

Connected
Number In Cpg

Specifies the connected number parameter supported in the CPG for the ISUP Signaling
Profile.

Generic Number
In Cpg

Specifies the generic number parameter supported in the CPG for the ISUP Signaling Profile.

Echo Control
In Iam

Specifies the echo control parameter supported in the IAM for the ISUP Signaling
Profile.

Remote Operation In Rel

Specifies the remote operations parameter supported in the REL for the ISUP Signaling Profile.

Access Transport In Fac

Specifies the access transport parameter supported in the FAC for the ISUP Signaling Profile.

Generic Notification In Fa

Specifies the generic notification parameter supported for the ISUP Signaling Profile.

Uuind Anm

Specifies the UUI parameter supported in the ANM for the ISUP Signaling Profile.

Uuind Cpg

Specifies the UUI parameter supported in the CPG for the ISUP Signaling Profile.

Nrm Support

Specifies the NRM supported for the ISUP Signaling Profile.

Cause In Rlc

Specifies the cause parameter supported in the RLC for the ISUP Signaling Profile.

Upa Upt

Specifies the UPA/UPT supported for the ISUP Signaling Profile.

Recommendation
In Cai

Specifies the recommendation field supported in the cause parameter for the ISUP Signaling Profile.

Transit
Unrecognized

Specifies the transiting of unrecognized parameters supported for the ISUP service
Group.

U2u Service
Level

Specifies the level of user to user services supported in the ISUP Signaling Profile.

Subsequent Address Message

Specifies the Subsequent Address Message supported for the ISUP Signaling
Profile.

Forward Transfer Message

Specifies the Forward Transfer Message supported for the ISUP Signaling Profile.

Special Digits

Specifies the special digits which can appear in dialed digit strings

• digitA - BIT 0 - Is digit A allowed in the digit string
• digitB - BIT 1 - Is digit B allowed in the digit string(default)
• digitC - BIT 2 - Is digit C allowed in the digit string(default)
• digitD - BIT 3 - Is digit D allowed in the digit string
• digitE - BIT 4 - Is digit E allowed in the digit string
• digitF - BIT 5 - Is digit F allowed in the digit string(default)
• none - BIT 6 - No special digits in the digit string

Transit Network Selection

Specifies the Transit Network Selection Parameter supported for the ISUP Signaling
Profile.

Access
Transport

Specifies the Access Transport parameter supported for the ISUP Signaling Profile.

Jurisdiction

Specifies the Jurisdiction parameter supported for the ISUP Signaling Profile.

Original Called Number

Specifies the Original Called Number parameter supported for the ISUP Signaling Profile.

Business Group

Specifies the Business Group parameter supported for the ISUP Signaling Profile.

Connection Req

Specifies the Connection Request parameter supported for the ISUP Signaling Profile.

Information Ind

Specifies the Information Indicator parameter supported for the ISUP Signaling Profile.

Network Transport

Specifies the Network Transport supported for the ISUP Signaling Profile.

Notification Ind

Specifies the Notification Indicator parameter supported for the ISUP Signaling Profile.

Redirection Info Acm

Specifies the Redirection Information parameter supported in the ACM message for the ISUP Signaling Profile.

Egress Service

Specifies the Egress Service parameter supported for the ISUP Signaling Profile.

Service Code Ind

Specifies the Service Code Indicator parameter supported for the ISUP Signaling Profile.

Special Process Req

Specifies the Special Processing Request parameter supported for the ISUP Signaling Profile.

Charge Number

Specifies the Charge Number parameter supported for the ISUP Signaling Profile.

Transaction Req

Specifies the Transaction Request parameter supported for the ISUP Signaling
Profile.

Generic Address Rel

Specifies the Generic Address parameter supported in the REL message for the
ISUP Signaling Profile.

Uu Ind Acm

Specifies the User to User Indicators parameter supported for the ISUP Signaling
Profile.

Uu Info

Specifies the User to User Information parameter supported for the ISUP Signaling
Profile.

Operator
Service Info

Specifies the Operator Service Information parameter supported for the ISUP Signaling Profile.

Cvt Cvr

Specifies the Circuit Validation Test/Response procedures supported for the ISUP Signaling Profile.

Generic Name

Specifies the Generic Name parameter supported for the ISUP Signaling Profile.

Redirection
Cap

Specifies the Redirection Capability parameter supported for the ISUP Signaling
Profile.

Group Redirection Count

Specifies the Group Redirection Count parameter supported for the ISUP Signaling
Profile.

Send Two Group Msgs

Sets the Flag to Send Two Group Messages in the ISUP Signaling Profile.

Await Two Group Msgs

Sets the Flag to Await Two Group Messages in the ISUP Signaling Profile.

Cqm On Card Swap

Sets the Flag to perform CQM on Card Swap in the ISUP Signaling Profile.

Ansi95Grs

Specifies the ANSI-95 format for Group Reset Circuit (GRS), which includes optional/ parameters to be used.

Cpg Before Acm

Specifies a CPG arriving before an ACM be transited.

Map Dms Fe Parameter

Specifies if the service group should perform mapping of the Completion Code in the DMS FE parameter (ANSI ISUP only)

Trunk Offering Support

Specifies if the trunk offering messages can, fan, ofr, rcl are supported, at the moment this is just for mexico.

Operator Selection

Specifies if the operator selection parameter is supported.

Max Calling Party Digits

Specifies the maximum digit string length for the Calling Party Number parameter supported for this ISUP Signalling Profile.

Max Called Party Digits

Specifies the maximum digit string length for the Called Party Number parameter supported for this ISUP Signalling Profile

Free Phone Ind

Specifies the Freephone Indicators parameter supported for this ISUP Signalling Profile.

Itx Txa

Specifies the ITX and TXA messages supported for the ISUP Signaling Profile.

Sccp Procedure

Specifies the SCCP Procedure supported for the ISUP Signaling Profile.

Connection Req In Iam

Specifies the Connection Request parameter supported in the IAM for the ISUP Signaling Profile.

Ccnr

Specifies the CCNR Possible Indicator parameter supported for the ISUP Signaling Profile.

Transit Cfn

Specifies the CFN message be transmitted for the ISUP Signaling Profile.

Holding Ind

Specifies the Holding Indicator be supported for the ISUP Signaling Profile.

Display Info In Acm

Displays Information parameter in the ACM be supported for the ISUP Signaling Profile

IAM Generated Carrier Code In Cdr

Should the IAM-Generated Carrier Code always be populated in the CDR for Japan regardless of type.

Cit Term Exchange Logic

CIT and CAI only in first backward message when terminating exchange

Check Ixc Against Tlec

• PROTOCOLS - JAPAN
• DEFAULT- UNSUPPORTED
• UNSUPPORTED - Modify received CIT parameter as usual
• SUPPORTED - Transit received CIT parameter unchanged
• CMD- TRANSITRCVDCIT
• SCREEN- Services - Transit Received CIT
• CONTROL- SS7_CONTROL_TRANSIT_RECEIVED_CIT
• REQS- SBTM - PCR1499

Unique Transit Cit

• PROTOCOLS - JAPAN
• DEFAULT- UNSUPPORTED
• UNSUPPORTED - Modify received CIT parameter as usual
• SUPPORTED - Transit received CIT parameter unchanged
• CMD- TRANSITRCVDCIT
• SCREEN- Services - Transit Received CIT
• CONTROL- SS7_CONTROL_TRANSIT_RECEIVED_CIT
• REQS- SBTM - PCR1499

Transit Received Cit

• PROTOCOLS - JAPAN
• DEFAULT- UNSUPPORTED
• UNSUPPORTED - Modify received CIT parameter as usual
• SUPPORTED - Transit received CIT parameter unchanged
• CMD- TRANSITRCVDCIT
• SCREEN- Services - Transit Received CIT
• CONTROL- SS7_CONTROL_TRANSIT_RECEIVED_CIT
• REQS- SBTM - PCR1499

Allow SGDin Generic Digits

Specifies whether SGD parameter (Generic Digits type 25) in mime of SIP-I message is supported or not. The options are:

  • Un Supported (default)
  • Supported 
Note:

If the SGD parameter in the SIP-I mime is to be processed or sent, the Generic Digits needs to be supported as well.

Note:

This flag is not applicable when the SBC is configured for ERE mode.

Set Bci Cdps Based On Sip Call Status

Set this flag to "supported" to modify the called party's status indicator in BCI parameter of MIME data as per the SIP status. If 183 Session Progress is carrying a MIME of called party's status indicator in BCI with a value OTHER THAN "No indication", then it is updated to a value "No indication". Similarly, if 180 Ringing is carrying a MIME of called party's status indicator in BCI with a value OTHER THAN "Subscriber Free", then it is updated to a value "Subscriber Free".

The options are:

  • Un Supported (default)
  • Supported
Send PRIon RELfor CBWF

Use this flag to send either APM or PRI message with Call Back When Free (CBWF) information on the SIP-I (UK-ISUP) leg during tear down of CBWF call.

The options are:

  • Supported: Send PRI message 
  • Un Supported (default): Send APM message
Note:

The flag Send PRIon RELfor CBWF applies to SIP-I (UK-ISUP variant) only.


Send APPin APMfor CBWF

Use this flag to send CBWF-related APP (ACI=126) in a new APM message. If set to "unsupported" , APP is sent in the regular signaling message (e.g. ACM instead of APM).

The options are:

  • Supported: When this option is selected, only APM messages are sent with APP information.
  • Un Supported (default): When this option is selected, the APP parameter is sent in regular signaling messages. For example, ACM instead of APM.
Note:

The flag Send APPin APMfor CBWF applies to SIP-I (UK-ISUP variant) only.


Gr317Charge Number Compliance

Use this flag to check the charge number digit length is in compliance with GR317 which specifies a maximum of 10 digits in IAM message. The Gr317Charge Number Compliance flag does not affect the charge number header contents in SIP messages. When the egress trunk group has the Isup Mime Body Relay flag enabled, any charge number parameter received in the ingress ISUP MIME is sent in the egress ISUP MIME irrespective of the value of Gr317Charge Number Compliance setting.

  • UnSupported (default) – SBC does not check charge number digit length for GR317 compliance.
  • Supported – SBC checks charge number digit length for GR317 compliance, and does not send message if digit length is greater than 10 digits. If digit length is 11 or more digits, the charge number parameter is discarded and a MINOR log message is logged to the debug log.
Note:

This flag can only be set to Supported for ANSI ISUP variant. Additionally, the Gr317Charge Number Compliance check only applies to the ISUP MIME sent by the SBC; it does not apply to the ISUP MIME received by the SBC.

Charge Rate Info For CPC Apc

Use this flag to determine whether the SBC checks for specific payphone-related characteristics in J-ISUP to non-Japanese ISUP calls to trigger using different charge rate information (CRI). The options are:

  • Supported
  • Un Supported (default)

If set to Supported, the SBC checks for the following conditions:

  • The ingress leg of the call must be a J-ISUP variant
  • The egress leg of the call must be a non-Japanese ISUP variant
  • The call request must include one of the following:
    • The CPC (Calling Party's Category) value in the incoming INVITE/IAM message has the value "pay phone"
    • The APC (Additional Party Category) value in the incoming INVITE/IAM message has the value "Pink" (00000010) or "train pay phone"(00000001).

If a call meets the conditions, the SBC takes charge rate information (CRI) taken from the PSX Charge Rate Profile table specified in the PSX Charge Band Profile associated with the call's ingress trunk group. The CRI is returned in the first backward Address Complete Message (ACM), Call Progress (CPG), or Charging Information (CHG) message during call setup.

If the option is set to Supported but the conditions are not met or Charge Rate Profile table data is not available, no charge information is returned in the ACM, CPG, or CHG messages.

If the option is set to Un Supported, the SBC takes CRI values from the PSX Charge Rate Information Parameter table for J-ISUP to non-Japanese ISUP calls and sends them in the first backward ACM, CPG, or CHG message during call setup.

Note:

The Charge Rate Info For CPC Apc option is only configurable on Japan-based ISUP Signaling Profiles in which the Revision value specifies either the Nttfcc or Nttcom ISUP variant.

Cpg Release Timer

Use this timer to specify a time, in seconds, after which the SBC releases a call that has had ANM to CPG message conversion applied. The timer can be set up to 300 seconds. The default is 0.

Note:
Values greater than 0 can be configured only on JAPAN-based profiles in which the Revision value specifies either the Nttfcc or Nttcom ISUP variant. 

To Edit an ISUP Signaling Profile

  1. To edit an ISUP Signaling Profile in the list, select the profile from the ISUP Signaling Profile List by clicking the radio button next to it. The Edit Selected ISUP Signaling Profile window is displayed.
  2. Make necessary changes and click Save to save the changes. 

To Copy an ISUP Signaling Profile

  1. To copy an ISUP Signaling Profile object, select the profile from the ISUP Signaling Profile List window by clicking the radio button next to it.
  2. Click Copy ISUP Signaling Profile on the ISUP Signaling Profile List window. The Copy Selected ISUP Signaling Profile window is displayed.
  3. Make necessary changes and click Save to save the changes. Click Undo Edits to cancel all changes.

To Delete an ISUP Signaling Profile

  1. To delete an ISUP Signaling Profile object, click the X symbol at the right of the row containing the profile name that you want to delete. A dialog box pops up, asking for confirmation of the deletion.
  2. Click Yes to confirm the deletion when prompted. 
  3. Click Ok to complete the deletion process.