In this section:
ENUM ARS Profile
Use this section to configure an ENUM ARS Profile for ENUM servers, and to specify behavior for managing device failover to a secondary or backup ENUM server in the form of blacklisting and whitelisting parameters.
Command Synax
% set global servers enumArsProfile <enumArsProfile name> blackListing duration <0-99999> numberOfFailures <1-32> whiteListing highWaterMarkTimer <0-172800> numberOfResponses <1-32> pingInterval <0-99999>
Command Parameters
Note
When the pingInterval and highWaterMarkTimer parameters are both set to 0, the ENUM server remains black listed until the parameters are reconfigured.
enumArsProfile Parameters
| Parameter | Length/Range | Default | Description |
|---|---|---|---|
| 1-23 | N/A | <enumArsProfile name> – Configure this parameter with the name of the Address Reachability Service (ARS) profile that will be associated with the lwresdProfile. |
| N/A | N/A | The blacklisting configuration.
|
whiteListing | N/A | N/A | Configure this parameter with the name of the Address Reachability Service (ARS) profile that will be associated with the
|
Command Examples
set global servers enumArsProfile Test blackListing numberOfFailures 5 duration 60
set global servers enumArsProfile Test whiteListing numberOfResponses 1 pingInterval 5 highWaterMarkTimer 86000
commit
show global servers enumArsProfile
enumArsProfile Test {
blackListing {
numberOfFailures 5;
duration 60;
}
whiteListing {
numberOfResponses 1;
pingInterval 5;
highWaterMarkTimer 86000;
}
}
ENUM Domain Name
Command Syntax
% set global servers enumDomainName <domain_name>
forwardersData <0-99999>
forwarderDescription <description>
forwarderIP <IPv4 or IPv6 address>
eDNSBufferSize <0 | 512-4096>
eDNSType <no | yes>
loadDistribution <proportion | roundRobin | sequence>
queryRetryTimer <0-10000 ms>
zoneType individual
Command Parameters
Note
All forwarderIP entries for this enumDomainName must be configured with the same loadDistribution type and queryRetryTimer value because attributes apply to ENUM domain, not individual forwarderIP entries.
Note
ENUM Domain Name Parameters
Parameter | Length/Range | Description |
|---|---|---|
<domain_name> | 1-63 characters | The name of the ENUM domain containing forwarderIP entries for load balancing. |
forwardersData | 0-99999 | <priority #> – Priority or sequence number of each
|
eDNSType | N/A | Set this flag to
|
eDNSBufferSize | 0 | 512-4,096 | If this parameter is configured as any value other than zero, the OPT record uses this value when the If this parameter is configured as |
loadDistribution | N/A | Load distribution strategy. Refer to ENUM Support for details.
|
queryRetryTimer | 0-10000 | The time, in milliseconds, that SLWRESD process waits before trying the next IP in the |
zoneType | N/A | The zone type for this ENUM domain.
|
ENUM Domain Name Label
Command Syntax
% set global servers enumDomainNameLabel DEFAULT_ZONE_LABEL enumDomainNameId <enumDomainName's name>
Command Parameters
ENUM Domain Name Label Parameters
Parameter | Description |
|---|---|
enumDomainNameLabel |
|
ENUM Message Definition
Command Syntax
%
Command Parameters
Global ENUM Service Parameters
Parameter | Length/Range | Description |
|---|---|---|
ENUM Service
To support ENUM services for the SBC in ERE mode, manually create an ACL rule for the ENUM server to allow packets (ENUM responses) from the ENUM server into the SBC. Set the Fill Rate for the rule to a higher value (for example, Fill Rate = 2000) to support high ENUM call loads (more than 20 cps).
As an example, set the fillRate to a higher value (e.g., fillRate = 2000) to support high ENUM call loads (more than 20 cps).
Example ACL Rule
% set addressContext default ipAccessControlList rule ENUMSEV precedence 1 protocol any sourceIpAddress <ENUM_SERVER_ADDRESS> sourceAddressPrefixLength 32 action accept fillRate 50 bucketSize 50 state enabled
Refer to IP Access Control List - Cloud - CLI for configuration details.
Command Syntax
% set global servers enumService <name>
criteria triggerCriteria <criteria>
defaultTreatment <applyFinalTreatment | routeAsDialed>
enumDefinitions privateDomainNameForEnumLookups <private_domain_name>
flags
active <disable | enable>
processCallingNumber <disable | enable>
processNewANI <disable | enable>
sendOrigDialedNumOverEgress <disable | enable>
skipFurtherNumberTranslationServices <disable | enable>
priority <0-255>
requestTimeOut <0-2147483647>
serviceType <cnam | lnp | sipAor>
Command Parameters
Global ENUM Service Parameters
Parameter | Length/Range | Description |
|---|---|---|
<service_name> | 1-23 | ENUM service name. |
criteria | 1-23 | triggerCriteria <criteria> – Trigger criteria to use for this ENUM service. The characters #%^&(){}<>,/\;`[]=!$"*?|~ and SPACE are not allowed. |
defaultTreatment | N/A | Default treatment to apply to this ENUM service.
|
enumDefinitions | N/A | Use this parameter to specify how to treat ENUM definitions.
|
flags | N/A |
|
priority | 0-255 | Specifies the priority (order) of execution of ENUM services. Specifying a priority value is mandatory. |
requestTimeOut | 0-2147483647 | Request timeout value, in milliseconds. (default = 2000) |
serviceType | N/A | Use this parameter to specify the ENUM service type for this ENUM service.
|
Overview
Content Tools