Instantiating an HA SBC SWe Instance from CFN

Prerequisites for AWS CFN Install of SBC HA Instance

Prior to initiating a CFN-based install of an HA SBC instance, perform the following:

1. Create a VPC for use in the deployment. Refer to Create a VPC for the SBC SWe.
2. Create Internet Gateway for use in the deployment. Refer to Create an Internet Gateway for SBC SWe
3. Create Key Pairs for Linux shell access and Administrator access. Refer to Create Key Pairs for the SBC SWe.
4. Create Subnets for use in the deployment. Refer to Create Subnets for the SBC SWe.
5. Create Security Groups for use in the deployment. Refer to Create Security Groups for SBC SWe.
6. Update or create Route tables for the newly created subnets. Refer to Create Route Tables for SBC SWe.
7. Create a placement group for the SBC deployment. Refer to Create Placement Groups.
8. Create a Policy and Role for the SBC instance. Refer to Create an Identity and Access Management (IAM) Role for SBC SWe.

Instantiate an HA SBC Instance

To instantiate a standalone instance:

1. Log onto the AWS.

2. Click the Services drop-down list.
   The Services list is displayed.

3. Click CloudFormation from Management Tools section.

   
   

   The stacks page displays.

4. Click Create Stack. The Select Template page displays.

5. In the Choose a template section, select Upload a template to Amazon S3.
6. Click Choose File to navigate through the folders and select the template.
   The selected template displays.
   
   

7. Click Next.
   The Create A New Stack page displays.

   
   
   
   
   
   
   
   
   
   
   
   
   

   Note

   If you wish to use pre-allocated EIPs for management, set EIPAssociationForMgt to No at that field prompt.

   After the deployment has completed, you will need to manually associate the pre-allocated EIP to Mgmt (Eth0) Primary and secondary IPs.

   
   
   

   Note

   Ribbon recommends using an RAMP Private IP in the CFN template for RAMP registration. If a public IP is used for RAMP registration using the SBC CFN template, then you must add the RAMP public IP to the SBC security group rules for communication.

8. In the Stack name field enter a unique name for this SBC stack. A stack is a collection of AWS resources you create and delete as a single unit.

9. Enter the required values for the Parameter fields. The following table describes the create stack parameters.

   Caution

   Third party CPU setting of more than two vCPU is not supported with p3.2xlarge instances due to the vCPU requirement of the Standard_GPU_Profile.

   
   

   Create Stack Parameters

   Parameter Section	Field	Description	Mandatory	Can Leave Blank	Customizable by User
   Elastic IP configuration	EipAssociationOnMgt	Select "Yes" from the drop-down menu to associate an EIP for the MGT0 interface to login and access the SBC application from public networks. Select "No" if the EIP is not required. Using this option, the SBC management port is not accessible from outside of the AWS cloud.  Note: Only choose "No" when the VPC interface endpoint is associated with the SBC MGT subnet. Refer to the topic VPC Endpoint-Based HA Installation.
   Elastic IP configuration	NumberOfEIPOnPkt0	The number of Elastic IPs to be associated with PKT 0 interface. Note: Default is 0
   Elastic IP configuration	NumberOfEIPOnPkt1	The number of Elastic IPs to be associated with PKT 1 interface. Note: Default is 0
   Network configuration	SecurityGrpHa0	Acts as a firewall for associated Amazon EC2 instances, controlling both inbound and outbound traffic for HA0.
   Network configuration	SecurityGrpMgt0	Acts as a firewall for associated Amazon EC2 instances, controlling both inbound and outbound traffic for MGT0.
   Network configuration	SecurityGrpPkt0	Acts as a firewall for associated Amazon EC2 instances, controlling both inbound and outbound traffic for PKT0.
   Network configuration	SecurityGrpPkt1	Acts as a firewall for associated Amazon EC2 instances, controlling both inbound and outbound traffic for PKT1.
   Network configuration	SubnetIdHA0	Subnet ID of an existing subnet in your Virtual Private Cloud (VPC) for HA0.
   Network configuration	SubnetIdMgt0	Subnet ID of an existing subnet in your Virtual Private Cloud (VPC) for Mgt0.
   Network configuration	SubnetIdPkt0	SubnetId of an existing subnet in your Virtual Private Cloud (VPC) for Pkt0.
   Network configuration	SubnetIdPkt1	SubnetId of an existing subnet in your Virtual Private Cloud (VPC) for Pkt1.
   Network configuration	VpcId	Select a VPC with Subnet, Security Group, etc., selected earlier.
   Placement of Instance	PlacementId	A placement group ID of logical group of instances within a single Availability Zone. This is an optional field and can be blank.
   Placement of Instance	Tenancy	The Tenancy Attribute for this instance.
   Reverse NAT configuration	ReveseNatEnablePkt0	Enable or disable reverse Network Address Translation (NAT) functionality for PKT0 interface. Set this field to true, to attach the assigned EIP on PKT0 and use it without SMM rule. Refer to EipAssociationXface for associating EIP for the required interfaces. Note: When set to False, the SBC application cannot use the attached EIP.
   Reverse NAT configuration	ReveseNatEnablePkt1	Enable or disable reverse Network Address Translation (NAT) functionality for PKT1 interface. Set this field to true, to attach the assigned EIP on PKT1 and use it without SMM rule. Refer to EipAssociationXface for associating EIP for the required interfaces. Note: When set to False, the SBC application cannot use the attached EIP.
   Secondary IP configuration for PKT0 and PKT1	NumberOfAlternateIPOnPkt0	Alternate IP address for packet port 0. Note: Default is 1. If you are using more than one IP for alternate IPs, use comma separated IPs list.
   Secondary IP configuration for PKT0 and PKT1	NumberOfAlternateIPOnPkt1	Alternate IP address for packet port 1. Note: Default is 1. If you are using more than one IP for alternate IPs, use comma separated IPs list.
   Security configuration	AdminSshKey	Existing EC2 KeyPair name to enable SSH access to admin CLI on SBC instance.
   Security configuration	LinuxAdminSshKey	Existing EC2 KeyPair name to enable SSH access to Linux shell on SBC instance.
   Storage configuration	IOPS	Enter IOPS reservation for io 1 type EBS volume
   Storage configuration	VolumeSize	Enter the size of disk required in GB. The minimum size is 65 GIB. However, you can choose more.
   Storage configuration	VolumeType	Select the type of volume for SBC. Ribbon recommends that SBC use io1 type.
   System configuration	ActiveInstanceName	This specifies the actual CE name of the SBC active instance. For more information, refer to System and Instance Naming in SBC SWe N:1 and Cloud-Based Systems. CEName Requirements: Must start with an alphabetic character. Only contain alphabetic characters and/or numbers. No special characters. Cannot exceed 64 characters in length
   System configuration	AMIID	Amazon Machine Image (AMI) is an encrypted machine image which is like a template of a computer's root drive. For example, ami-xxxxxxxx.
   System configuration	IAMRole	The name of the IAM role for SBC SWe instance. For more information on IAM Role, refer to Creating Identity and Access Management (IAM) Roles.
   System Configuration	EnableCloudWatchMetrics	Enable this for capturing instance metrics at cloudwatch. Note: Default is false.	Yes , when CloudWatch features are using Interval Stats
   System configuration	InstanceType	Type of instance created from stack. Note: Ribbon recommends m5.xlarge or higher instance type if this instance type is available in your zone. Use c5.2xlarge instance type or higher to handle more calls with transcoding.
   System configuration	SBCPersonality	The type of SBC for this deployment. In this release, always set the personality to isbc.
   System configuration	StandbyInstanceName	This specifies the actual CE name of the SBC standby instance. For more information, refer to System and Instance Naming in SBC SWe N:1 and Cloud-Based Systems. CEName Requirements: Must start with an alphabetic character. Only contain alphabetic characters and/or numbers. No special characters. Cannot exceed 64 characters in length
   System configuration	SystemName	Specifies the actual system name of the SBC instance. For more information, refer to System and Instance Naming in SBC SWe N:1 and Cloud-Based Systems. System Requirements: Must start with an alphabetic character. Only contain alphabetic characters and/or numbers. No special characters. Cannot exceed 26 characters in length.
   System Configuration	UseAnonymizationFeature	Enable this for Anonymization. Note: Default is false.	Yes, when CloudWatch features are using ACT, TRC
   Third Party Applications Provisioning	ThirdPartyCPUs	Enter the number of CPUs to be reserved for use with third-party apps. Note: Default is 0	Yes, when using CloudWatch features
   Third Party Applications Provisioning	ThirdPartyMem	Enter the number of MB of memory to be reserved for use with third-party apps.  Note: Default is 0	Yes, when using CloudWatch features
   EMS Registration Configuration	EMSUsername	The EMS Username used to log in the EMS (RAMP).
   EMS Registration Configuration	EMSPassword	The EMS Registration password.
   EMS Registration Configuration	EMSFqdn	The EMS fully qualified domain name.
   EMS Registration Configuration	EMSIP1	EMS IP Address 1.
   EMS Registration Configuration	EMSIP2	EMS IP Address 2.
   EMS Registration Configuration	ClusterID	Cluster/VNF ID Value from the EMS Cluster Management.
   EMS Registration Configuration	EMSDownloadConfig	Download Configuration from the EMS.

10. Click Next.
    The Options page displays.

11. Optionally you can choose to Tag your deployment with a Key-value pair, IAM Role Permissions, Rollback Triggers or other advanced Options.
    

12. Click Next.
    The Review page displays.
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
13. Review the stack details and click Create
    The CloudFormation Stacks page displays.
    
    On successful stack creation, the stack is listed.
    

Verify the Instance Creation

Perform the following steps to view the SBC SWe instances created:

1. Click the Services drop-down list.
   The Services list is displayed.

2. From the left pane click EC2.

   

   The EC2 Dashboard page is displayed.
    

3. From the left pane under Instances click Instances. The instances table lists the new instance.

   

   Caution

   If deleting an instance from CFN, be aware that AWS does not delete volume(s) automatically. They must also be deleted from the AWS UI if you do not want volumes of deleted instances (standalone, HA or HFE-based SBC installation).