In this section:
The SBC 5100, SBC 5110, SBC 5200, and SBC 5210 platforms are no longer supported beginning with the SBC Core 10.0.0R0 release. This release supports SBC 5400/7000/SWe platforms. Contact Ribbon Sales for upgrade information.
Zone CAC
Use the zone CAC parameters to configure call admission control (CAC) settings for a zone on ingress, on egress, and for the zone as a whole.
Command Syntax
Unless noted otherwise, the parameter values in this section apply to the SBC Core.
% set addressContext <addressContext_name> zone <zone_name> cac bandwidthLimit <0-2147483647, or unlimited> bandwidthLimitThreshold <0-100> bandwidthVideoThreshold <0-100> callLimit <0-2147483647, or unlimited> callLimitThreshold <0-100> egress emergencyOversubscription <0-1000> extendedEmergencyIpLimit <0-40000> hpcOversubscription <0-100> ingress registrationLimit <0-2147483647, or unlimited>
SIP subscription CAC limits are not applied to SUBSCRIBE requests from registered users in access deployments.
Command Parameters
Parameter | Length/Range | Description |
---|---|---|
bandwidthLimit | 0-2147483647, or unlimited | Total bandwidth limit in Kbps/sec. |
bandwidthLimitThreshold | 0-100 | Bandwidth utilization notification threshold, as a percentage. (default = 0) |
bandwidthVideoThreshold | 0-100 | Enter threshold value (as a percentage of video bandwidth) to limit video streams to a specific bandwidth to prevent video calls consuming call bandwidth otherwise needed for audio calls. (default = 0) |
callLimit | 0-2147483647, or unlimited | Total number of calls allowed on this zone. (default = 'unlimited') |
callLimitThreshold | 0-100 | Call limit utilization notification threshold, as a percentage. (default = 0) |
egress | N/A | Egress-specific call admission control configuration. See the Egress Parameters table below for details. |
emergencyOversubscription | 0-1000, or unlimited | This parameter gives priority treatment to emergency calls by specifying the resource over-subscription percentage allowed for emergency calls, and represents the allowed percentage of emergency calls beyond the configured call limit. When the call limit is reached, normal calls are rejected but emergency calls are accepted up to an expanded limit. (default = 10) |
extendedEmergencyIpLimit | 0-40000 | Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
| N/A | Ingress-specific call admission control configuration. See the Ingress Parameters table below for details. |
registrationLimit | 0-2147483647, or unlimited | The number of concurrent registrations allowed in this zone. (default = 'unlimited') |
Egress
Command Syntax
% set addressContext <addressContext_name> zone <zone_name> egress callBurstMax <1-900, or unlimited> (SBC 7000 range is 1-2700) callLimit <0-2147483647, or unlimited> callRateMax <1-450, or unlimited> (SBC 7000 range is 1-1350) emergencyOversubscription <0-1000> extendedEmergencyIpLimit <0-40000> hpcOversubscription <0-100> registerBurstMax <1-3000 or unlimited> (1-1500 or unlimited for SBC 5400; 1-3000 or unlimited for SBC 7000) registerRateMax <1-3000 or unlimited> (1-1500 or unlimited for SBC 5400; 1-3000 or unlimited for SBC 7000)
Command Parameters
Egress Parameters
Parameter | Length/Range | Description |
---|---|---|
callBurstMax | SBC 7000: 1-2700, or unlimited | Maximum allowed burst (above the allowed sustained rate) for egress call attempts, in calls/second. (default = 'unlimited') |
callLimit | 0-2147483647, or unlimited | Total number of outbound concurrent calls allowed. (default = 'unlimited' ) |
callRateMax | SBC 7000: 1-1350, or unlimited | Maximum sustained egress call rate allowed in calls/second. (default = 'unlimited' ) Note: You can set bothcallRateMax and callBurstMax as "unlimited"; however, if you assign a value to one parameter, the other must also be assigned a value. |
emergencyOversubscription | 0-1000 | Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10) |
extendedEmergencyIpLimit | 0-40000 | Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
registerBurstMax | SBC 5400: 1-1500 or unlimited SBC 7000: | Specifies the maximum allowed egress burst (above the allowed sustained rate) for initial SIP registrations. The default value is unlimited. |
| SBC 5400: 1-1500 or unlimited SBC 7000: | Specifies the maximum allowed sustained egress rate (registrations per second) for initial SIP registrations. The default value is unlimited. Note: You can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. |
Ingress
Command Syntax
% set addressContext <addressContext_name> zone <zone_name> cac ingress callBurstMax <1-900, or unlimited> (SBC 7000 range is 1-2700) callLimit <0-2147483647, or unlimited> callRateMax <1-450, or unlimited> (SBC 7000 range is 1-1350) emergencyOversubscription <0-1000> extendedEmergencyIpLimit <0-40000> hpcOversubscription <0-100> packetRateMax <1-65535, or unlimited> registerBurstMax <1-3000 or unlimited> (1-1500 or unlimited for SBC 5400; 1-3000 or unlimited for SBC 7000) registerRateMax <1-3000 or unlimited> (1-1500 or unlimited for SBC 5400; 1-3000 or unlimited for SBC 7000)
Command Parameters
Ingress Parameters
Parameter | Length/Range | Description |
---|---|---|
callBurstMax | SBC 7000: 1-2700, or unlimited | Maximum allowed burst (above the allowed sustained rate) for ingress calls, in calls/second. (default = 'unlimited') |
callRateMax | SBC 7000: 1-1350, or unlimited | Maximum sustained ingress call rate allowed in calls/second. (default is 'unlimited') Note: You can set bothcallRateMax and callBurstMax as "unlimited"; however, if you assign a value to one parameter, the other must also be assigned a value. |
emergencyOversubscription | 0-1000 | Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10) |
extendedEmergencyIpLimit | 0-40000 | Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
packetRateMax | 1-65535, or unlimited | Maximum sustained packet rate allowed in packets/second. (default = 'unlimited') |
registerBurstMax | SBC 5400: 1-1500 or unlimited SBC 7000: | Specifies the maximum allowed ingress burst (above the allowed sustained rate) for initial SIP registrations. The default value is unlimited. |
registerRateMax | SBC 5400: 1-1500 or unlimited SBC 7000: | Specifies the maximum allowed sustained ingress rate (registrations per second) for initial SIP registrations. The default value is unlimited. Note: You can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. |