In this section:

Use the Type Admin window to configure event log handling for each type of event log.

To View Type Admin Configuration

On the SBC main screen, go to Administration > Accounting and Logs > Event Log > Type Admin. The Type Admin window opens showing a row for each type of event log with its current configuration settings.

Type Admin Window

 

To Edit Type Admin Configuration 

To edit the configuration of one of the event log types, click the radio button next to the specific type. The Edit Selected Type Admin window opens for the selected type with its current configuration settings shown. In the following example the selected type is "System."

Edit Selected Type Admin (System)

The following parameters are displayed:

Type Admin Options

Parameter

Description

Type

The type of the event log. Each type has separate configuration parameters and logs to a separate file.

State

Specifies the requested state of the given event log type.

  • Disabled – Logging is not activated.
  • Enabled – (default) Logging is activated.
  • Rollfile

 Accounting logs cannot be disabled.

File Count

The number of event log files that will be maintained for this event type. All event types will overwrite the oldest file when the file count is exceeded. A warning will be issued when the count approaches the maximum. Enter a value between the range 1 and 2048.

File Size

The maximum size (in KB) that a single event log file will ever grow to. Enter a value between in the range (256-65535) KB. File size should be set to 65535 for trace and account logs when trying to trace all the calls on the system for use with Protect.

Message Queue Size

The number of event log message entries to buffer before writing them to disk. The size may be a value between 2 and 100. The default is 10. If capturing all of the SIP PDU messages in the trace log for use with Protect, set this value to 100 for the trace log.

Save To

Save events. The values are:

  • None - Events are not saved
  • Disk - Events are saved to disk

Filter Level

The filter severity level of events. Events that are at least as severe as the designated level will be logged. Noevents suppresses all events of this type from being logged.

Rollover Start Time

Specifies the start time for event log rollover. The format is CCYY-MM-DDTHH:MM:SS. For example: 2010-01-01T01:01:01.

Rollover Interval

Enter the number of seconds for the event log rollover interval. The range is 0 to 31536000.

Rollover Type

Event log rollover type. Options are:

  • Nonrepetitive (default) – The rollover will occur once at the specified single instance.
  • Repetitive – The rollover will occur repeatedly at the specified intervals.

Rollover Action

Event log rollover actions. The values are:

  • Start - Start event log rollover at the specified starting time.
  • Stop - Stop event log rollover.

File Write Mode

Identifies event log NFS write mode. The values are:

  • Default - Log data is written to NFS as a 1344 byte packet.
  • Optimize - Log data is written to NFS as an 8000 byte packet.
    Optimize write mode results in IP fragmentation, but yields better throughput.

Syslog State

Enable this option to log events of specified type to syslog.

  • Disabled (default)
  • Enabled

Note: Syslog Configuration is not supported for Packet and Memusage logs.

Rename Open Files

Enable this option to append an ".OPEN" extension to accounting and files which are open for writing.

  • Disabled (default)
  • Enabled

NOTE: You must enable the Signaling Packet Capture State parameter to capture SIP and H.323 packets (refer to Call Trace and Packet Capture - Signaling Packet Capture for configuration details).

Once Signaling Packet Capture State is enabled, any subsequent changes tothe SBC device configurations or filter information will not be available to signaling packet captures until the state is reset (state is disabled, and then re-enabled).

Disk Throttle LimitSpecifies the limit on INFO level messages logged to the disk in one second. A value of 0 disables the limit. The default is 10000 and the value can go up to 4,294,976,295. For the trace log, if tracing is being performed to capture all of the SIP PDU for all of the calls on the system for use in conjunction with Protect, then this value needs to be tuned to accommodate the maximum call load anticipated for the SBC instance. For example, for a call rate of 1350 cps and assuming 14 messages in a basic SIP call (ingress and egress legs), it would require a total of 18,900 messages. Adding this to the default 10000, the recommendation in this case would be to set the limit at 30,000. (Applies only to the System type.)
Event Log Validation

Specifies whether the logs at rest for this log type should be cryptographically hashed. The values are:

  • Disabled (default)
  • Enabled

Hashing is only recommended for the security and audit logs. These are the main logs required to triage security issues and do not roll very frequently. 

IMPORTANT: You must disable this control for any logs which are rolling at a very high rate, for example, if capturing trace logs of all SIP PDUs for use with Protect.

If logs are being exported using Rsyslog then there is no need to enable Event Log Validation as the logs are copied off the SBC before they could be modified. Refer to OAM - Event Log - Platform Rsyslog.

Compression Support

Specifies whether files are compressed. (Applies only to the Acct type.)

  • Both The SBC generates both compressed and uncompressed CDR files
  • None For backward compatibility, uncompressed CDR files
  • Only – The SBC generates compressed CDR files
Compression Days to KeepThe number of days to keep compressed files before deleting, from 1-7 (default = 5). (Applies only to the Acct type.)
Compression Cleanup DirectoryAlternate directory name (containing no slashes) under the log file directory from which compressed files are removed after Compression Days to Keep days elapse. (Applies only to the Acct type.)


Make any required changes and click Save to apply the changes to the selected event log type.