In this section:

This section describes the configuration parameter values to set from the Configure Devices page. The following settings are configurable.

Network Settings

Use the following parameters to configure the network settings:

  • LAN IP Address: Enter the IP address used by the EdgeMarc for the private internal network.
  • Netmask: Select the Subnet Mask.
  • WAN Interface IPv4 settings (Static IP/ DHCP): Select the type of IPv4 WAN interface.
  • WAN IP Address: The static IP address used by the EdgeMarc for the WAN, or DHCP.
  • WAN gateway: The default gateway address.
  • Manually Set DNS: DNS server information to override any negotiated connection settings for DNS servers.
  • Enable SNTP: Synchronize with an SNTP server on the network.
  • Enable DHCP Server: Enable DHCP Server on LAN interface.
  • Secondary WAN Interface IPv4 settings: Select the type of IPv4 Secondary WAN interface from any of the given options:
    • Disable Secondary WAN
    • Static IP
    • DHCP
  • Manually set DNS for Secondary WAN: DNS server information to override any negotiated connection settings for DNS servers for secondary WAN.

Security Settings

Use the following parameters to configure the security settings: 

  • Allow SSH access through firewall: Select this option to allow SSH access through the firewall. 
  • Allow HTTP access through firewall: Select this option to allow HTTP access through the firewall. 
  • Allow HTTPS access through firewall: Select this option to allow HTTPS access through the firewall. 
  • Allow SNMP access through firewall: Select this option to allow SNMP access through the firewall.

Admin/Service Config Settings

Use the following parameters to configure the Admin/Service Config Settings:

  • Enable SNMPv1: Select this option to enable SNMPv1. 
  • Enable Remote System Logging: Select this option to enable Remote System Logging.
  • Enable MOS Scoring: Select this option to enable MOS Scoring.
  • Enable Analytics: Select this option to enable Analytics.
  • Enable System Monitor: Select this option to enable System Monitor.

Trusted Hosts Settings

Trusted Hosts allows a user to define a list of hosts or networks that are allowed to access this system via management protocols. Use the following parameters to configure the Trusted Hosts Settings: 

  • Enable Trusted Hosts: Select this option to enable/disable Trusted Hosts. After choosing ‘enable trusted hosts’, an option to configure the list displays. 
  • Set IP Addresses for Trusted Hosts: List of hosts or networks that are allowed to access this system via management protocols. 
  • Netmask: Select the Subnet Mask.

VoIP Settings

Use the following parameters to configure the VoIP settings: 

  • SIP Server Name: If a SIP ALG is needed, enter the address (either an IP or URL). 
  • SIP Server Port: Enter the port number of the SIP server. 
  • SIP Server Transport: Select the SIP server transport settings to translate the outgoing B2BUA SIP signaling to the selected transport before forwarding it to the SIP server.

  • Use Custom Domain: Select this to enable/disable the SIP server custom domain. 

  • Enable Multi-Homed Outbound Proxy Mode: This option allows or prevents phones from using a Softswitch FQDN while using the EdgeMarc LAN IP as its outbound proxy. But the EdgeMarc always allows SIP messages if the phone uses an IP address instead of an FQDN. This option does not have control over the SIP messages.

  • Client UDP Listening ports: These are the port(s) on which the system will listen for SIP over UDP messages from SIP clients. 

  • Enable LAN device UA name pass-through: Select this to enable SIP UA name pass-through from LAN to WAN. 

  • Enable Transparent Proxy mode: This option allows the system to intercept SIP messages from a LAN-side phone regardless of the outbound proxy and SIP proxy values configured in the phone.

Survivability Settings

Use the following parameters to configure the Survivability Settings: 

  • Enable Keepalives: Select this to enable Keepalives. 
  • Error code to count as success: Select this to count error code as a success. 
  • Rate - Pacing behavior: Select the Rate - Pacing behavior. 
  • Rate - Pacing interval: Select the Rate - Pacing interval. 
  • Enable SIP server Redundancy: Select this to enable SIP server Redundancy. 
  • Enable Phone Expires Override: Select this to enable Phone Expires Override. 
  • Monitor SIP Messages: When this option is selected, the system monitors the SIP requests sent to the active server (excluding keepalive messages generated by the system).

Notification

Use the following parameter to configure the Notification Settings: 

Send notification once config is completed: Select this option to send notification once the configuration completes.