In this section:
To perform bulk actions in EdgeView, choose Devices > List.
To perform bulk Configure, perform the following steps:
Select Configure Device from Bulk Actions drop-down list.
The Configure Devices page appears.
Make the necessary configuration changes and then select CONFIGURE 2 DEVICES to save the changes (see Configure Devices page image).
You can also push a complete configuration from EdgeView 15 or higher to an EdgeMarc. Select Click to select a file or drag it here to push new configurations to an EdgeMarc (see Configure Devices page image).
Refer to the Configure Parameter Values section in this document to see in detail the Configuration Parameter Values.
To perform bulk SD-WAN Configuration, perform the following steps:
Select the required EdgeMarc devices to bulk configure from the devices list (see EdgeView Devices List image).
Select Configure SD-WAN from Bulk Actions drop-down list.
The Configure SD-WAN page appears.
Make the necessary configuration changes and then select CONFIGURE SD-WAN ON 2 DEVICES to save the changes (see Configure SD-WAN Screen image).
For more details on configuring SD-WAN, refer to Deploying SD-WAN on EdgeMarc Device.
To perform bulk upgrade, perform the following steps:
Select Upgrade Firmware from Bulk Actions drop-down list.
The Upgrade Firmware page appears where you can confirm the devices to upgrade.
Select UPGRADE TO to choose the version and then select UPGRADE 2 DEVICES (see upgrade Devices image).
To move devices in bulk from unassigned list to a collection, or from one collection to another, perform the following steps:
Select Move to Collection from the Bulk Actions drop-down list.
The Move to Collection page appears where you can select the collection to which you need to move the device, be it a specific collection or to the Unassigned collection.
Choose the collection and click MOVE 2 DEVICES (see Move Devices page image). You are prompted to confirm the action.
Before deleting EdgeMarc devices, please make sure that these devices have been taken out of service and shut down. If these devices are up and running during deletion, you may experience unexpected behaviors.
To delete EdgeMarc devices in bulk, perform the following steps:
Select Delete Device from the Bulk Actions drop-down list.
The Delete Devices page appears where you can confirm the deletion of devices.
Select DELETE 3 DEVICES (see Delete Devices page image). You are prompted to confirm the deletion.
Health report provides the list of devices connected to the EdgeMarc LAN port and their details (IP address, MAC Address, TWAMP)
To view bulk health report, perform the following steps:
Select Run Health Report from the Bulk Actions drop-down list.
The Run Health Report page appears where you can confirm the devices to run health report.
Select the RUN HEALTH REPORT FOR 2 DEVICES (see Devices Health Report page image).
The Action Log page appears.
To backup EdgeMarc devices in bulk, perform the following steps:
Select Backup Configuration from the Bulk Actions drop-down list.
The Backup Configuration page appears where you can confirm the devices to backup.
In order to restore your EdgeMarc device to a previous backup point, you should have your EdgeMarc device backed up earlier.
You can Restore your EdgeMarc device to only the available backup points.
To restore EdgeMarc devices in bulk, perform the following steps:
Select Restore Configuration from the Bulk Actions drop-down list.
The Restore Configuration page appears where you can select the date and time to which you are required to restore the devices.
Choose RESTORE 2 DEVICES (see Restore Devices page image). You are prompted to confirm the action.
To change the passwords of EdgeMarc devices in bulk, perform the following steps:
Select the required EdgeMarc devices for performing bulk actions from the devices list (see Configure Devices page image).
Select Change Passwords from the Bulk Actions drop-down list.
The Change Password page appears where you can set the Root Password, GUI User Root, and GUI User Rouser passwords.
Select Set all as and then enter Root Password, GUI User Root and GUI User (see Change Password image).
Select SET PASSWORD FOR 1 DEVICE (see Change Password image). The Change Password for 1 device page appears where you can confirm the password change.
Select CHANGE PASSWORD from the confirmation screen to change the passwords (see Change Password Confirm image).
To reboot EdgeMarc devices in bulk, perform the following steps:
Select the required EdgeMarc devices for performing bulk actions from the devices list (see Configure Devices page image).
Select Reboot Device from the Bulk Actions drop-down list.