EdgeMarc 7400 Back Panel

EdgeMarc 7400 Back Panel Components


Physical Label/TypeFunctionDescription
1

Port 1

LAN 1

10/100/1000 Mbps RJ-45 Ethernet port for LAN network connectivity.

Default IP: 192.168.1.1

2

Port 2

WAN 1

10/100/1000 Mbps RJ-45 Ethernet port for connectivity to the WAN or Internet network connectivity.

Default IP: None

3

Port 3

Mgmt

10/100/1000 Mbps RJ-45 Ethernet port for optional management network connectivity. This interface must not be on the same network as the WAN or LAN subnets. This network cannot be within a subnet contained in a “Route” statement.

4

Port 4

WAN 2

Secondary WAN Interface Port. 10/100/1000 Mbps RJ-45 Ethernet port for connectivity to the WAN or Internet network connectivity.

The port is covered with a removable RJ-45 cap. Remove the cap before use.

Supports basic routing in addition to the following:

• Dual WAN Port feature—Two discrete WAN interfaces with the ability to independently route

•  WAN failover / WAN Link Redundancy (WLR)

•  Link aggregation for WAN acceleration

Note: This port is unused if you are running a software release prior to 13.11.2.

5

Port 5

LAN 2

10/100/1000 Mbps RJ-45 Ethernet port for LAN network connectivity.

Default IP: 192.168.1.1.

The port is covered with a removable RJ-45 cap. Remove the cap before use.

Note: This port is unused if you are running a software release prior to 13.12.

6

Port 6

LAN 3

10/100/1000 Mbps RJ-45 Ethernet port for LAN network connectivity.

Default IP: 192.168.1.1.

The port is covered with a removable RJ-45 cap. Remove the cap before use.

Note: This port is unused if you are running a software release prior to 13.12.

7

Erase

Erase button

Press the Erase button in quick succession to control the following:

  • One click—No action.
  • Two clicks—Resets the CLI password to what is stored in the manufacturing configuration.

  • Three clicks—Restores to factory default settings and reboots the system.

    Note

    When restored to factory default settings, the current configuration is lost, disconnecting all VoIP devices, Internet connectivity, and network access for computers until the system is reconfigured.

    Note

     If the Erase button is disabled (as noted on the Admin page of the GUI) and you wish to reset the password, please contact the Global Support Assistance Center:

    Ribbon Support Portal:  https://ribboncommunications.com/services/ribbon-support-portal-login.

    Voice: +1-833-RIBBON1 (1-833-742-2661)

8

On/Off Switch

System power switch

Powers the system on and off.

9

VGA Port

Unused

Reserved for future use.

10

RJ-45 Port

Serial

Craft

Console

Port

RJ-45 serial craft console port for management.

Baud: 9600

Data: 8

Parity: N

Stop: 1

Flow Control: NONE

An RJ-45 to DB9 console cable is included in the box with the EdgeMarc 7400.

11

Power socket

LED

Power

Status

LED

Indicates the online/offline status for the power supply module. When the power supply module is online, the LED is green.

12

Power socket

LED

Power

Status LED

Indicates the online/offline status for the power supply module. When the power supply module is online, the LED is green.

13

Alarm

Release

Button

Red alarm button

This is an audible alarm that alerts you when one of the power supply modules has gone offline. Press the button to silence the alarm.

14

AC Power Socket (1)

Input power

Provides power to power supply module 1. Accepts a 3-pin shroud female plug.

15

Power supply module (1)

Power supply unit

Redundant power supply unit capable of powering the EdgeMarc 7400.

16

AC Power Socket (2)

Input power

Provides power to power supply module 1. Accepts a 3-pin shroud female plug.

17

Power supply module (2)

Power supply unit

Redundant power supply unit capable of powering the EdgeMarc 7400.

18

USB Ports

Unused

Reserved for future use.