DO NOT SHARE THESE DOCS WITH CUSTOMERS!

This is an LA release that will only be provided to a select number of PLM-sanctioned customers (PDFs only). Contact PLM for details.


In this section:

Use the GW Sig Port window to configure a signaling port for gateway-to-gateway (GW to GW) call signaling. The gateway-to-gateway signaling is a protocol that transports call signaling messages between SBC (and GSX) instances over a TCP connection and requires that an external PSX is part of the network. The SBC supports gateway-to-gateway signaling on all platforms, including virtualized SBC SWe deployments.

The parameters to define the GW signaling port differ based on your type of the SBC platform. For cloud-based deployments of SBC SWe (I-SBC or D-SBC), the parameters include IP Var so that the IP address for the port can be specified using a metavariable rather than a static IP address. For other SBC platforms, use the IP Address V4 or V6 parameter to enter a specific IP address.

The SBC supports a single GW signaling port at a time. The GW signaling port must be defined within the default address context and the defaultSigZone zone, and it must be assigned an index value of 1.


Note

Each signaling port within an Address Context must use a unique IP address and port number combination.


Note

The SBC 5210 and SBC 7000 systems support creating IP Interface Groups containing sets of IP interfaces that are not "processor friendly" (i.e. carried on physical Ethernet ports served by separate processors). However, restrictions exist regarding the usage of such Interface Groups.

(This ability does not apply to the SBC 5110 and 5400 systems which have only two physical media ports. IP interfaces from the two physical ports may be configured within the same IP Interface Groups without restrictions.)

For complete details, refer to Configuring IP Interface Groups and Interfaces.

View GW Sig Port

On the SBC main screen, go to Configuration > System Provisioning > Category: Base Provisioning > Signaling Ports > GW Sig Port.

The GW Sig Port window is displayed. The following figure shows the window for an I-SBC or D-SBC (cloud) deployment that includes the IP Var parameter.

Signaling Ports - Gw Sig Port with IP Address

 The following figure shows the window for non-cloud deployment that includes the IP Address V4 or V6 parameter.

Signaling Ports - Gw Sig Port with IP Address

Create the GW Sig Port

To create a new GW Sig Port,

  1. Select default from the Address Context drop-down and  defaultSigZone from the Zone drop-down.
  2. Click the New GW Sig Port on the GW Sig Port List panel.

The Create New Gw Sig Port window is displayed. The following example shows the parameters for an I-SBC or D-SBC deployment.

Gw Sig Port Create Window


The following fields are displayed:

Gw Sig Port Parameters

Parameter

Description

Index

Set the index for gateway signaling port to 1.

Ip Interface Group Name

Specify the name of the IP interface group used by this signaling port.

Ip Address

Specify the IP address for the gateway signaling listening port in IPV4 or IPV6 format.

This is a required parameter visible on hardware systems and SBC SWe systems that do not use metavariables.

Note: For cloud-based I-SBC, D-SBC SBC SWe deployments, this parameter is not visible.

Port Number

The logical port number of the TCP port to use for this connection. Must be 1-65535, default is 2569.

Role

The main role of the signaling port:
• primary(default)—the port that makes gateway signal link connection requests to other SBC, using its IP address as the local address for listening.
• secondary—an alternate port that is used for listening only and cannot be used to establish new gateway signal links.

When no primary port exists, connection requests to other SBC cannot be issued and calls which require them are disconnected.
When a secondary port is configured to be primary, the previous primary is automatically made secondary.

Mode

The operational state of the Gateway signaling service:
• inService(default)—the signaling port listens for incoming gateway signal link connection requests.
• outofService—the signal port is not available for incoming gateway signal link connection requests and thus cannot be used to create a new gateway signal links to other SBC.

State

The administrative state of this gateway signaling port:
• disabled—Not active
• enabled—Active

IP Var

Specify the metavariable to use to assign an IP address to the gateway signaling port in an I-SBC or D-SBC deployment. .

Note: This parameter is visible for only I-SBC and D-SBC deployments in the SBC SWe.

Edit the GW Sig Port

To edit any of the Gw Sig Ports in the list, click the radio button next to the specific Gw Sig Port name.

  1. Click the radio button next to the name of the entry you want to edit. The Edit Gw Sig Port window opens.

  2. Change the variable value and click Save.

Delete the GW Sig Port

To delete a GW Sig Port,

  1. Click the radio button next to the name of the entry you want to delete.
  2. Click the delete icon (X) at the end of the row.
  3. Confirm the deletion when prompted.