In this section:
| Common Call Statistics Terminology | |
|---|---|
| Stable Calls | Calls that are established and fully stable (connected and media cut-through type of calls) and will survive a fail-over. This excludes calls in establishing, clearing and updating states which will not survive a fail-over. |
| Active Calls | A snapshot of total number of active calls on the SBC at the point of execution of the status command. This count reflects the actual live calls on the box independent of the state of the call (setup, stable, updating or clearing). |
| Call Attempts | Accumulative number of attempted calls on this system since the last reboot/start-up, including calls where a setup was sent/received, uncompleted calls (calls failed, busy, not answered, etc.) and calls completed (answered). |
| Call Completions | Accumulative number of calls completed on this system since the last reboot/start-up. |
The SBC allows the operator to access data from the current interval and from the interval statistics table related to each object being monitored. The current interval consists of a statistics table entry that is accumulating data for the next interval report. The interval statistics table is a series of statistics table entries containing data from the most recently completed n intervals (where n is the number of intervals in the retention policy configuration).
Note
Refer to Links to Statistics Pages to navigate to a particular EMA or CLI statistics page.
Note
If using the EMS in your network, configure EMS PM data collection intervals for the SBC to be both:
- Equal to or greater than the SBC intervals size, and
- Not less than the SBC interval size multiplied by the SBC number of intervals.
Refer to Insight EMS User Guide for configuration details.
SBC intentionally does not display results of all calls when there is a high volume of traffic for the statistics below. This limitation is built into the SBC software to avoid excessive CPU usage and system timeouts.
- sipActiveGroupRegStatus
- sipActiveRegisterNameStatus
- sipDeletedRegisterNameStatus
- sipSigConnStatus
- sipSigTlsSessionStatus
Command Syntax
The command syntax of the objects related to the show status addressContext command is shown below.
> show status addressContext <addressContext name> cacOffenderStatus dnsGroup dynamicBlackList ipAccessControlList ipInterfaceGroup ipRouteStatus ipsec linkDetectionGroup linkDetectionGroupStatistics linkDetectionGroupStatus logicalSigAddressBindingStatus sipActiveGroupRegStatus sipActiveGroupRegSummaryStatus sipActiveRegisterNameStatus sipDeletedRegStatus sipDeletedRegisterNameStatus sipRegCountStatistics sipSubCountStatistics sipSubscriptionStatus surrRegCountStatistics zone zoneCurrentStatistics zoneIntervalStatistics zoneStatus
Command syntax for the above objects is defined in greater detail below.
cacOffenderStatus
> show status addressContext <addressContext_name> cacOffenderStatus <index number> egressCallRejects egressMessageRejects egressNotifyRejects egressOptionsRejects egressOtherRequestRejects egressReferRejects egressSubscribeRejects firstRejectAt ingressCallRejects ingressMessageRejects ingressNotifyRejects ingressOptionsRejects ingressOtherRequestRejects ingressReferRejects ingressSubscribeRejects ipAddress lastRejectAt messageFirstRejectAt messageLastRejectAt notifyFirstRejectAt notifyLastRejectAt optionsFirstRejectAt optionsLastRejectAt otherFirstRejectAt otherLastRejectAt referFirstRejectAt referLastRejectAt subscribeFirstRejectAt subscribeLastRejectAt zoneId
dnsGroup
> show status addressContext <addressContext_name> dnsGroup <dnsGroup name> dnsEntryDataStatus dnsEntryStatus dnsServerStatistics
dynamicBlacklist
> show status addressContext <addressContext_name> dynamicBlackList dblPolicerStatus cumulativeEnforcements policerEnforcements dblStatus currentAction <blacklist | watch> discardPacketCount effectivePeriodRemaining trunkGroup
intercept
> show status addressContext <addressContext_name> intercept callDataChannel interceptCallDataChannelStatistics
ipAccessControlList
> show status addressContext <addressContext_name> ipAccessControlList defaultAclStatistics getAggrPolicers ipAclOverallStatistics ipAclRuleStatistics ipAclRulesByPrecedence rule
ipInterfaceGroup
> show status addressContext <addressContext_name> ipInterfaceGroup <IG name> ipInterfaceStatus <IP Interface name> actualBandwidth allocatedBandwidth bwDeviation ifindex numMediaStreams oosReason operState rxPackets txPackets
ipRouteStatus
> show status addressContext <addressContext_name> ipRouteStatus <system name> <ip address> <prefix> protocol <bbnSpfIgp | bgp | ciscoEigrp | ciscoIgrp | egp | esIs | ggp | hello | icmp | idpr | isIs | local | netmgmt | ospf | other | rip>
ipsec
> show status addressContext <addressContext_name> ipsec ikeSaStatistics ikeSaStatus ipsecSaStatistics ipsecSaStatus systemStatistics
linkDetectionGroup
> show status addressContext <addressContext_name> linkDetectionGroup linkDetectionGroup linkDetectionGroupStatistics linkDetectionGroupStatus
linkDetectionGroupStatistics
> show status addressContext <addressContext_name> linkDetectionGroupStatistics <Link Detection Group name> doubleFailures failures singleFailures
linkDetectionGroupStatus
> show status addressContext <addressContext_name> linkDetectionGroupStatus <Link Detection Group name> failures
logicalSigAddressBindingStatus
> show status addressContext <addressContext_name> logicalSigAddressBindingStatus <ip interface>
sipActiveGroupRegStatus
> show status addressContext <addressContext_name> sipActiveGroupRegStatus <id> aorName | contactURI | creationTime | extExpirationTime | intExpirationTime | nextHopIpAddress | nextHopPortNum | regIdIsChild | registrarDomainName | registrarIpAddress | registrarPortNum | state
sipActiveGroupRegSummaryStatus
> show status addressContext <addressContext_name> sipActiveGroupRegSummaryStatus <registrar ip address> aorName nextRegIdIsChild state
sipActiveRegisterNameStatus
> show status addressContext <addressContext_name> sipActiveRegisterNameStatus <aor name> contactURI | creationTime | e2aeMediaSecurity | endPointBehindNapt | externalExpirationTime | internalExpirationTime | isRoaming | natPinholeLearningStatus | nextHopIpAddress | nextHopPortNum | registrarDomainName | registrarIpAddress | registrarPortNum | securityMechanismType | state
sipDeletedRegStatus
> show status addressContext <addressContext_name> sipDeletedRegStatus <id> aorName | contactURI | creationTime | nextHopIpAddress | nextHopPortNum | reasonCode | registrarDomainName | registrarIpAddress | registrarPortNum | terminationTime
sipDeletedRegisterNameStatus
> show status addressContext <addressContext_name> sipDeletedRegisterNameStatus <aor name> contactURI | creationTime | nextHopIpAddress | nextHopPortNum | reasonCode | registrarDomainName | registrarIpAddress | registrarPortNum | terminationTime
sipRegCountStatistics
> show status addressContext <addressContext_name> sipRegCountStatistics entry sipEmergencyRegAcceptTotal sipEmergencyRegActiveTotal sipRegCountAttempts sipRegCountCumCompletions sipRegCountPending sipRegCountStable sipRegCountTotal
sipSubCountStatistics
> show status addressContext <addressContext_name> sipSubCountStatistics entry sipSubCountAttempts sipSubCountCumCompletions sipSubCountPending sipSubCountStable sipSubCountTotal
sipSubscriptionStatus
> show status addressContext <addressContext_name> sipSubscriptionStatus <id> callId | expirationTime | nextHopIpAddress | nextHopPortNum | origEPDomain | previousHopIpAddress | previousHopPortNum | serverDomainName | state
surrRegCountStatistics
> show status addressContext <addressContext_name> surrRegCountStatistics entry surrRegActiveRegCount surrRegConfiguredCount
zone
> show status addressContext <addressContext_name> zone <zone name> callCurrentStatistics callFailureCurrentStatistics callFailureIntervalStatistics callIntervalStatistics filterSipSrc filterSipSrcStatistics gwSigPortStatistics gwSigPortStatus h323SigPortStatistics h323SigPortStatus peerPathchkStatus peerQosStatus peerSurrRegStatus sipArsStatus sipCurrentStatistics sipIntervalStatistics sipOcsCallCurrentStatistics sipOcsCallIntervalStatistics sipPeerCacStatus sipRegAdaptiveNaptLearningStatistics sipSigConnStatistics sipSigConnStatus sipSigPortStatistics sipSigPortStatus sipSigPortTlsStatistics sipSigTlsSessionStatus sonusSipSigPeerOvldStatusEntry trafficControlCurrentStatistics trafficControlIntervalStatistics trunkGroupQoeStatus trunkGroupStatus
zoneCurrentStatistics
> show status addressContext <addressContext_name> zoneCurrentStatistics <zone name> egressFailBWLimit | egressFailCallLimit | egressFailCallPolicing | egressSipRegFailLimit | egressSipRegPolicing | ingressFailBWLimit | ingressFailCallLimit | ingressFailCallPolicing | ingressSipRegFailLimit | ingressSipRegPolicing
zoneIntervalStatistics
> show status addressContext <addressContext_name> zoneIntervalStatistics <counter*> egressFailBWLimit | egressFailCallLimit | egressFailCallPolicing | egressSipRegFailLimit | egressSipRegPolicing | ingressFailBWLimit | ingressFailCallLimit | ingressFailCallPolicing | ingressSipRegFailLimit | ingressSipRegPolicing | intervalValid | time
* The counter (or number) is associated with a performance measurement in a previous 15-minute measurement interval. In the case where the agent has no valid data available for a particular interval, the corresponding object instance is not available; and upon a retrieval request a corresponding error message is returned to indicate that this instance does not exist (for example, a noSuchName error for SNMPv1 and a noSuchInstance for SNMPv2 GET operation).
In a system supporting a history of ‘n’ intervals with IntervalCount(1) and IntervalCount(n) the most and least recent intervals respectively, the following applies at the end of a 15-minute interval:
- discard the value of IntervalCount(n)
- the value of IntervalCount(i) becomes that of IntervalCount(i-1) for n >= i > 1
- the value of IntervalCount(1) becomes that of CurrentCount
- the TotalCount, if supported, is adjusted.
zoneStatus
> show status addressContext <addressContext_name> zoneStatus <zone name> activeSipRegCount | bwAvailable | bwCurrentLimit | bwInboundUsage | bwOutboundUsage | emergencyCallsBwUsage | inboundCallsUsage | outboundCallsUsage | priorityCallUsage | totalCallsAvailable | totalCallsConfigured
Command Parameters
The parameters associated with the 'show status addressContext' command are listed in the table below.
The following objects are included in this table for completeness, but only apply when using the
command:natDirectMediaGroup, rtpServerTable, surrRegCountStatistics
MultiExcerpt named showTableAddressContextParams was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
IPSEC Parameters
MultiExcerpt named showTableAddressContextIpsecParams was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
Zone Parameters
The following objects only apply when using the
command:dialogTransparency, disableZoneLevelLoopDetection, dnsGroup, domainName, flexiblePolicyAdapterProfile, gwSigPort, gwTrunkGroup, h323SigPort, h323TrunkGroup, id, ipPeer, messageManipulation, mtrmConnPort, remoteDeviceType, sipSigPort, sipTrunkGroup
MultiExcerpt named showTableAddressContextZoneParams was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
Command Examples
General Examples
To show zone current statistics:
admin@SBX15> show status addressContext default zoneCurrentStatistics
zoneCurrentStatistics defaultSigZone {
ingressFailCallLimit 0;
egressFailCallLimit 0;
ingressFailCallPolicing 0;
egressFailCallPolicing 0;
ingressFailBWLimit 0;
egressFailBWLimit 0;
ingressSipRegFailLimit 0;
egressSipRegFailLimit 0;
ingressSipRegPolicing 0;
egressSipRegPolicing 0;
}
To display the link Detection Group Status:
> show status addressContext default linkDetectionGroup
MGMT_LDG2 linkMonitorStatus MGMT_LM2
{
monitorStatus monitoring;
linkStatus up;
}
linkMonitorStatus MGMT_LM4
{
monitorStatus portDown;
linkStatus portDown;
}
linkMonitorStatistics MGMT_LM2
{
minTime 336;
maxTime 740;
averageTime 375;
singleFailures 0;
doubleFailures 0;
failures 0;
replies 13;
duplicateReplies 0;
lateReplies 0;
}
linkMonitorStatistics MGMT_LM4
{
minTime 0;
maxTime 0;
averageTime 0;
singleFailures 0;
doubleFailures 0;
failures 1;
replies 0;
duplicateReplies 0;
lateReplies 0;
}
To view default ACL statistics details:
> show status addressContext default ipAccessControlList defaultAclStatistics
defaultAclStatistics 9 {
protocol UDP;
application dns_udp_guest;
addressContextId *;
lifGrpId *;
sourceIpAddress "* (53)";
destinationIpAddress "* (0)";
policingMode PktRate;
bucketSize "50 pkt";
creditRate "1000 pkt/s";
polId 0;
polPriority 0;
packetAccept 0;
packetDiscard 0;
aggPol none;
owner vm;
vmGuestId Vm1;
}
Examples Showing Audio and Video Usage
Audio-Only CLI Output
admin@SBC01> show status addressContext default ipInterfaceGroup IG1
ipInterfaceStatus IF1 {
ifindex 13;
operState resAllocated;
oosReason notApplicable;
rxPackets 6488;
txPackets 140;
allocatedBandwidth 15800;
actualBandwidth 0;
bwDeviation 0;
numMediaStreams 1;
}
[ok][2014-07-17 16:47:26]
admin@SBC01> show status addressContext default ipInterfaceGroup IG2
ipInterfaceStatus IF2 {
ifindex 14;
operState resAllocated;
oosReason notApplicable;
rxPackets 270;
txPackets 2626;
allocatedBandwidth 15800;
actualBandwidth 0;
bwDeviation 0;
numMediaStreams 1;
}
[ok][2014-07-17 16:47:28]
admin@SBC01> show status addressContext default zone ZONE_IN_PCR1377 trunkGroupStatus
trunkGroupStatus TG_IN_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 1;
outboundCallsUsage 0;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 124;
bwOutboundUsage 0;
packetOutDetectState normal;
}
[ok][2014-07-17 16:47:36]
admin@SBC01> show status addressContext default zone ZONE_OUT_PCR1377 trunkGroupStatus
trunkGroupStatus TG_OUT_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 0;
outboundCallsUsage 1;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 0;
bwOutboundUsage 124;
packetOutDetectState normal;
}
Video-Only CLI Output
admin@SBC01> show status addressContext default ipInterfaceGroup IG2
ipInterfaceStatus IF2 {
ifindex 14;
operState resAllocated;
oosReason notApplicable;
rxPackets 236;
txPackets 1318;
allocatedBandwidth 128000;
actualBandwidth 21008;
bwDeviation 0;
numMediaStreams 1;
}
[ok][2014-07-17 16:33:21]
admin@SBC01> show status addressContext default ipInterfaceGroup IG1
ipInterfaceStatus IF1 {
ifindex 13;
operState resAllocated;
oosReason notApplicable;
rxPackets 5343;
txPackets 126;
allocatedBandwidth 128000;
actualBandwidth 23648;
bwDeviation 0;
numMediaStreams 1;
}
[ok][2014-07-17 16:33:25]
admin@SBC01> show status addressContext default zone ZONE_IN_PCR1377 trunkGroupStatus
trunkGroupStatus TG_IN_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 1;
outboundCallsUsage 0;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 1000;
bwOutboundUsage 0;
packetOutDetectState normal;
}
admin@SBC01> show status addressContext default zone ZONE_OUT_PCR1377 trunkGroupStatus
trunkGroupStatus TG_OUT_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 0;
outboundCallsUsage 1;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 0;
bwOutboundUsage 1000;
packetOutDetectState normal;
}
Both Audio and Video CLI Output
admin@SBC01> show status addressContext default ipInterfaceGroup IG1
ipInterfaceStatus IF1 {
ifindex 13;
operState resAllocated;
oosReason notApplicable;
rxPackets 6502;
txPackets 154;
allocatedBandwidth 143800;
actualBandwidth 0;
bwDeviation 0;
numMediaStreams 2;
}
[ok][2014-07-17 16:55:12]
admin@SBC01> show status addressContext default ipInterfaceGroup IG2
ipInterfaceStatus IF2 {
ifindex 14;
operState resAllocated;
oosReason notApplicable;
rxPackets 281;
txPackets 2635;
allocatedBandwidth 143800;
actualBandwidth 0;
bwDeviation 0;
numMediaStreams 2;
}
[ok][2014-07-17 16:55:19]
admin@SBC01> show status addressContext default zone ZONE_IN_PCR1377 trunkGroupStatus
trunkGroupStatus TG_IN_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 1;
outboundCallsUsage 0;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 1124;
bwOutboundUsage 0;
packetOutDetectState normal;
}
[ok][2014-07-17 16:55:31]
admin@SBC01> show status addressContext default zone ZONE_OUT_PCR1377 trunkGroupStatus
trunkGroupStatus TG_OUT_PCR1377 {
state inService;
totalCallsAvailable -1;
totalCallsInboundReserved 0;
inboundCallsUsage 0;
outboundCallsUsage 1;
totalCallsConfigured -1;
priorityCallUsage 0;
totalOutboundCallsReserved 0;
bwCurrentLimit -1;
bwAvailable -1;
bwInboundUsage 0;
bwOutboundUsage 1124;
packetOutDetectState normal;
}
> show addressContext default sipActiveRegisterNameStatus
sipActiveRegisterNameStatus Sonus@10.54.8.191 268 {
state completed;
contactURI sip:Sonus@10.70.52.91:5070;
nextHopIpAddress 10.70.52.91;
nextHopPortNum 5070;
registrarIpAddress 10.128.254.86;
registrarPortNum 5090;
externalExpirationTime 3598;
internalExpirationTime 3600;
creationTime 2014-06-27T09:35:54+00:00;
registrarDomainName "";
endPointBehindNapt 0;
natPinholeLearningStatus none;
securityMechanismType none;
isRoaming 1;
}
Overview
Content Tools