EdgeMarc 6000 Back Panel


When lit, the Power LED indicates power is applied to the system. The Status LED changes to indicate the current state of the system. See the following table.

EdgeMarc 6000 Back Panel LEDs

LEDIndicatorDescription
PowerOff

Power is not supplied to the device.
Troubleshoot by verifying that the power adapter is connected to the unit and that power is supplied to the AC wall outlet.


Solid GreenPower is supplied to the unit.
StatusOffPower is not supplied to the device, or the bootloader failed to load.

Solid AmberThe device is running a self-test and is initializing.

Flashing AmberThe device is upgrading its software.

Flashing GreenThe device is loading the EdgeMarc VoIP Operating System (VOS).

Solid GreenVOS is ready.

RedThe device is in the bootloader. The kernel will change the LED to solid amber once the kernel starts loading.
SFP Link (1-2)Solid GreenPeer link is powered.

Flashing LEDFiber traffic is active.
T1/E1 (1-2)OffT1/E1 port is not in use.

Solid GreenT1/E1 port is in use.
Line (1-2)OffPSTN line is not in use.

Solid GreenPSTN line is in use.
Phone (1-8)OffPhone is in the on-hook state.

Solid GreenPhone is in the off-hook state.

EdgeMarc 6000 Back Panel Components

Physical Label/TypeFunctionDescription
Erase Erase button

Press the Erase button in quick succession to control the following:

  • One click—No action.
  • Two clicks—Resets the CLI password to what is stored in the manufacturing configuration.
  • Three clicks—Restores to factory default settings and reboots the system.

    Note

    When restored to factory default settings, the current configuration is lost, disconnecting all VoIP devices, Internet connectivity, and network access for computers until the system is reconfigured.

    Note

     If the Erase button is disabled (as noted on the Admin page of the GUI) and you wish to reset the password, please contact the Global Support Assistance Center:

    Ribbon Support Portal:  https://ribboncommunications.com/services/ribbon-support-portal-login.

    Voice: +1-833-RIBBON1 (1-833-742-2661)

Power InletAccepts power inputThis is a 12V 6A DC power socket.
Power/Status LEDsSystem power and statusRefer to EdgeMarc 6000 Back Panel LEDs for system and power status details.
Ethernet WAN ports 1-2WAN

2x1 10/100/1000 Mbps RJ45 Ethernet ports for WAN network connectivity (Copper).

SFP Link LEDsStatus

When lit, the SFP port is active and the copper RJ45 port is inactive. Refer to EdgeMarc 6000 Back Panel LEDs.

Optical WAN SFP ports 1-2WAN

Small Form-Factor Pluggable (SFP) for fiber (RJ45) Gigabit Ethernet connectivity. Either the SFP port (operating at 100/1000 Mbps) or the RJ45 (operating at 10/100/1000 Mbps) port can be active at a time.

Ethernet LAN ports 1-4LAN

2x2 10/100/1000 Mbps RJ45 Ethernet ports for LAN network connectivity.

LTE Micro SIM Slot4G LTE Support

Allows you to insert a 4G LTE micro SIM card thus allowing 4G network access.

Micro SD Card InterfaceStorage

Allows the EdgeMarc to save configurations and other files to an SD High Capacity (SDHC) Version 2.0 card. Maximum storage capacity is 32 GB per SD card, 4 GB per file. The SD card capabilities are configured with the web-based configuration menu and with command-line interface (CLI). Refer to EdgeMarc 6000 MicroSD Card Specifications.

USB 3.0 portData transmissionCan be used to connect USB devices.
T1/E1 LEDsStatus

When lit, the T1/E1 port is active. Refer to EdgeMarc 6000 Back Panel LEDs.

T1/E1 PRI ports 1-2T1/E1

Allows the user to transmit voice and data through PRI. 2 x T1/E1 default system configuration. Two ports are available on the main board.

Line ports 1-2FXO2 x RJ11 ports for 2 FXO channels.
Phone ports 1-8FXS8 x RJ11 ports for 8 FXS channels.
FXO/FXS LEDsStatus

Refer to Table 2-2 for FXO/FXS LED status details.

Management Console portsManagement

RJ45 serial craft port for console management. This port is used for debug or diagnostic purposes only.

Primary system configuration is performed from a web browser as described in the EdgeMarc User Guide.

  • No labels