You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 21 Next »

In this section:

SWe Lite supports the following (depending on your license):

  • For Memory (RAM), valid settings are 1 GiB, 2 GiB, or 4 GiB.
  • For vCPUs, valid settings are 1, 2 or 4 vCPUs.

For detailed information, refer to SBC SWe Lite Hardware and Software Requirements.

For adding vCPUs or increasing memory on a SWe Lite upgraded to Release 7.0, refer to Adding vCPU and Increasing Memory.

Prerequisites

Refer to Downloading the SBC SWe Lite Package prior to performing this procedure.

Note

The 

Unable to show "metadata-from": No such page "_space_variables"
supports one Network Management interface and up to four Network Media interfaces. The minimal networking configuration (one management and one media interface) requires two bridge interfaces configured on Hyper Visor host. To support maximum 1+4 configuration, Hyper Visor host must have five bridge interfaces configured prior to the Virtual Machine (VM) installation.

Limitations

  • Disk and network drivers must be selected during deployment only.

  • Changing disk or network drivers post-deployment is not recommended.

Create New Virtual Machine

  1. Start the Virtual Machine Manager. 

    Start Virtual Machine Manager

  2. Select New Virtual Machine from the File drop-down menu.

    New Virtual Machine

  3. From the Create New Virtual Machine dialog, select Import existing disk image and click Forward.

    Create New Virtual Machine

  4. Select Linux from the OS type drop-down menu.

  5. Select Debian Squeeze from the Version drop-down menu  .

  6. Click Browse and navigate to the location of the disk image. 

  7. From the Choose Storage Volume dialog, select file SBCSWeLite-disk1.qcow2, then click Choose Volume.

  8. Click Forward.

    OS Type and Version

  9. Set Memory (RAM) field to 1024, 2048, or 4096.

  10. Set CPUs to 1, 2, or 4, and click Forward.

     

    Memory and CPU Settings

  11. Enter the name of your new VM in the Name field.
  12. Select the Customize configuration before install option.

  13. From the New VM dialog, select the applicable network from the Network selection drop-down menu, and click Finish.

    Note

    This network is used for Management Interface.

    Finalizing Create New Virtual Machine

Customize Configuration

Add the Virtual Disks

  1. In the new pop-up window, select Disk 1 (VirtIO or IDE).

  2. Expand Advanced options and select IDE or VirtIO from the Disk bus drop-down menu.  

    Adding Hardware


  3. Click Add Hardware.
  4. Select Storage.

  5. Select Select or create custom storage.  

  6. Navigate to file SBCSWeLite disk2.qcow2.

  7. Select IDE or VirtiO from the Bus Type drop-down menu, and click Finish.

    Managing Storage

  8. Repeat steps 4-6 for IDE or Virtio Disk 3. 

    Repeat for Disk Three


Modify Network Interface Device Model

For 7.0 Release and later: Use virtio as the Network Interface Device Model.

  1. Select NIC.

  2. Select virtio from the Device model drop-down menu, then click Apply. 

    Modify Virtual Network Interface

Add Virtual Network Interfaces

  1. Click Add Hardware.
  2. From the Add New Virtual Hardware dialog, select Network.
  3. Select the desired Bridge id from the Network source drop-down menu.
  4. Select virtio from the Device model drop-down menu, and then click Finish.

  5. Repeat steps 1-4 for additional Network Interfaces.

    Adding Network Interfaces

 

Note

The 

Unable to show "metadata-from": No such page "_space_variables"
Virtual Machine requires five Virtual Network Interfaces configured, regardless of the actual number of Networks used by the guest VM.

Note

 The first Virtual NIC must use a dedicated bridge (Network source). The Network source can then be used to configure the four remaining Virtual NICs.

Sonus recommends that all customers review and, if necessary, optimize their Network Interface configurations before proceeding. Failure to do so could lead to interface mapping issues. See Mapping Network Interfaces and then return to this section.

Finalize Installation

  1. From the Virtual Machine dialog, click Begin installation.

    Begin Final Installation

     

    Note

     The configured VM starts automatically as shown below.

    SBC SWe Lite Running

  2. Click the monitor icon in the header to open the VM console. 

    Open VM Console

 

 

Complete Initial Setup

Proceed to SBC SWe Lite Initial Setup. After setup is complete, proceed to License Installation.

License Installation

Trial License Installation

If you are installing an SBC SWe Lite for a trial or demonstration deployment, proceed to Obtaining and Installing a SWe Lite Trial License.

Production License Installation

If you are installing an SBC SWe Lite instance to carry live enterprise traffic, proceed to Obtaining and Installing a SWe Lite License.

 

  • No labels