Parameter | Length/Range | Description |
---|
sweTrafficProfiles | 1-40 characters | <profile name> – Enter a unique SWe Traffic Profile name.
NOTE: The SBC SWe supports up to 20 SWe Traffic Profiles. To create additional profiles, delete any inactive custom profiles. |
bhcaPerSubscriber | 0-5 | <attempts> (default = 1) – Indicates busy hour call attempts (BHCA) per subscriber.
NOTE: This parameter is available when accessScenario = "true". |
callHoldTime
| 10-10800 | <seconds> – Enter the average call hold time, in seconds, of the call load for this profile. (default = 90) |
cryptoPercent | 0-100 | <% value> (default = 0) – The percentage of media sessions (including both transcoding and passthrough) requiring cryptographic treatment.The value is 50 when there is SRTP<->RTP interworking on all calls.
|
directMediaPercent | 0-100 | <% value> (default 0) – The call load percentage for direct media. The SBC does not convert Direct Media to pass-through calls.
NOTE: Ensure that the combined total percentage of directMediaPercent and transcodePercent does not exceed 100%. |
externalRefreshTimer | 15–86400 | <seconds> (default = 1800) – Use this parameter to specify the external registration timer, in seconds.
NOTE: The parameter is available only when isAccess is set to "true ". |
internalRefreshTimer | 15-86400 | <seconds> (default = 1800) – Use this parameter to specify the internal registration timer, in seconds.
NOTE: The parameter is available only when isAccess is set to "true ". |
isAccess | N/A | Set this flag to "true" to specify whether the deployment uses an access scenario. NOTE: When set to 'true ', internalRefreshTimer, registrationRefreshInterval and bhcaPerSubscriber parameters are available for configuration. |
| 0.0001 to 100 | Use this parameter to specify a media cost factor to use during capacity estimation. This factor affects the media plane estimation,such as crypto session and pass-through session estimation (default = 1). This parameter is applicable only to custom profiles. |
passthroughCodecProfile | N/A | The name of the codec mix to associate with the Passthrough Codec Profile. |
processorCapabilityIndexOverride | N/A | Use this flag to enable/disable index overriding of the default CPU performance computation by the SBC SWe. When set to 'true', the computed indices (which are calculated during system boot-up) are ignored, and the value provided in processorCapabilityIndexOverrideValue attribute is used for all estimations. NOTE: Since use cases for overriding the default computed indices are rare, it is recommended to not set the value of processorCapabilityIndexOverride to "true" to avoid inaccurate session numbers and vCPU computations. |
processorCapabilityIndexOverrideValue | 0.2-10 | Use this parameter to specify the computational value to use to override the default computed indices. (default = 1) NOTE: This parameter is available when processorCapabilityIndexOverride is set to "true". The value given should be in 0.2 to 10. |
| 0.0001 to 100 | Use this parameter to specify a signaling cost factor to use during capacity estimation. This factor affects the signaling plane estimation, such as cps estimation (default = 1). This parameter is applicable only to custom profiles. |
| 1.0 to 100 | Use this parameter to specify a received (rx) PPS factor to use during capacity estimation (default = 1). This parameter is applicable only to custom profiles. |
tonesPercent | 0-100 | <% value> (default = 0) – Use this parameter to specify the percentage of legs to use for tones treatment. |
transcodePercent | 0-100 | <% value> (default = 0) – Use this parameter to specify the percentage of call load to use for transcoded calls.
NOTE: The combined total percentage of directMediaPercent and transcodePercent should not exceed 100%. |
transcodingCodecProfile | N/A | The name of the codec mix to associate with the Transcoding Codec Profile. |
| 1.0 to 100 | Use this parameter to specify a transmitted (tx) PPS factor to use during capacity estimation. Use the Rx/Tx parameters for scenarios such as SIPREC where the received/transmitted PPS may not be the same (asymmetric) (default = 1). This parameter is applicable only to custom profiles. |
useGPUForTranscoding
| N/A | Use to specify the type of transcoding, GPU (true) or CPU (false). |