Use the procedures in this section to upgrade the DSC 8000 software. Software is upgraded in the following order:
Do not log onto the system using the shared IP addresses on the Management CPUs during the upgrade processes. These addresses are disabled as part of this process.
The examples used on this page are often the same between releases with the exception of the software version numbers.
Prerequisites
It is recommended that you perform the upgrade from a console port. A loss of connection while CPUs are being upgraded may require a rollback from the upgraded management CPU. Refer to Continue DSC 8000 Upgrade After Loss of Connection.
Workflow
Start
Log onto the DSC 8000 Management CPU in slot 13 (p19p2.5, Control shelf) or slot 2 (p19p1.3).
You must log onto the same CPU as the one you connected to upload the _upgrade.sh file.
Run command "upgrade" and press Enter.
The Operating System on the IO boards in the DSC 8000 may need to be upgraded before CPUs can be upgraded to Release 24.0.0. If the OS upgrade is required on the IO boards, the user will need to confirm the update of each IO board. The OS will be upgraded on the IO board and the card will be rebooted. This will cause all links associated to the affected IO board to go down until the card has rebooted and its software is running.
:::::::::::::::::::::::::::::::: Ribbon DSC :::::::::::::::::::::::::::::::: ┌───────────────────┐ │DSC8000 CPU Upgrade│ └───────────────────┘ _____________________________________________ Type "q" to quit from most prompts or CTRL-C. This process will prepare each CPU for upgrade before rebooting each CPU in order, isolating the reboots to avoid outages. Getting software versions...Done --------------------------------Check IO OS--------------------------------- Checking IOs for old OS that may need to be updated to communicate with the CPUs in the new load IO Information If an IO just got updated it may show up as 'Unable to get info' temporarily This is normal and will show proper info once the software is running ============== Slot: 8 OS: rel_12_00_p04.x511.img Needs OS Upgrade: Yes Slot: 11 OS: rel_12_00_p04.x511.img Needs OS Upgrade: Yes Slot: 21 OS: rel_12_00_p04.x511.img Needs OS Upgrade: Yes Detected IO(s) that need a new OS. Select IO to update the OS (0 to exit) [8, 11, 21]:
When the Check IO OS process is shown, enter the IO cards that need to be updated and then press Enter.
--------------------------------Check IO OS--------------------------------- Checking IOs for old OS that may need to be updated to communicate with the CPUs in the new load IO Information If an IO just got updated it may show up as 'Unable to get info' temporarily This is normal and will show proper info once the software is running ============== Slot: 8 OS: rel_12_00_p04.x511.img Needs OS Upgrade: Yes Slot: 11 OS: rel_12_00_p04.x511.img Needs OS Upgrade: Yes Slot: 21 OS: rel_12_00_p04.x511.img Needs OS Upgrade: Yes Detected IO(s) that need a new OS. Select IO to update the OS (0 to exit) [8, 11, 21]: 8 Software Update for IO Card in Slot #8 Pushing image to the IO card in slot #8 Executing verify_io_image.sh script on IO board in slot #8 DO NOT INTERRUPT!! THIS MAY TAKE A FEW MINUTES... Done: flashed Nexus image to IO board kernel0 and kernel1 Rebooting IO card in slot #8.
Repeat step 3 for the remaining IO Cards. After all IO Cards are updated.
IO Information If an IO just got updated it may show up as 'Unable to get info' temporarily This is normal and will show proper info once the software is running ============== Slot: 8 OS: rel_12_23_p01.x511.img Needs OS Upgrade: No Slot: 11 OS: rel_12_23_p01.x511.img Needs OS Upgrade: No Slot: 21 OS: rel_12_23_p01.x511.img Needs OS Upgrade: No All IOs are at the proper OS. An upgrade to the new build will need to be done after the CPU upgrade as usual
Type "yes", and press Enter to run the pre-upgrade check.
-----------------------------Pre Upgrade Check------------------------------ Please run a pre-upgrade check. Type "yes" to execute this check (exiting otherwise): yes Calling pre-upgrade check... ======== Performing upgrade PRE-checks... =========--------------------------------------------------- USB device check... --------------------------------------------------- Check USB device status on all the CPU or VM slots reported by cardlist/slotmon SLOT: 2 SLOT: 13 SLOT: 3 SLOT: 5 SLOT: 6 SLOT: 9 SLOT: 10 SLOT: 12 SLOT: 17 SLOT: 18 SLOT: 19 SLOT: 23 PASSED <Enter> to continue
Press Enter.
--------------------------------------------------- Ping connectivity check... --------------------------------------------------- Ping all slots which are CPUS or IOs in /opt/cpu_ss7gw/current/data/slot.conf to check card availability Ping all the slots reported by cardlist/slotmon to check packet loss -Slot: 2 Packets dropped: 0% -Slot: 13 Packets dropped: 0% -Slot: 3 Packets dropped: 0% -Slot: 12 Packets dropped: 0% -Slot: 17 Packets dropped: 0% -Slot: 26 Packets dropped: 0% -Slot: 31 Packets dropped: 0% -Slot: 40 Packets dropped: 0% -Slot: 45 Packets dropped: 0% -Slot: 54 Packets dropped: 0% -Slot: 18 Packets dropped: 0% -Slot: 19 Packets dropped: 0% -Slot: 21 Packets dropped: 0% -Slot: 22 Packets dropped: 0% -Slot: 23 Packets dropped: 0% -Slot: 24 Packets dropped: 0% -Slot: 25 Packets dropped: 0% PASSED <Enter> to continue
Press Enter:
One of the following messages will be displayed on the system depending on if SDA is deployed.
For a system doesn't deploy SDA:
--------------------------------------------------- Checking SDA configuration --------------------------------------------------- flex_slot.conf file doesn't exist ... This is expected if SDA is not configured on the system.
For a system that deploys SDA:
--------------------------------------------------- Checking SDA configuration --------------------------------------------------- Found DRBD 9.0 configuration on your system. PASSED
Press Enter.
Press Enter.
--------------------------------------------------- Free space check... --------------------------------------------------- -Available RAM space: 10604 MB -Available HDD (/var/log) space: 196165 MB -Available Compact Flash (/opt directory) space: 24689 MB PASSED <Enter> to continue
Press Enter.
Press Enter.
Press Enter.
---------------------------------------------------------------- Pre-setting and verifying new FS volume labels... ---------------------------------------------------------------- -CPU Slot: 2 FS volume labels set and verified -CPU Slot: 13 FS volume labels set and verified -CPU Slot: 3 FS volume labels set and verified -CPU Slot: 12 FS volume labels set and verified -CPU Slot: 17 FS volume labels set and verified -CPU Slot: 26 FS volume labels set and verified -CPU Slot: 31 FS volume labels set and verified -CPU Slot: 40 FS volume labels set and verified -CPU Slot: 45 FS volume labels set and verified -CPU Slot: 54 FS volume labels set and verified PASSED <Enter> to continue
Press Enter.
---------------------------------------------------------------- Checking if CPU Unused SATA Channels are Disabled... ---------------------------------------------------------------- -CPU Slot: 2 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 13 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 3 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 12 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 17 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 26 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 31 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 40 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 45 Unused SATA Channels are Disabled. Board Type: AMC124 -CPU Slot: 54 Unused SATA Channels are Disabled. Board Type: AMC124 PASSED <Enter> to continue
Press Enter.
--------------------------------------------------- Check Kernel and Mount Points. --------------------------------------------------- No tests to perform. <Enter> to continue
Press Enter.
Press Enter.
--------------------------------------------------- GWS Incoming Linkset check --------------------------------------------------- No GWS Incoming Linkset check needed for this X511 version <Enter> to continue
Press Enter.
------------------------------------------------------------------------- Checking uniqueness of Linkset Point Codes per NA ------------------------------------------------------------------------- PASSED <Enter> to continue
Press Enter.
------------------------------------------------------------------------- Checking if DB Definition of GTT NA and its LPC registration match ------------------------------------------------------------------------- PASSED <Enter> to continue
Press Enter.
--------------------------------------------------- Ensure pcs files are in proper locations... --------------------------------------------------- PASSED <Enter> to continue
Press Enter.
--------------------------------------------------- Ensure correct cluster password... --------------------------------------------------- PASSED <Enter> to continue
Press Enter.
--------------------------------------------------- Audit files check... --------------------------------------------------- Audit status: local copy of /opt/cpu_ss7gw/current/data/mtp.1.12.conf is different from 13, due to blank lines only Audit status: local copy of /opt/cpu_ss7gw/current/data/mtp.1.6.conf is different from 13, due to blank lines only Audit status: local copy of /opt/cpu_ss7gw/current/data/mtp.1.5.conf is different from 13, due to blank lines only Audit status: local copy of /opt/cpu_ss7gw/current/data/mtp.1.4.conf is different from 13, due to blank lines only Audit status: local copy of /opt/cpu_ss7gw/current/data/mtp.1.2.conf is different from 13, due to blank lines only Audit status: local copy of /opt/cpu_ss7gw/current/data/mtp.1.15.conf is different from 13, due to blank lines only Audit status: local copy of /opt/cpu_ss7gw/current/data/mtp.1.1.conf is different from 13, due to blank lines only Audit status: local copy of /opt/cpu_ss7gw/current/data/mtp.1.7.conf is different from 13, due to blank lines only 0 files were out of sync. Files: 93 Copied: 0 Deleted: 0 PASSED <Enter> to continue
Press Enter.
--------------------------------------------------- Test TIPC bearers... --------------------------------------------------- <Enter> to continue
Press Enter.
---------------------------------------------------------------- Checking if license keys need to be changed ---------------------------------------------------------------- PASSED Enter> to continue
Press Enter.
--------------------------------------------------- Reminder to take a backup... --------------------------------------------------- -It is highly recommended to take a backup of the system prior to starting the upgrade. Label and keep the backup in a safe place. <Enter> to continue
Press Enter.
====== The results of the PRE upgrade check are stored in /var/log/cpu_ss7gw/upgrade_data/PRE_UPGRADE_DATA.dsc_8000_21_0_3_nb20230118.Thu_May_1 8_02_39_36_EDT_2023 ====== Upgrade PRE checks completed. All checks PASSED. You may now proceed with the upgrade. ----------------------------Upgrade Information----------------------------- Using /shared/log/dsc_8000_23_0_0_nb20230517_upgrade.sh Upgrading to: 23_0_0_nb20230517 Requiring update: 2 3 12 13 17 26 31 40 45 54 Up to date: None I/O Cards: 18 19 21 22 23 24 25 Uncommissioned/Bad: None Confirmation to proceed with upgrade operations? (yes/no): yes Invalid input. yes or no is required
Type "yes" and press Enter.
Type "yes" and press Enter.
Upgrade execution order [13, 3, 12, 17, 26, 31, 40, 45, 54, 2]. To continue, press the Enter key:
Press Enter.
-----------------------------Final upgrade step----------------------------- Upgrading peer 13 Backup stats files..............Pass Storing user directories........Pass Modify boot file................Pass Setting restore information.....Pass Rebooting.......................Pass Waiting to recover..............Pass Waiting for system processes....Pass Machine 13 is complete, type "yes" to continue.: yes
The script will upgrade remaining cards one at a time. Respond with "yes" when prompted to continue.
If an asterisk appears beside any of the system cards during the verification process, the upgrade for the respective card was unsuccessful. In this case, it is recommended that you contact Customer Support.
Start
Make sure that the software and OS have been upgraded, all cards are running the same software, and that there are no asterisks beside any of the cards.
The output of the “CPU Versions” command shows that the CPU card has “UPGRADED” status if this is the first time the command is issued after an upgrade. All subsequent “CPU Versions” commands show the number of processes running on each CPU.
AVAILABLE SOFTWARE VERSIONS -------------------------------------------------------------------------------- No new load detected on system. Upload and run load .sh file on /var/log before attempting upgrade. CPU (current) dsc_8000_23_0_0_nb20230517 OS: Ribbon7.9.20 (Servicepack) [none applied] CPU (previous) dsc_8000_21_0_3_nb20230118 OS: Ribbon7.9.11 (Servicepack) RUNNING SOFTWARE VERSIONS (*=update required, ?=update unknown) CARD BUILD SERVICE O/S -SLOT----TYPE----------RELEASE--VERSION----PACK---IMAGE-------CARD STATUS--- -------------------------------------------------------------------------------- -- Chassis 1 -- Slot 2 MGMT 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 19 procs running Slot 13 MGMT 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 19 procs running Slot 3 ROUTING 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 25 procs running Slot 12 ROUTING 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 25 procs running -- Chassis 2 -- Slot 17 ROUTING 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 25 procs running Slot 26 ROUTING 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 25 procs running -- Chassis 3 -- Slot 31 ROUTING 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 25 procs running Slot 40 ROUTING 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 25 procs running -- Chassis 4 -- Slot 45 ROUTING 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 25 procs running Slot 54 ROUTING 23.0.0 (nb20230517) SP: OS: Ribbon7.9.20 25 procs running (p=servicepack is partially applied) Select CPU Slot number (17 26 31 40 45 54) to decommission an optional CPU.
Start
Select Switch Versions, and press Enter.
AVAILABLE SOFTWARE VERSIONS -------------------------------------------------------------------------------- MCH (current) dsc_8000_23_0_0_nb20230517 (Servicepack) [none applied] MCH (previous) dsc_8000_21_0_3_nb20230118 (Servicepack) RUNNING SOFTWARE VERSIONS (*=update required, ?=update unknown) CARD BUILD SERVICE O/S -SLOT----TYPE------RELEASE-VERSION----PACK-----IMAGE------------CARD STATUS----- -------------------------------------------------------------------------------- -- Chassis 1 -- Slot 1 MCH * 21.0.3 (nb20230118) SP: Slot 14 MCH * 21.0.3 (nb20230118) SP: -- Chassis 2 -- Slot 15 MCH * 21.0.3 (nb20230118) SP: Slot 28 MCH * 21.0.3 (nb20230118) SP: -- Chassis 3 -- Slot 29 MCH * 21.0.3 (nb20230118) SP: Slot 42 MCH * 21.0.3 (nb20230118) SP: -- Chassis 4 -- Slot 43 MCH * 21.0.3 (nb20230118) SP: Slot 56 MCH * 21.0.3 (nb20230118) SP: (p=servicepack is partially applied) Status legend: A - Active, S - Standby, ? - Unknown Select MCH slot number (1 14 15 28 29 42 43 56) to begin upgrade of ISM and SWITCH functions on that MCH. VERSION field modifiers (investigate & update): '***' - a mismatch between the two switches within the MCH. '*!!' - one of the two switches within the MCH is unreachable. Enter slot # or ENTER to cancel: 14
Type "14" and press Enter.
Note: flex_slot.conf file doesn't exist ... This is ok if the SDA is not configured on the system. Software Update for Switch Card in Slot #14 Determining running and current software version. Please wait... Running on SWITCH (slot14_0): -Load: dsc_8000_21_0_3_nb20230118 Current SWITCH version (on MGMT CPU): -Load: dsc_8000_23_0_0_nb20230517 -Servicepack: [none applied] 'u' - Update version (update slot14_0 to match the current load): -Load: dsc_8000_23_0_0_nb20230517 Select action to take, or any other key to cancel: u
Type "u" and press Enter.
avail_switch_current_load is dsc_8000_23_0_0_nb20230517 avail_ism_current_load is Not_Available Running SWITCH software is out-of-date! You have opted to update/reboot slot #14, thereby loading the current software: -Load: dsc_8000_23_0_0_nb20230517 -Servicepack: [none applied] MCH upgrade pre-step: disable TIPC bearer p19p2 for MCH 1. Updating/rebooting switch card in slot #14. Please wait... Note: The switch status may be unavailable for a few minutes while it performs its upgrade procedures. CPU local tftp is enabled. Running SWITCH slot 14 software is now up-to-date. MCH upgrade post-step: enable TIPC bearer p19p2 for MCH 1.
Navigate to Software Revisions, and press Enter.
Select Switch Versions, and press Enter.
AVAILABLE SOFTWARE VERSIONS -------------------------------------------------------------------------------- MCH (current) dsc_8000_23_0_0_nb20230517 (Servicepack) [none applied] MCH (previous) dsc_8000_21_0_3_nb20230118 (Servicepack) RUNNING SOFTWARE VERSIONS (*=update required, ?=update unknown) CARD BUILD SERVICE O/S -SLOT----TYPE------RELEASE-VERSION----PACK-----IMAGE------------CARD STATUS----- -------------------------------------------------------------------------------- -- Chassis 1 -- Slot 1 MCH * 21.0.3 (nb20230118) SP: Slot 14 MCH 23.0.0 (nb20230517) SP: -- Chassis 2 -- Slot 15 MCH 23.0.0 (nb20230517) SP: Slot 28 MCH 23.0.0 (nb20230517) SP: -- Chassis 3 -- Slot 29 MCH 23.0.0 (nb20230517) SP: Slot 42 MCH 23.0.0 (nb20230517) SP: -- Chassis 4 -- Slot 43 MCH 23.0.0 (nb20230517) SP: Slot 56 MCH 23.0.0 (nb20230517) SP: (p=servicepack is partially applied) Status legend: A - Active, S - Standby, ? - Unknown Select MCH slot number (1 14 15 28 29 42 43 56) to begin upgrade of ISM and SWITCH functions on that MCH. VERSION field modifiers (investigate & update): '***' - a mismatch between the two switches within the MCH. '*!!' - one of the two switches within the MCH is unreachable. Enter slot # or ENTER to cancel: 1
Type "1" and press Enter.
Note: flex_slot.conf file doesn't exist ... This is ok if the SDA is not configured on the system. Software Update for Switch Card in Slot #1 Determining running and current software version. Please wait... Running on SWITCH (slot1_0): -Load: dsc_8000_21_0_3_nb20230118 Current SWITCH version (on MGMT CPU): -Load: dsc_8000_23_0_0_nb20230517 -Servicepack: [none applied]
Type "u" and press Enter.
avail_switch_current_load is dsc_8000_23_0_0_nb20230517 avail_ism_current_load is Not_Available Running SWITCH software is out-of-date! You have opted to update/reboot slot #1, thereby loading the current software: -Load: dsc_8000_23_0_0_nb20230517 -Servicepack: [none applied] MCH upgrade pre-step: disable TIPC bearer p19p1 for MCH 0. Updating/rebooting switch card in slot #1. Please wait... Note: The switch status may be unavailable for a few minutes while it performs its upgrade procedures. CPU local tftp is enabled. Connection closed by foreign host.
Execute steps 1 to 10 for each shelf (chassis) if you have a multi-shelf system.
The slot numbers for the MCH cards in a multishelf configuration are as follows:
For more informaiton about the DSC 8000 hardware configuration, refer to DSC 8000 Hardware Description.
If an asterisk appears beside any of the system cards during the verification process, the upgrade for the respective card was unsuccessful. In this case, is recommended that you contact Customer Support.
Start
Make sure the software and OS have been upgraded, all cards are running the same software, and there is no asterisk beside any of the cards.
AVAILABLE SOFTWARE VERSIONS -------------------------------------------------------------------------------- MCH (current) dsc_8000_23_0_0_nb20230517 (Servicepack) [none applied] MCH (previous) dsc_8000_21_0_3_nb20230118 (Servicepack) RUNNING SOFTWARE VERSIONS (*=update required, ?=update unknown) CARD BUILD SERVICE O/S -SLOT----TYPE------RELEASE-VERSION----PACK-----IMAGE------------CARD STATUS----- -------------------------------------------------------------------------------- -- Chassis 1 -- Slot 1 MCH 23.0.0 (nb20230517) SP: Slot 14 MCH 23.0.0 (nb20230517) SP: -- Chassis 2 -- Slot 15 MCH 23.0.0 (nb20230517) SP: Slot 28 MCH 23.0.0 (nb20230517) SP: -- Chassis 3 -- Slot 29 MCH 23.0.0 (nb20230517) SP: Slot 42 MCH 23.0.0 (nb20230517) SP: -- Chassis 4 -- Slot 43 MCH 23.0.0 (nb20230517) SP: Slot 56 MCH 23.0.0 (nb20230517) SP: (p=servicepack is partially applied) Status legend: A - Active, S - Standby, ? - Unknown Select MCH slot number (1 14 15 28 29 42 43 56) to begin upgrade of ISM and SWITCH functions on that MCH. VERSION field modifiers (investigate & update): '***' - a mismatch between the two switches within the MCH. '*!!' - one of the two switches within the MCH is unreachable. Enter slot # or ENTER to cancel:
Execute both of the following procedures in order to upgrade the software on the IO cards.
Upgrade the Software on the IO Cards
Use this procedure if the system contains IO cards. This procedure executes a health check script that verifies the existence of the mp_mtp2.conf.slotX files on the IO card as well as its synchronization to the management CPU card (X is the IO slot number).
Start
Execute the health check script.
health_check_io.sh <IO number>
This command should be executed for each IO.
Prerequisites
Start
Select IO Versions and press Enter.
AVAILABLE SOFTWARE VERSIONS -------------------------------------------------------------------------------- IO (current) AMC348 dsc_8000_23_0_0_nb20230517 OS: rel_12_00_p04.x511.img (Servicepack) [none applied] IO (prev) AMC348 dsc_8000_21_0_3_nb20230118 OS: rel_12_00_p04.x511.img (Servicepack) RUNNING SOFTWARE VERSIONS (*=update required, ?=update unknown) CARD BUILD SERVICE O/S -SLOT----TYPE----------RELEASE-VERSION------PACK-----IMAGE------- -------------------------------------------------------------------------------- -- Chassis 1 -- -- Chassis 2 -- Slot 18 IO AMC348 * 21.0.3 (nb20230118) SP: OS: rel_12_00_p04.x511.img Slot 19 IO AMC348 * 21.0.3 (nb20230118) SP: OS: rel_12_00_p04.x511.img Slot 21 IO AMC348 * 21.0.3 (nb20230118) SP: OS: rel_12_00_p04.x511.img Slot 22 IO AMC348 * 21.0.3 (nb20230118) SP: OS: rel_12_00_p04.x511.img Slot 23 IO AMC348 * 21.0.3 (nb20230118) SP: OS: rel_12_00_p04.x511.img Slot 24 IO AMC348 * 21.0.3 (nb20230118) SP: OS: rel_12_00_p04.x511.img Slot 25 IO AMC348 * 21.0.3 (nb20230118) SP: OS: rel_12_00_p04.x511.img -- Chassis 3 -- -- Chassis 4 -- (p=servicepack is partially applied) Select IO slot number (18 19 21 22 23 24 25) to begin upgrade or decommissioning of individual card(s). Enter slot # or ENTER to cancel: 18
Enter the slot number for the IO card as required (in this example, 18) and press Enter.
You may be prompted for a password from the IO card. To proceed with the upgrade, enter the root password.
Note: flex_slot.conf file doesn't exist ... This is ok if the SDA is not configured on the system. Software Update for IO Card in Slot #18 Determining running and current software version. Please wait... Running on IO (slot18_0): -Load: dsc_8000_21_0_3_nb20230118 -OS: rel_12_00_p04.x511.img Current IO version (on MGMT CPU): -Load: dsc_8000_23_0_0_nb20230517 -OS: rel_12_00_p04.x511.img -Servicepack: [none applied] 'u' - Update version (update slot18_0 to match the current load): -Load: dsc_8000_23_0_0_nb20230517 -OS: rel_12_00_p04.x511.img 'd' - Decommission this IO card to prepare it for removal. Select action to take, or any other key to cancel: u
Enter "u" and press Enter.
avail_switch_current_load is dsc_8000_23_0_0_nb20230517 avail_ism_current_load is Not_Available Running IO software is out-of-date! You have opted to update/reboot slot #18, thereby loading the current software: -Load: dsc_8000_23_0_0_nb20230517 -OS: rel_12_00_p04.x511.img -Servicepack: [none applied] Pushing image to the IO card in slot #18 Executing verify_io_image.sh script on IO board in slot #18 DO NOT INTERRUPT!! THIS MAY TAKE A FEW MINUTES... Done: IO board was already up-to-date Rebooting IO card in slot #18.
Press Enter and return to the main menu.
Repeat steps 1 to 7 for all other IO cards in the system as required.
If an asterisk appears beside any of the system cards during the verification process, the upgrade for the respective card was unsuccessful. In this case, is recommended that you contact Customer Support.
Start
Select IO Versions, and press Enter.
Make sure the software and OS have been upgraded, all cards are running the same software, and there is no asterisk beside any of the cards.
You may be prompted to enter the appropriate password.
AVAILABLE SOFTWARE VERSIONS -------------------------------------------------------------------------------- IO (current) AMC348 dsc_8000_23_0_0_nb20230517 OS: rel_12_00_p04.x511.img (Servicepack) [none applied] IO (prev) AMC348 dsc_8000_21_0_3_nb20230118 OS: rel_12_00_p04.x511.img (Servicepack) RUNNING SOFTWARE VERSIONS (*=update required, ?=update unknown) CARD BUILD SERVICE OS -SLOT-----TYPE--------RELEASE--VERSION-------PACK------IMAGE--------------------- -- Chassis 1 -- -- Chassis 2 -- Slot 18 IO AMC348 23.0.0 (nb20230517) SP: OS: rel_12_00_p04.x511.img Slot 19 IO AMC348 23.0.0 (nb20230517) SP: OS: rel_12_00_p04.x511.img Slot 21 IO AMC348 23.0.0 (nb20230517) SP: OS: rel_12_00_p04.x511.img Slot 22 IO AMC348 23.0.0 (nb20230517) SP: OS: rel_12_00_p04.x511.img Slot 23 IO AMC348 23.0.0 (nb20230517) SP: OS: rel_12_00_p04.x511.img Slot 24 IO AMC348 23.0.0 (nb20230517) SP: OS: rel_12_00_p04.x511.img Slot 25 IO AMC348 23.0.0 (nb20230517) SP: OS: rel_12_00_p04.x511.img -- Chassis 3 -- -- Chassis 4 -- (p=servicepack is partially applied) Select IO slot number (18 19 21 22 23 24 25) to begin upgrade or decommissioning of individual card(s). Enter slot # or ENTER to cancel: