Connecting SBC 5400 Ethernet and Data Cables

This section provides information on connecting media (packet) ports, HA ports, management ports, serial port and alarms ports and installing SFPs.

Installing SFPs

The following SFP transceivers are compatible with

in all Management, Media, and HA ports:

Optionally, MEDIA0 can be used as a single 10G port, with the remaining MEDIA ports empty. The parts for the 10G SFP are:

SFP transceivers must be installed in the Media, Management and HA (if configured for HA) ports of each 

server before making the fiber/copper connections.

• Insert the SFP Gigabit Ethernet LC or SFP Gigabit Ethernet copper RJ-45 transceivers into 
  Unable to show "metadata-from": No such page "_space_variables"
  media ports 0-3, as needed.
• Insert the SFP Gigabit Ethernet LC or SFP Gigabit Ethernet copper RJ-45 transceivers into Management ports 0-3.
• Insert the SFP Gigabit Ethernet LC or SFP Gigabit Ethernet copper RJ-45 transceivers into HA ports 0-1, as needed.

Follow these steps to install SFPs for the first time. To replace an SFP, see the CRU document.

1. Attach an Electrostatic Discharge (ESD) wrist strap (provided in the 
   Unable to show "metadata-from": No such page "_space_variables"
   kit) using the ESD grounding point on the rear panel of the chassis (see Connecting ESD Wrist Strap). 
2. Insert the Sonus-approved SFP transceiver into the desired socket and ensure that the proper orientation when inserting, and that you will hear a click-in when the SFP is seated correctly.
3. Connect/reconnect the fiber optic and/or CAT 5 cables, as appropriate, to media and HA ports.
4. Verify LEDs above the part are flashing indicating link status and data activity.
5. Verify port functionality using the CLI show status system commands once the SBC application software is installed and the system is up and running (for details, see show status systemfrom the 5.0.x documentation).

   1. Verify management and packet port functionality:

      > show status system ethernetPort 

   2. Verify HA port functionality:

      > show status system highAvailabilityPort 

Connecting Serial Port

When connecting a serial cable to the rear serial port of the 

server for communication with a host PC, refer to the figure below for the serial port location.

The following table lists the serial port settings for the host PC.

The DB9 serial cable pin-out is shown below.

Connecting Management Port

To establish the Management port connections, connect the CAT5e cable to the Mgmt 0, Mgmt 1, Mgmt 2, and Mgmt 3 ports. The CAT5e cable may be connected to a switch, router, LAN or WAN as per the customer requirements.

Connecting High Availability Ports

The physical connection between two 

systems consists of a pair of GigE cables (Use the Single mode or Multi mode fiber optic CAT5e cable (NON-CROSSOVER TYPE ONLY), directly connected between each HA ports.

The HA connections provides both box-Level and port-level redundancy system. The HA pair system consists of four management ports; two ports each per system. When a switchover occurs, the logical management address follows the currently active server. For the Media ports, the MAC and IP addresses float (are replicated from active to standby on failover).

Connecting Alarm Ports

The 

ports, allow you to sense (Alarm In) and issue (Alarm Out) external signal. The Alarm Port utilizes a HD15 pin connector and supports 4 output alarms and 2 input alarms. You must create the remainder of the cable, wiring the appropriate sensor or alarm leads to the screw terminator on the connector.

 

The following table lists the Alarm port pin details and their descriptions.

Alarm Out Ports

Each Alarm Out port is a dry relay contact. Each contact will withstand up to 60 volts DC maximum when open, and will carry up to 1 ampere DC maximum when closed.

The following table lists the pin out for the Alarm Out port.

Alarm In Ports

Each Alarm In port is an isolated, current-sourcing sensor which expects to see an external dry contact connection open and close.

For proper operation, the total external load (wiring plus dry contacts) on an Alarm In port must be less than 200 ohms. (Each Alarm In port can source up to 20 milliamperes DC of current maximum, and withstand a voltage drop of up to 7.5 volts DC maximum across an external load.)

The following table lists the pin-out for the Alarm In port.