In this section:

This section provides instructions to perform the actions mentioned above on EdgeMarc devices via the EdgeView. To perform these actions in EdgeView, follow the steps mentioned below:

  1. Choose Devices > List.

    EdgeView Devices Menu

    The EdgeMarc devices list appears.

    EdgeView Devices List

  2. Select the EdgeMarc device on which you want to perform the required action (see EdgeView Devices List image). The device Overview page appears.

    Device Overview Page

    Note

    If a device generates an alarm, a warning icon appears corresponding to that device both in the Device List page and Device Details page.

Apply Collection Policy

Note

Apply Collection Policy is active only when you make changes to the Policy of a Collection (to which the device belongs), or when you move the device to a Collection with a different policy.

Note

Apply Collection Policy is not active for EdgeMarc 300 Series devices as they are ATA devices.


Use Apply Collection Policy to push the new Policy changes to the device.

  1. On the Device Overview page under the ACTIONS menu, select Apply Collection Policy.

    Actions Menu

    You are prompted to confirm this action.

    Confirm the Action

  2. Select CONTINUE to apply to the new policy changes to the device (see Confirm the Action image).

Configure

Note

Configure Device is not active for EdgeMarc 300 Series devices as they are ATA devices.

To configure the selected device, perform the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Configure Device.

    Actions Menu

    The Configure Devices page appears.

    Configure Devices Page

  2. Make the necessary configuration changes (see Configure Devices page image).

    Tip

    You can also push a complete configuration from EdgeView 15 or higher to an EdgeMarc. Select Click to select a file or drag it here to push new configurations to an EdgeMarc.

    Tip

    Refer to Configuring Parameter Values for details with configuring parameter values. 

  3. Schedule when to configure your device by selecting Perform Now or Perform Later. If you decide to perform the configuration later, enter the following details:
    • Schedule Name – Enter a schedule name of your choice.
    • Date and Time – Enter the date and time when the configuration is to be performed.

    • Time Zone – Choose whether time is to be calculated based on Local Time Zone or UTC.

      Schedule Configuration - Perform Later

  4. Once you make necessary changes, select CONFIGURE 1 DEVICE (see Configure Devices page image). You are prompted to confirm configuration changes.

    Confirm Configuration Changes

  5. Select CONFIGURE NOW to configure the selected device (see Confirm Configuration changes image).
Note

If you scheduled this action to be performed at a later point in time, you can edit this action at any point before the scheduled time. To edit, go to Jobs > Scheduled Jobs and click the Edit icon corresponding to this action. For more details on scheduling and editing a job, refer to Scheduling Jobs in EdgeView.

Configure SD-WAN

Note

Configure SD-WAN is not active for EdgeMarc 300 Series devices as they are ATA devices.

To perform SD-WAN configuration, follow the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Configure SD-WAN.

    Actions Menu

    The Configure SD-WAN page appears.

    Configure SD-WAN Screen

  2. Make the necessary configuration changes and then select CONFIGURE SD-WAN ON 1 DEVICE to save the changes (see Configure SD-WAN screen image).

    Tip

    For more details on configuring SD-WAN, refer to Deploying SD-WAN on EdgeMarc Device.

Configure PoE

Note

 This action is available only for Power over Ethernet (PoE) devices.

To configure PoE, perform the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Configure PoE.

    Actions Menu

    The Configure PoE page appears.

    Configure PoE Page

  2. Make the necessary configuration changes (see Configure PoE page image).

    Refer to PoE Configuration Parameter Values to see in detail the PoE configuration parameter values.

  3. Once you make the necessary changes, CONFIGURE POE (see Configure PoE page image). You are prompted to confirm PoE configuration changes.

    Confirm PoE Configuration

  4. Select CONFIGURE NOW to configure PoE (see Confirm PoE Configuration image).

Open Device GUI

To open EdgeMarc device GUI, perform the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Open Device GUI.

    Actions Menu

    A new browser tab opens.

    Enter Login Credentials


    Note

    EdgeView does not support multiple concurrent sessions of Open Device GUI.

Upgrade

To perform the upgrade, follow the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Upgrade Firmware.

    Actions Menu

    The Upgrade Firmware page appears.

    Upgrade Firmware Page

  2. Under the Included Devices table, select the firmware version to which you want to upgrade the device (see Upgraded Firmware page image).

    Tip

    Enable the Send notification once Upgrade is completed check-box if you want to receive notifications.

  3. Schedule when to upgrade your firmware by selecting Perform Now or Perform Later. If you decide to perform the upgrade later, enter the following details:
    • Schedule Name – Enter a schedule name of your choice.
    • Date and Time – Enter the date and time when the upgrade is to be performed.

    • Time Zone – Choose whether time is to be calculated based on Local Time Zone or UTC.

      Schedule Upgrade - Perform Later

  4. Click UPGRADE 1 DEVICE (see Upgrade Firmware page image). You are prompted to confirm upgrade.

    Confirm Upgrade

  5. Select UPGRADE NOW to upgrade the selected device (see Confirm Upgrade image).
Note

If you scheduled this action to be performed at a later point in time, you can edit this action at any point before the scheduled time. To edit, go to Jobs > Scheduled Jobs and click the Edit icon corresponding to this action. For more details on scheduling and editing a job, refer to Scheduling Jobs in EdgeView.

Edit

To edit your device, perform the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Edit Device.

    Actions Menu

    The Edit Device dialog box appears.

    Edit Device Dialog Box

  2. Edit the Name and Description and click SAVE (see Edit Device dialog box image).

Move

To move your device, perform the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Move to Collection.

    Actions Menu

    The Move to Collection page appears.

    Move Devices Page

  2. Choose the collection to which you want to move the selected device (see Move devices page image).

    Tip

    Enable the Send notification once Upgrade is completed check-box if you want to receive notifications.

  3. Select MOVE 1 DEVICE once you chose a collection (see Move devices page image).

Delete

To delete devices, perform the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Delete Device.

    Actions Menu

    The Delete Devices page appears.

    Delete Devices Page

  2. Select DELETE 1 DEVICE to delete the device (see Delete Devices page image). You are prompted to confirm the deletion.

    Confirm Deletion

  3. Select DELETE NOW to delete the selected device (see Confirm Deletion image).

Run Health Report

Note

Run Health Report is not active for EdgeMarc 300 Series devices as they are ATA devices.

To Run Health Report, perform the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Run Health Report.

    Actions Menu

    The Run Health Report page appears.

    Run Health Report Page

  2. Select RUN HEALTH REPORT FOR 1 DEVICE to run health reports (see Run Health Report page image). You are prompted to confirm the health report run.

    Confirm Health Report Run

  3. Click RUN HEALTH REPORT NOW to run the health report (see Confirm Health Report Run image).

Backup

To back up the selected device, perform the following steps:

  1. On the Device Overview page under the ACTIONS menu, select Backup Configuration.

    Actions Menu

    The Backup Configuration page appears.

    Backup Devices Page


    Tip

    Enable the Send notification once Upgrade is completed check-box if you want to receive notifications.

  2. Select BACKUP 1 DEVICE to backup your device (see Backup Devices page image). You are prompted to confirm backup.

    Confirm Backup

  3. Select BACKUP NOW to backup the selected device (see Confirm Backup image).
Note

You can edit this action at a later point in time. To edit, go to Jobs > Scheduled Jobs and click the Edit icon corresponding to this action. For more details on scheduling and editing a job, refer to Scheduling Jobs in EdgeView.

Restore

You can restore your device to a previous backup point using this action. In order to restore your device to a previous backup point, you must have your EdgeMarc device backed up earlier.

Note

You can only restore your EdgeMarc device to available backup points.

To restore the selected EdgeMarc device, perform the following steps:

  1. On the Device Overview page under the ACTIONS menu, select Restore Configuration.

    Actions Menu

    The Restore Configuration page appears.

    Restore Devices Page

  2. In the Included Devices table, choose the backup point to which you want to restore the device (see  Restore Devices page image).

    Tip

    Enable the Send notification once Upgrade is completed check-box if you want to receive notifications.

  3. Select RESTORE 1 DEVICE to backup your device (see Restore Devices page image). You are prompted to confirm the restore operation.

    Confirm Restore

  4. Select RESTORE NOW to restore the selected device (see Confirm Restore image).

Change Passwords

To change the password, perform the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Change Passwords.

    Actions Menu

    The Change Passwords page appears.

    Change Passwords Page

  2. You can change one or all of the following fields (see Change Passwords page image):

      • Root Password
      • GUI User Root
      • GUI User Rouser

    Select Set all as and then Root Password, GUI User Root and/or GUI User Rouser.

    Note

    The password must contain alphanumeric and special characters and should be 6 to 8 characters in length. 

  3. Once you make the necessary changes, click CHANGE PASSWORD FOR 1 DEVICE (see Change Passwords page image). You are prompted to confirm the password change.

    Confirm Password Change

  4. Select CHANGE PASSWORD NOW to change the password(s) of the selected device.

Reboot

To perform a reboot, follow the steps given below:

  1. On the Device Overview page under the ACTIONS menu, select Reboot.

    Actions Menu

    The Reboot Devices page appears.

    Reboot Devices Page


    Tip

    Enable the Send notification once Upgrade is completed check-box if you want to receive notifications.

  2. Click REBOOT 1 DEVICE (see Reboot Devices page image). You are prompted to confirm the reboot.

    Confirm Reboot

  3. Click REBOOT NOW to reboot the selected device (see Confirm Reboot image).
Note

You can edit this action at a later point in time. To edit, go to Jobs > Scheduled Jobs and click the Edit icon corresponding to this action. For more details on scheduling and editing a job, refer to Scheduling Jobs in EdgeView.