In this section:
The T1/E1 PSTN Interface card is a TNV1 compliant digital interface card with integrated Channel Service Unit (CSU) function for direct connection to outside plant wiring. This card has board-mounted protection circuits for electrical isolation and protection against power crossing, lightning surges and hazardous voltages.
Card Port Versions
The T1/E1 PSTN Interface card offers 8 T1/E1 ports; the number of active ports is dependent upon licensing. For more information, see Working with Licenses. The 8-port card is shown below; all T1/E1 ports on the card have identical electrical circuit design.
T1/E1 PSTN Interface 8-port Card
# | Name | Description |
|---|---|---|
1 | Port 1-4 Status | Displays the SBC 2000 T1-E1 PSTN Interface Cards#status of ports 1 through 4. |
2 | Ports 1-4 | Physical ISDN ports 1 through 4. |
3 | Port 5-8 Status | Displays the SBC 2000 T1-E1 PSTN Interface Cards#status of ports 5 through 8. |
4 | Ports 5-8 | Physical ISDN ports 5 through 8. |
5 | Hot Swap | Displays Hot Swap status of the interface card. Unknown macro: {multi-excerpt-include} For more information on inserting and removing interface cards, see Inserting and Removing Interface Cards. |
Port Status LEDs
Each T1/E1 port on the T1/E1 PSTN Interface card has an LED to indicate its operational status. The status states are described below:
Color | Status | Description |
|---|---|---|
Off | No Signal | Indicates the port is not connected or connected cable is not providing a signal. Connect a cable or check the far-end connection. |
Green | Link Up | Indicates the port is operating normally. |
Red | LOF | Indicates the port has a Loss Of Framing (LOF) error. A cable is connected, but the Unable to show "metadata-from": No such page "_space_variables" cannot detect a correct T1 or E1 frame. |
Amber | Yellow | Indicates there is a problem with the far-end connection. This status is usually communicated from remote side and indicates the Unable to show "metadata-from": No such page "_space_variables" receiver is synced up, but there is a problem at the remote side receiver. |
Hot Swap Status LED
Unknown macro: {multi-excerpt-include}
For more information about properly removing an Interface Card, see Inserting and Removing Interface Cards.Dimensions and Weight
| Card | Height mm/in. (PCB only) | Width mm/in. (PCB only) | Height mm/in. (Includes Connector overhang) | Width mm/in. (Includes Connector overhang) | Total Weight (lbs) |
|---|---|---|---|---|---|
| T1/E1 PSTN | 200.0/7.87 | 275.0/10.83 | 249.7/9.83 | 307.5/12.11 | 0.8 |
Environmental Ranges (Operation and Storage)
Environmental Parameter | Specification |
|---|---|
Operating Environmental Conditions | Temperature: 5º to 40º Celsius |
Storage Environmental Condition | Temperature: -40º to 70º Celsius |
T1/E1 Port Pinouts
The T1/E1 ports are connected to the public network using 4-wire shielded 26 AWG or larger twisted pair telecommunication line cords with RJ-48C or RJ-45 connectors.
T1/E1 Port Pinouts
T1/E1 Connector Pinouts
| Pin Number | Description |
|---|---|
| 1 | Receive Ring |
| 2 | Receive Tip |
| 3 | no connection |
| 4 | Transmit Ring |
| 5 | Transmit Tip |
| 6 | no connection |
| 7 | no connection |
| 8 | no connection |
Overview
Content Tools