Network-wide licensing using a site license server (SLS) has been discontinued and is no longer available on SBC 8.0 or later releases.
In this section:
Common Call Statistics Terminology | |
---|---|
Stable Calls | Calls that are established and fully stable (connected and media cut-through type of calls) and will survive a fail-over. This excludes calls in establishing, clearing and updating states which will not survive a fail-over. |
Active Calls | A snapshot of total number of active calls on the SBC at the point of execution of the status command. This count reflects the actual live calls on the box independent of the state of the call (setup, stable, updating or clearing). |
Call Attempts | Accumulative number of attempted calls on this system since the last reboot/start-up, including calls where a setup was sent/received, uncompleted calls (calls failed, busy, not answered, etc.) and calls completed (answered). |
Call Completions | Accumulative number of calls completed on this system since the last reboot/start-up. |
The SBC allows the operator to access data from the current interval and from the interval statistics table related to each object being monitored. The current interval consists of a statistics table entry that is accumulating data for the next interval report. The interval statistics table is a series of statistics table entries containing data from the most recently completed n intervals (where n is the number of intervals in the retention policy configuration).
System
Command Syntax
Below is a high-level view of the command syntax for 'show status system' command.
> show status system activeFileConfig activeRevision admin announcements adSyncStatus baseMacAddress bfdSessionStats configMode coredumpList coredumpSummary cpuUtilCurrentStatistics cpuUtilIntervalStatistics databaseIntegrity daughterBoardStatus dodModeStatus dsbc dspRes dspStatus ethernetPort fanStatus fileStatisticsStatus fipsFSMState haConfig hardDiskStatus hardDiskUsage highAvailabilityPort ipPolicing isOAM jsrcServer ledStatus licenseDomainBundleInfo licenseInfo licenseNodeLockedBundleInfo licenseStatus loadBalancingService logicalMgmtIpInterfaceStatus macAddressStatus mediaProfile memoryUtilCurrentStatistics memoryUtilIntervalStatistics metaVariable mgmtIpInterfaceGroup networkProcessorStatistics niceLicense ntp objectStoreParameters pdcsLicense policyServer powerSupplyStatus savedConfigList sbcliLicense sbcPersonalityStatus security serverAdmin serverSoftwareUpgradeStatus serverStatus softwareUpgradeDetailedStatus softwareUpgradeStatus standbySyncStatus syncStatus systemCongestionCurrentStatistics systemCongestionIntervalStatistics systemCongestionStatus
Command Parameters
The following objects are included in this table for completeness, but only apply when using the
command:clusterAdmin, congestion, daughterBoardAdmin, dspPad, fileStatisticsAdmin, fipsBypassMode, intervalStatistics, licenseRequired, logicalMgmtIpInterface, media, metaVariableDynamic, mgmtStaticRoute, pathCheckPath
MultiExcerpt named Shared Parameters was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
Admin
Command Syntax
> show status system admin <system name>
Command Parameters
Announcements
Announcement file status and statistics.
Command Syntax
> show status system announcements
Command Parameters
MultiExcerpt named Announcements was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
AD Sync Status
Command Syntax
> show status system adSyncStatus
Command Parameters
Daughter Board Status
Command Syntax
> show status system daughterBoardStatus
Command Parameters
MultiExcerpt named Daughter Board was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
DSP
DSP Resources
Command Syntax
> show status system dspRes dspCallCurrentStatistics dspCallIntervalStatistics dspUsageCurrentStatistics dspUsageIntervalStatistics
Command Parameters
MultiExcerpt named DSP Resource was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
DSP Status
This statistic command provides the current number of transcoded sessions per DSP2x slot (
(Refer to DSP Channel Densities for SBC 5400 and 7000 for details).
Command Syntax
> show status system dspStatus dspUsage
Command Parameters
MultiExcerpt named DSP Status was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
Ethernet Port
The SBC 5400 firmware/software is enhanced in 8.0 to add support for one Gbps speeds to the management ports (in addition to the existing 100 Mbps support), including the support of half or full duplex with auto-negotiation on all four management ports. Each management port auto-negotiates the speed/mode independently from other management ports.
Additionally, the SBC Core is enhanced to display the negotiated management port speed and current bandwidth for all management ports from the CLI/EMA.
Since this enhancement allows one Gbps traffic bandwidth for all management ports, it increases the possibility of a traffic overload condition due to the increased bandwidth of the combined management, media and signaling traffic. To address this, the SBC sets the management traffic as the lowest priority. Thus, the system drops the management packets, as necessary, to avoid impacting media or signaling traffic.
Command Syntax
show status system ethernetPort mgmtPortStatus mgmtPortStatus GARNET mgt0 { ifIndex 1; macAddress 0:10:6b:3:da:a5; negotiatedSpeed speed1000Mbps; linkState admnEnabledPortUp; duplexMode full; rxActualBandwidth 0; txActualBandwidth 0; rxPackets 21316; txPackets 1794; rxErrors 0; txErrors 0; rxDropped 183; txDropped 0; } mgmtPortStatus GARNET mgt1 { ifIndex 2; macAddress 0:10:6b:3:da:a6; negotiatedSpeed speed1000Mbps; linkState admnEnabledPortUp; duplexMode full; rxActualBandwidth 0; txActualBandwidth 0; rxPackets 571; txPackets 28240; rxErrors 0; txErrors 0; rxDropped 0; txDropped 0; } mgmtPortStatus GARNET mgt2 { ifIndex 3; macAddress 0:10:6b:3:db:3b; negotiatedSpeed speed1000Mbps; linkState admnEnabledPortUp; duplexMode full; rxActualBandwidth 510; txActualBandwidth 0; rxPackets 456103; txPackets 2839; rxErrors 0; txErrors 0; rxDropped 201; txDropped 0; } mgmtPortStatus GARNET mgt3 { ifIndex 4; macAddress 0:10:6b:3:db:3c; negotiatedSpeed speed1000Mbps; linkState admnEnabledPortUp; duplexMode full; rxActualBandwidth 558; txActualBandwidth 290; rxPackets 326895; txPackets 1263198; rxErrors 0; txErrors 0; rxDropped 0; txDropped 0; } [ok]
Command Syntax
> show status system ethernetPort mgmtAdmin mgmtPortStatus mgmtStatistics packetAdmin packetPortStatus packetStatistics portMonitorStatus portRedundancyGroupStatus
Command Parameters
MultiExcerpt named Ethernet Port was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
License
Command Syntax
> show status system licenseDomainBundleInfo licenseInfo licenseNodeLockedBundleInfo licenseStatus
Command Parameters
The following object only applies to the show table system
command:
licenseRequired
MultiExcerpt named License was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
Network Processor
Command Syntax
> show status system networkProcessorStatistics annStatistics defragStatistics digitStatistics rtcpGenStatistics
Command Parameters
MultiExcerpt named Network Processor was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
NTP
NTP services management
Command Syntax
> show status system ntp peerStatus systemStatus
Command Parameters
The following objects only apply to the show table system
command:
- keys
- serverAdmin
- timeZone
MultiExcerpt named NTP was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
Policy Server
Command Syntax
> show status system policyServer policyServerStatus
Command Parameters
The following objects only apply to the show table system
command:
globalConfig
localServer
policyServerStatus
remoteServer
MultiExcerpt named Policy Server was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
Security
Security management status/statistics details.
Command Syntax
> show status system security ocspProfileUses ocspStatistics pki
Command Parameters
The following objects only apply to the show table system
command:
certExpiryCheck
ipsec
MultiExcerpt named Security was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
Command Examples
To view announcements memory usage:
To view base MAC address:
To view coredump list:
To view Daughterboard status (SBC 7000 example is below):
To view DSP usage:
This example includes several results in the form of <codec>V8Total
or <codec>V8Utilization
. These entries apply if you allowed support for T.38 version 3 (also called V.34 fax transcoding). If you enabled T.38 version 3, you must enable a V.8 signaling detector for all voice codecs.
To view Ethernet Port packet statistics:
To view hard disk usage:
To view systemCongestionIntervalStatistics:
To view system congestion status details.
To view system congestion current statistics.
To view Micro Flow stats:
To display the current HA configuration settings:
To display the D-SBC Sig Port statistics:
To display sync status of active and standby nodes created through a N:1 redundancy group:
To view the status of the Load Balancing Service on S-SBC:
To view the status of the Load Balancing Service on M-SBC: