In this section:
Zone CAC
Command Syntax
Note
Unless annotated otherwise, the parameter values in this section apply to the SBC Core.
% set addressContext <addressContext_name> zone <zone_name> cac bandwidthLimit <0-2147483647, or unlimited> bandwidthLimitThreshold <0-100> bandwidthVideoThreshold <0-100> callLimit <0-2147483647, or unlimited> callLimitThreshold <0-100> egress emergencyOversubscription <0-1000> extendedEmergencyIpLimit <0-40000> hpcOversubscription <0-100> ingress registrationLimit <0-2147483647, or unlimited>
Note
SIP subscription CAC limits are not applied to SUBSCRIBE requests from registered users in access deployments.
Command Parameters
Zone CAC Parameters
Parameter | Length/Range | Description |
|---|---|---|
| 1-23 | The name of the zone. You can configure signaling, media, and control for a zone in the address context. Zone name is unique across all address contexts.
|
cac | N/A | Call Admission Control (CAC) parameters for all peers using this zone. |
bandwidthLimit | 0-2147483647, or unlimited | Total bandwidth limit in Kbps/sec. |
bandwidthLimitThreshold | 0-100 | Bandwidth utilization notification threshold, as a percentage. (default = 0) |
bandwidthVideoThreshold | 0-100 | Enter threshold value (as a percentage of video bandwidth) to limit video streams to a specific bandwidth to prevent video calls consuming call bandwidth otherwise needed for audio calls. (default = 0) |
callLimit | 0-2147483647, or unlimited | Total number of calls allowed on this zone. (default = 'unlimited') |
callLimitThreshold | 0-100 | Call limit utilization notification threshold, as a percentage. (default = 0) |
egress | N/A | Egress-specific call admission control configuration. See Egress Parameters table below for details. |
emergencyOversubscription | 0-1000, or unlimited | This parameter gives priority treatment to emergency calls by specifying the resource over-subscription percentage allowed for emergency calls, and represents the allowed percentage of emergency calls beyond the configured call limit. When the call limit is reached, normal calls are rejected but emergency calls are accepted up to an expanded limit. (default = 10) |
extendedEmergencyIpLimit | 0-40000 | Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
| N/A | Ingress-specific call admission control configuration. See Ingress Parameters table below for details. |
registrationLimit | 0-2147483647, or unlimited | The number of concurrent registrations allowed in this zone. (default = 'unlimited') |
Egress
Command Syntax
% set addressContext <addressContext_name> zone <zone_name> egress callBurstMax <1-900, or unlimited> (SBC 7000 range is 1-2700) callLimit <0-2147483647, or unlimited> callRateMax <1-450, or unlimited> (SBC 7000 range is 1-1350) emergencyOversubscription <0-1000> extendedEmergencyIpLimit <0-40000> hpcOversubscription <0-100> registerBurstMax <1-200, or unlimited> (SBC 7000 range is 1-600) registerRateMax <1-100, or unlimited> (SBC 7000 range is 1-300)
Command Parameters
Egress Parameters
| Parameter | Length/Range | Description |
|---|---|---|
callBurstMax | SBC 5000: SBC 7000: | Maximum allowed burst (above the allowed sustained rate) for egress call attempts, in calls/second. (default = 'unlimited') |
callLimit | 0-2147483647, or unlimited | Total number of outbound concurrent calls allowed. (default = 'unlimited' ) |
callRateMax | SBC 5000: SBC 7000: | Maximum sustained egress call rate allowed in calls/second. (default = 'unlimited' ) You can set both
callRateMax and callBurstMax as “unlimited”; however, if you assign a value to one parameter, the other must also be assigned a value. |
emergencyOversubscription | 0-1000 | Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10) |
extendedEmergencyIpLimit | 0-40000 | Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
registerBurstMax | SBC 5000: SBC 7000: | Maximum allowed burst (above allowed sustained rate) for egress initial SIP registrations. (default = 'unlimited') |
| SBC 5000: SBC 7000: | Maximum sustained egress rate of initial SIP registrations allowed on this zone. (default = 'unlimited') You can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value.
|
Ingress
Command Syntax
% set addressContext <addressContext_name> zone <zone_name> cac ingress callBurstMax <1-900, or unlimited> (SBC 7000 range is 1-2700) callLimit <0-2147483647, or unlimited> callRateMax <1-450, or unlimited> (SBC 7000 range is 1-1350) emergencyOversubscription <0-1000> extendedEmergencyIpLimit <0-40000> hpcOversubscription <0-100> packetRateMax <1-65535, or unlimited> registerBurstMax <1-200, or unlimited> (SBC 7000 range is 1-600) registerRateMax <1-100, or unlimited> (SBC 7000 range is 1-300)
Command Parameters
Ingress Parameters
| Parameter | Length/Range | Description |
|---|---|---|
callBurstMax | SBC 5000: SBC 7000: | Maximum allowed burst (above the allowed sustained rate) for ingress calls, in calls/second. (default = 'unlimited') |
callRateMax | SBC 5000: SBC 7000: | Maximum sustained ingress call rate allowed in calls/second. (default is 'unlimited') You can set both
callRateMax and callBurstMax as "unlimited"; however, if you assign a value to one parameter, the other must also be assigned a value. |
emergencyOversubscription | 0-1000 | Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10) |
extendedEmergencyIpLimit | 0-40000 | Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
packetRateMax | 1-65535, or unlimited | Maximum sustained packet rate allowed in packets/second. (default = 'unlimited') |
registerBurstMax | SBC 5000: SBC 7000: | Maximum burst (above the allowed sustained rate) for initial SIP registrations. (default = 'unlimited') |
registerRateMax | SBC 5000: SBC 7000: | Maximum sustained rate of initial SIP registrations allowed in registrations/second. (default = 'unlimited') You can set both
registerBurstMax and registerRateMax as 'unlimited'; however, if you assign a value to one parameter, the other must also be assigned a value. |
Overview
Content Tools