DO NOT SHARE THESE DOCS WITH CUSTOMERS!
This is an LA release that will only be provided to a select number of PLM-sanctioned customers (PDFs only). Contact PLM for details.
In this section:
This object creates a template for the ISUP signaling services that will be used by the ISUP service group that uses this signaling profile.
On the SBC main screen, go to Configuration > Profile Management > Category: Signaling Profiles > ISUP Signaling Profile.
The ISUP Signaling Profile window is displayed.
To create a new ISUP Signaling Profile, click New ISUP Signaling Profile on the ISUP Signaling Profile List window.
The Create New ISUP Signaling Profile window is displayed.
The following fields are displayed:
Parameter |
|
---|---|
Name | The name of the ISUP signaling group you are configuring. This name must match the strings to be used in the version field of the SIP message header. |
Version Id | The version ID to identify a signaling group. Enter a value in the range of Note:
Version IDs from 0-99 are reserved |
Base Profile | May be specified when configuring a named ISUP signaling profile. The specified base profile is used as a set of defaults for all profile parameter values. Then any parameter for which you explicitly specify a value overrides the default base profile value, in the resulting named signaling profile. |
OLIP Check | Specifies whether or not to support check for the presence of an OLIP when determining that a call is invalid. The options are:
|
Hop Count | The initial Hop Counter value to use (if Hop Count State is enabled). Must be 10-20. |
Hop Count | The state of Hop Counting procedures for this service group:
When Hop Count State is enabled, the following applies:
When Hop Count State is disabled, the following applies:
|
Base Version | Specifies the version of the Base Signaling group from rfc3204. The possible values are:
|
Revision | The ISUP protocol revision that will be supported for this ISUP service:
|
OLIP Check on | When a call with a Charge Number and a Calling Party Number arrives, by default the SBC 5000 series checks for Originating Line Information Parameters (OLIP) and rejects the call if they are not present. This parameter turns OLIP checking off for certain switches that do not supply OLIP information to such calls: |
Network | Specifies whether the network indicator functionality is active. |
Propogation | Specifies whether the propagation delay functionality is active:
|
Look Ahead for | Specifies the default value used in the Look Ahead for Busy field in the ISUP Precedence parameter. |
Network | Specifies the default value used for the 4-digit network identity field in the ISUP Precedence parameter. Must be 0000-9999; default is 0100. |
Generate Japan | Specifies whether to support generating ICS information in SIP MIME case for the signalling group. |
Compatibility | Specifies whether the compatibility is supported for the ISUP Signaling profile |
Access | Specifies whether the access delivery information is active. |
Generic Number | Specifies whether the generic number functionality is active:
|
Generic | Specifies whether the generic notification functionality is active:
|
Generic Digits | Specifies whether the generic digit functionality is active:
|
Location | Specifies whether the location number functionality is active:
|
Originating | Specifies whether the originating ISC point code functionality is active:
|
User Tele | Specifies whether the user teleservice functionality is active:
|
Segmentation | Specifies whether the segmentation functionality is active:
|
Fallback | Specifies whether the fallback functionality is active:
|
E MCID | Specifies whether the EMCID functionality is active:
|
Subscriber | Specifies whether the subscriber priority class functionality is active:
|
APM | Specifies whether the APM is supported for the ISUP Signaling profile.
|
Connected | Specifies if the connected number parameter is supported in the ACM for the ISUP Signaling profile. |
Cause In CPG | Indicates that the cause parameter supported in the CPG for the ISUP Signaling profile. |
Multi Carrier | Specifies whether the multi carrier environment functionality is active. |
Carrier | Indicates that the carrier selection is supported for the ISUP Signaling profile. |
Inr Inf | Specifies whether INR/INF messages are supported. |
CQM CQR | Specifies if the CQM/CQR is supported for the ISUP Signaling profile. |
Call Reference | Indicates that the call reference parameter is supported for the ISUP Signaling profile. |
CFN | Indicates that the CFN is supported for the ISUP Signaling profile. |
Facility | Specifies whether the FAA, FAR, and FRJ messages are supported. |
PAM | Specifies whether the PAM message is supported. |
OBCI ANM | Specifies whether the optional backward call indicators parameter is supported in the |
DRS | Specifies whether the DRS message is supported. |
Redirection | Specifies whether the redirection number parameter is supported. |
LPA | Specifies whether the LPA message is supported. |
UCIC | Specifies whether the UCIC message is supported. |
OLM | Specifies whether the OLM message is supported. |
Blue Book In | Specifies whether the Blue Book parameters are supported in REL for the ISUP Signaling Profile. |
USR | Specifies whether the Blue Book specific parameters are supported in the USR |
BB IAM | Specifies whether the User-To-User indicator parameter is supported in IAM for the |
Call Mod Msgs | Specifies that the CMR, CMA and CMRJ are the call mod messages supported for the ISUP Signaling profile. |
Call Diversion | Specifies whether the call diversion is supported for the ISUP Signaling profile. |
Call History | Specifies whether the call history parameter is supported for the ISUP Signaling profile. |
Generic | Specifies whether the generic reference parameter is supported |
MLPP | Specifies whether the MLPP parameter is supported. |
NSF | Specifies whether the network specific functionality parameter is supported. |
Redirection Number Restriction | Specifies whether the redirection number restriction parameter is supported in ANM, ACM, CPG, and CON messages |
Remote | Specifies whether the remote operations parameter is supported. |
Service | Specifies whether the service activation parameter is supported. |
Signaling | Specifies whether the signaling point code parameter is supported. |
TMR Prime | Specifies whether the transmission medium required prime parameter is supported. |
Transmission | Specifies whether the transmission medium used parameter is supported. |
USI Prime | Specifies whether the user service information prime parameter is supported. |
Redirection | Is the redirection number supported in the ACM for the ISUP Signaling Profile. |
Redirection | Is the redirection number supported in the ANM for the ISUP Signaling Profile. |
Connection Req in FAA | Specifies whether the connection request parameter is supported in the FAA for the |
Connection Req in FAR | Specifies whether the connection request parameter is supported in the FAR for the |
FAC | Specifies whether the FAC message is supported |
Echo Control | Specifies whether the echo control parameter is support. |
Backward GVNS | Specifies whether the backward GVNS parameter is supported for the ISUP Signaling Profile. |
Circuit | Specifies whether the circuit assignment map parameter is supported for the ISUP Signaling profile. |
CCSS | Indicates that the CCSS parameter supported for the ISUP Signaling profile. |
Call Diversion | Specifies whether the call diversion treatment parameter is supported for the ISUP Signaling profile. |
Called In Num | Indicates that the called IN number parameter supported for the ISUP Signaling profile. |
Collect Call | Specifies that the collect call request parameter is supported for the ISUP Signaling profile. |
Conference | Specifies whether the conference treatment parameter is supported for the ISUP Signaling profile. |
Correlation Id | Specifies whether the correlation ID parameter supported for the ISUP Signaling profile. |
Call Offering | Indicates that the call offering treatment parameter is supported for the ISUP Signaling profile. |
Call Transfer | Indicates that the call transfer number parameter is supported for the ISUP Signaling profile. |
Call Transfer reference | Indicates that the call transfer reference parameter is supported for the ISUP Signaling profile. |
Display Information | Indicates that the display information parameter is supported for the ISUP Signaling profile. |
Forward GVNS | Specifies whether the forward GVNS parameter is supported. |
Loop | Specifies whether the LOP message and the Loop Prevention indicators parameter is supported. |
Network | Specifies whether the Network Management Control parameter is supported. |
SCF Id | Specifies whether the SCF ID parameter is supported. |
UID Action IND | Specifies whether the UID action indicators parameter is supported. |
Uid Capability | Specifies the UID capabilities parameter supported for the ISUP Signaling Profile. |
Connected | Specifies the connected number parameter supported in the CPG for the ISUP Signaling |
Generic Number | Specifies the generic number parameter supported in the CPG for the ISUP Signaling Profile. |
Echo Control | Specifies the echo control parameter supported in the IAM for the ISUP Signaling |
Remote Operation In Rel | Specifies the remote operations parameter supported in the REL for the ISUP Signaling Profile. |
Access Transport In Fac | Specifies the access transport parameter supported in the FAC for the ISUP Signaling Profile. |
Generic Notification In Fa | Specifies the generic notification parameter supported for the ISUP Signaling Profile. |
Uuind Anm | Specifies the UUI parameter supported in the ANM for the ISUP Signaling Profile. |
Uuind Cpg | Specifies the UUI parameter supported in the CPG for the ISUP Signaling Profile. |
Nrm Support | Specifies the NRM supported for the ISUP Signaling Profile. |
Cause In Rlc | Specifies the cause parameter supported in the RLC for the ISUP Signaling Profile. |
Upa Upt | Specifies the UPA/UPT supported for the ISUP Signaling Profile. |
Recommendation | Specifies the recommendation field supported in the cause parameter for the ISUP Signaling Profile. |
Transit | Specifies the transiting of unrecognized parameters supported for the ISUP service |
U2u Service | Specifies the level of user to user services supported in the ISUP Signaling Profile. |
Subsequent Address Message | Specifies the Subsequent Address Message supported for the ISUP Signaling |
Forward Transfer Message | Specifies the Forward Transfer Message supported for the ISUP Signaling Profile. |
Special Digits | Specifies the special digits which can appear in dialed digit strings |
Transit Network Selection | Specifies the Transit Network Selection Parameter supported for the ISUP Signaling |
Access | Specifies the Access Transport parameter supported for the ISUP Signaling Profile. |
Jurisdiction | Specifies the Jurisdiction parameter supported for the ISUP Signaling Profile. |
Original Called Number | Specifies the Original Called Number parameter supported for the ISUP Signaling Profile. |
Business Group | Specifies the Business Group parameter supported for the ISUP Signaling Profile. |
Connection Req | Specifies the Connection Request parameter supported for the ISUP Signaling Profile. |
Information Ind | Specifies the Information Indicator parameter supported for the ISUP Signaling Profile. |
Network Transport | Specifies the Network Transport supported for the ISUP Signaling Profile. |
Notification Ind | Specifies the Notification Indicator parameter supported for the ISUP Signaling Profile. |
Redirection Info Acm | Specifies the Redirection Information parameter supported in the ACM message for the ISUP Signaling Profile. |
Egress Service | Specifies the Egress Service parameter supported for the ISUP Signaling Profile. |
Service Code Ind | Specifies the Service Code Indicator parameter supported for the ISUP Signaling Profile. |
Special Process Req | Specifies the Special Processing Request parameter supported for the ISUP Signaling Profile. |
Charge Number | Specifies the Charge Number parameter supported for the ISUP Signaling Profile. |
Transaction Req | Specifies the Transaction Request parameter supported for the ISUP Signaling |
Generic Address Rel | Specifies the Generic Address parameter supported in the REL message for the |
Uu Ind Acm | Specifies the User to User Indicators parameter supported for the ISUP Signaling |
Uu Info | Specifies the User to User Information parameter supported for the ISUP Signaling |
Operator | Specifies the Operator Service Information parameter supported for the ISUP Signaling Profile. |
Cvt Cvr | Specifies the Circuit Validation Test/Response procedures supported for the ISUP Signaling Profile. |
Generic Name | Specifies the Generic Name parameter supported for the ISUP Signaling Profile. |
Redirection | Specifies the Redirection Capability parameter supported for the ISUP Signaling |
Group Redirection Count | Specifies the Group Redirection Count parameter supported for the ISUP Signaling |
Send Two Group Msgs | Sets the Flag to Send Two Group Messages in the ISUP Signaling Profile. |
Await Two Group Msgs | Sets the Flag to Await Two Group Messages in the ISUP Signaling Profile. |
Cqm On Card Swap | Sets the Flag to perform CQM on Card Swap in the ISUP Signaling Profile. |
Ansi95Grs | Specifies the ANSI-95 format for Group Reset Circuit (GRS), which includes optional/ parameters to be used. |
Cpg Before Acm | Specifies a CPG arriving before an ACM be transited. |
Map Dms Fe Parameter | Specifies if the service group should perform mapping of the Completion Code in the DMS FE parameter (ANSI ISUP only) |
Trunk Offering Support | Specifies if the trunk offering messages can, fan, ofr, rcl are supported, at the moment this is just for mexico. |
Operator Selection | Specifies if the operator selection parameter is supported. |
Max Calling Party Digits | Specifies the maximum digit string length for the Calling Party Number parameter supported for this ISUP Signalling Profile. |
Max Called Party Digits | Specifies the maximum digit string length for the Called Party Number parameter supported for this ISUP Signalling Profile |
Free Phone Ind | Specifies the Freephone Indicators parameter supported for this ISUP Signalling Profile. |
Itx Txa | Specifies the ITX and TXA messages supported for the ISUP Signaling Profile. |
Sccp Procedure | Specifies the SCCP Procedure supported for the ISUP Signaling Profile. |
Connection Req In Iam | Specifies the Connection Request parameter supported in the IAM for the ISUP Signaling Profile. |
Ccnr | Specifies the CCNR Possible Indicator parameter supported for the ISUP Signaling Profile. |
Transit Cfn | Specifies the CFN message be transmitted for the ISUP Signaling Profile. |
Holding Ind | Specifies the Holding Indicator be supported for the ISUP Signaling Profile. |
Display Info In Acm | Displays Information parameter in the ACM be supported for the ISUP Signaling Profile |
IAM Generated Carrier Code In Cdr | Should the IAM-Generated Carrier Code always be populated in the CDR for Japan regardless of type. |
Cit Term Exchange Logic | CIT and CAI only in first backward message when terminating exchange |
Check Ixc Against Tlec | • PROTOCOLS - JAPAN |
Unique Transit Cit | • PROTOCOLS - JAPAN |
Transit Received Cit | • PROTOCOLS - JAPAN |
Allow SGDin Generic Digits | Specifies whether SGD parameter (Generic Digits type 25) in mime of SIP-I message is supported or not. The options are:
Note:
If the SGD parameter in the SIP-I mime is to be processed or sent, the Generic Digits needs to be supported as well. Note:
This flag is not applicable when the SBC is configured for ERE mode. |
Set Bci Cdps Based On Sip Call Status | Set this flag to " The options are:
|
Send PRIon RELfor CBWF | Use this flag to send either APM or PRI message with Call Back When Free (CBWF) information on the SIP-I (UK-ISUP) leg during tear down of CBWF call. Refer to Call Back When Free Support feature details. The options are:
Note:
The flag |
Send APPin APMfor CBWF | Use this flag to send CBWF-related APP (ACI=126) in a new APM message. If set to " Refer to Call Back When Free Support feature details. The options are:
Note:
The flag Send APPin APMfor CBWF applies to SIP-I (UK-ISUP variant) only. |
Gr317Charge Number Compliance | Use this flag to check the charge number digit length is in compliance with GR317 which specifies a maximum of 10 digits in IAM message. The
Note:
This flag can only be set to Supported for ANSI ISUP variant. Additionally, the Gr317Charge Number Compliance check only applies to the ISUP MIME sent by the SBC; it does not apply to the ISUP MIME received by the SBC. |
Charge Rate Info For CPC Apc | Use this flag to determine whether the SBC checks for specific payphone-related characteristics in J-ISUP to non-Japanese ISUP calls to trigger using different charge rate information (CRI). The options are:
If set to Supported, the SBC checks for the following conditions:
If a call meets the conditions, the SBC takes charge rate information (CRI) taken from the PSX Charge Rate Profile table specified in the PSX Charge Band Profile associated with the call's ingress trunk group. The CRI is returned in the first backward Address Complete Message (ACM), Call Progress (CPG), or Charging Information (CHG) message during call setup. If the option is set to S If the option is set to Un Supported, the SBC takes CRI values from the PSX Charge Rate Information Parameter table for J-ISUP to non-Japanese ISUP calls and sends them in the first backward ACM, CPG, or CHG message during call setup. Note:
The Charge Rate Info For CPC Apc option is only configurable on Japan-based ISUP Signaling Profiles in which the Revision value specifies either the Nttfcc or Nttcom ISUP variant. |
Cpg Release Timer | Use this timer to specify a time, in seconds, after which the SBC releases a call that has had ANM to CPG message conversion applied. The timer can be set up to 300 seconds. The default is 0. Note:
Values greater than 0 can be configured only on JAPAN-based profiles in which the Revision value specifies either the Nttfcc or Nttcom ISUP variant.
|