Use this object to configure H.323 trunk group parameters.
Command Syntax
% set addressContext <name> zone <name> h323TrunkGroup <TG name>
action <dryUp | force | undefined>
cac
bandwidthLimit <0-2147483647, or unlimited>
bandwidthLimitThreshold <0-100>
callLimit <0-2147483647, or unlimited>
callLimitThreshold <0-100>
egress
callBurstMax <1-200> (SBC 7000 range is 1-2700)
callLimit <0-2147483647>
callRateMax <1-450> (SBC 7000 range is 1-1350)
ingress
callBurstMax <1-200> (SBC 7000 range is 1-2700)
callRateMax <1-450> (SBC 7000 range is 1-1350)
callReservationgroup
inbound <1-100>
incomingCallMinimum <0-128>
outgoingCallMinimum <0-100>
priorityCallMinimum <0-100>
silc
MC1Percent <0-100>
MC2Percent <0-100>
state <disabled | enabled>
state <disabled | enabled>
callRouting
ansSupervisionTimeout <0-1000>
crankBackProfile <name>
respectBearerCapability <disabled | enabled>
dryUpTimeout <1-1440>
ingressIpPrefix <IP address>
media
directMediaAllowed <disabled | enabled>
directMediaGroupId <#>
mediaIpAddress <IPv4 address>
mediaIpInterfaceGroupName <name>
mediaPortRange
baseUdpPort <1024-65534, or "none">
maxUdpPort <1024-65534, or "none">
preAllocateResPad <disabled | enabled>
slowStart <convert | passthru>
sourceAddressFiltering <disabled | enabled>
mode <inService | outOfService>
packetOutage
bandwidthLimitReduction <0-100>
detectionInterval <5-1440>
detectionState <disabled | enabled>
minimumCalls <0-65535>
minimumDuration <0-65535>
parentSharedCacLimitsPoolName <name>
policy
callRouting elementRoutingPriority <ERP profile name>
carrier <serving carrier code>
country <country code>
digitParameterHandling
egressDmPmRule <rule>
ingressDmPmRule <rule>
numberingPlan <numbering plan>
localizationVariant <generic | japan | northAmerica>
media <packetServiceProfile | toneAndAnnouncementProfile>
services classOfService <COS profile name>
signaling ipSignalingProfile <profile name>
qoe
asr
criticalQosAsrLimit <0-70>
defaultQosAsr <0-100>
majorQosAsrLimit <0-90>
clu
criticalQosCluLimit <80-100>
minTimeToProceed <60-3600>
pgrd
criticalQosPgrdLimit <50-10000>
defaultPgrdFactor <50-10000>
rfactor
criticalQosRfactorLimit <0-100>
majorQosRfactorLimit <0-100>
scru
criticalQosScruLimit <80-100>
sendingCompleteEnbloc <disabled | enabled>
services
longDurationCall
ldcAction <noAction | release | trap | trapAndRelease>
ldcEmergencyCalls <exclude | include>
ldcRelCause <Q.850 release value>
ldcTimeout <0, 60-2880>
overlapDialing
minDigitsForquery <integer>
overlapState <disabled | egressOnly | enabled | ingressOnly>
state <disabled | enabled>
// Mandatory parameters:
h323TrunkGroup
action
dryUpTimeout
ingressIpPrefix
mode
sendingCompleteEnbloc
state
// Non-mandatory parameters:
cac
callReservation
callRouting
media
packetOutage
parentSharedCacLimitsPoolName
policy
qoe
services
Command Parameters
Zone H.323 Trunk Group Parameters
Parameter | Description |
---|
action | Action when putting this H.323 trunk group outOfService. This object controls whether calls are forced off or allowed to dryup upon a mode out-of-service. dryup (default)force undefined
|
cac | Call admission control parameters for this H.323 trunk group. Specify the following CAC parameters: bandwidthLimit – Total media bandwidth limit (in K bits/sec). (range: 0-2147483647, or unlimited / default is ‘unlimited’).bandwidthLimitThreshold – Bandwidth limit notification threshold, as a percentage. (range: 0-100 / default = 0)callLimit – Total number of either ingress or egress concurrent calls allowed. (range: 0-2147483647, or unlimited).callLimitThreshold – Call limit notification threshold, as a percentage. (range: 0-100 / default = 0)egress – Egress-specific call admission control configuration.callBurstMax – (Default is 'unlimited') Maximum allowed burst (above the allowed sustained rate) for egress call attempts in calls/second. (range: 1-200, or unlimited. SBC 7000 range is 1-2700, or unlimited).callLimit – Total number of concurrent calls (either ingress or egress) allowed on egress. (range: 0-2147483647, or unlimited / default is “unlimited”).callRateMax – (Default is 'unlimited') Maximum allowed burst in calls/second (above the allowed sustained rate) for egress call attempts. (range: 1-450, or unlimited. SBC 7000 range is 1-1350, or unlimited).
ingress – Specifies the ingress-specific call admission control configuration. Specify the following ingress parameters:
NOTE: You can set both “callBurstMax” and “CallRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. NOTE: Cal policing using callRateMax and callBurstMax is applicable only to normal and emergency calls, not to high priority calls (HPC). |
callReservation | Parameters for reserving a portion of the resources for specific call direction or type for this H.323 trunk group. inbound – Percentage of callLimit reserved for handling inbound calls. This is the percentage of channels reserved for handling inbound calls. Default is 0%. Percentage selection allowed in 5% increments. Enter value in 5% increments. (range: 0-100).incomingCallMinimum – Minimum number of incoming call allowed when reservations are enabled for this trunk group. Enter value in range of 0-128. Default is 1.outgoingCallMinimum – Minimum percent of outgoing call allowed when reservations are enabled for this trunk group. Enter value in range of 0-100. Default is 10.priorityCallMinimum – Minimum number of priority call allowed when reservations are enabled for this trunk group. Enter value in range of 0-100. Default is 1.silc – The SILC traffic control configuration.MC1Percent – Percentage of calls to accept when the machine congestion level is 1. (range: 0-100 / default = 75).MC2Percent – Percentage of calls to accept when the machine congestion level is 2. (range: 0-100 / default = 25).state – Administrative state to enable/disable the SILC traffic control. Select any one of the option: disabled or enabled.
state – Administrative state to disable or enable the call reservation feature on a H.323 trunk group.
|
callRouting | Call routing parameters are listed below.
ansSupervisionTimeout – Configure this parameter on the ingress trunk group specifying the timeout period (in seconds) for the egress trunk group to receive the first backwards message from the called party exchange (SIP 180 - “Ringing" and SIP 183 - “Progress") until the call is answered. If the timeout period expires, the answer supervision action specified is triggered. A value of "0" disables this timer (range: 0-1000 / default = 300).crankBackProfile – Name of the crank back profile.respectBearerCapability – Enable flag to accept the Bearer Capability Information element values unchanged from H.225 SETUP.disabled (default)enabled
|
dryUpTimeout | Timeout value (in minutes) for the dry up action. (range: 1-1440 / default = 5). |
ingressIpPrefix | Ingress peers matching these ingress IP prefixes are assigned to this H.323 trunk group. Up to 128 ingressIpPrefix entries may be assigned to a H.323 trunk group. Enter IPv4 or IPv6 address in the following format:<IPv4 or IPv6 address > – The V4 IP address is in dotted decimal form (for example, 128.127.50.224). The V6 IP address is in hexadecimal/colon form (for example, 1280:1276:3350:2224:2222:3333:8888:1245 or ffd00:21:445:128::7880). (default is 0:0:0:0:0:0:0:0).<prefixLength> – The number of bits of address which form the network part of the IPv6 address. Rest of the bits (128 – prefix length) specify the host part of the IPv6 address. Must be 0-128.
|
media | Specifies the parameters associated with media features for this H.323 trunk group. Specify the following media parameters: NOTE: When provisioning a UDP media port range, set the range slightly larger than the actual number of ports needed to support maximum simultaneous calls. NOTE: Because video is only supported for H.323-H.323 Slow Start calls, use passthru option in this scenario. |
mode | Specifies the operational mode of this H.323 trunk group. inService outOfService (default)
|
packetOutage | Packet outage detection parameters for this H.323 trunk group. bandwidthLimitReduction – Amount to reduce the bandwidth limit (as a percentage of configured limit) when a packet outage is detected. (range: 0-100 / default =50.detectionInterval – The size of the packet outage detection interval in minutes. (range: 5-1440 / default = 15).detectionState – Enable this flag to perform automatic bandwidth reduction when a packet outage is detected.disabled (default)enabled
minimumCalls – The number of calls with outages required within the current interval to declare a packet outage event (range: 0-65535 / default = 1000).minimumDuration – Minimum outage (in milliseconds) on a call for that call to be counted as part of the packet outage detection algorithm. (range: 0-65535 / default = 6000).
|
parentSharedCacLimitsPoolName | Name of existing shared CAC pool. |
policy | Specifies the policy data for this H.323 trunk group. callRouting – Specifies the parameters and controls used for routing a call or request to the next-hop entity.elementRoutingPriority – The Element Routing Priority table indicates what Call Processing Elements types (including "none") should be used to determine matching routing table entries. Routing table lookups are attempted in priority order for all matching Call Processing Element types until a match is found. Different Element Routing Priority profiles can be associated with different (ingress) trunk groups. If no Element Routing Priority table is explicitly associated with a trunk group, the DEFAULT_IP Element Routing Priority profile is used.
carrier – Specifies the parameters and controls used for carrier for this trunk group for this H.323 trunk group.country – Specifies the parameters and controls used for country for this H.323 trunk group.digitParameterHandling – Specifies the parameters and controls used for digit parameter handling for this trunk group for this H.323 trunk group. Options are:
egressDmPmRule – The name of the Digit Manipulation/Parameter Manipulation profile applied at the egress.PAI_AND_FROM_HEADER PAI_DISPLAY_NAMES_1_NTL PAI_SIP_DSPNAME_CLG_NAM PAI_TEL_DSPNAME_GN_CPN PRFX_TO_HEADER_CDPN_NTL PRFX_TO_HEADER_GDPN_NTL PRFX_TO_HEADER_OCN_NTL SIP_ADD_PLUS SIP_REMOVE_CLG81 SIP_REMOVE_PLUS1 SIP_REMOVE_PLUS39 SIP_REMOVE_PLUS44 SIP_REMOVE_PLUS49 SIP_REMOVE_PLUS52 SIP_REMOVE_PLUS81 SIP_REMOVE_PLUS86 SIP_REMOVE_PLUS91
ingressDmPmRule – The name of Digit Manipulation/Parameter Manipulation profile applied at the ingress.PAI_AND_FROM_HEADER PAI_DISPLAY_NAMES_1_NTL PAI_SIP_DSPNAME_CLG_NAM PAI_TEL_DSPNAME_GN_CPN PRFX_TO_HEADER_CDPN_NTL PRFX_TO_HEADER_GDPN_NTL PRFX_TO_HEADER_OCN_NTL SIP_ADD_PLUS SIP_REMOVE_CLG81 SIP_REMOVE_PLUS1 SIP_REMOVE_PLUS39 SIP_REMOVE_PLUS44 SIP_REMOVE_PLUS49 SIP_REMOVE_PLUS52 SIP_REMOVE_PLUS81 SIP_REMOVE_PLUS86 SIP_REMOVE_PLUS9
numberingPlan – The name of the Numbering Plan profile.CHINA_NUM_PLAN GENERIC_NUM_PLAN GERMANY_NUM_PLAN INDIA_NUM_PLAN ITALY_NUM_PLAN JAPAN_NUM_PLAN MEXICO_NUM_PLAN NANP_ACCESS UK_NUM_PLAN
localizationVariant – Localization variant options for this H.323 trunk group.media – Parameters associated with media policy for this H.323 trunk group.packetServiceProfile – Packet service profile name.toneAndAnnouncementProfile – Tone and announcement profile name.
services – Identifies enhanced services and features for this H.323 trunk group. Current option:classOfService <CoS name>.
signaling – SIP signaling for this H.323 trunk group.ipSignalingProfile <IPSP name>
|
qoe | Signaling and media Quality of Experience configuration. asr – ASR signaling quality measurement.criticalQosAsrLimit – The critical ASR limit below which call admission is stopped. (range: 0-70 / default = 40).defaultQosAsr – Default value used by ASR when no calls are made during a sampling period (rnage: 0-100 / default = 90).majorQosAsrLimit – The major ASR limit below which call admission is reduced. (range: 0-90 / default = 70).
clu – Call Limit Utilization (CLI) signaling quality measurement.criticalQosCluLimit – Critical limit (in percentage) above which all calls are dropped on specified peer/trunk group. (range: 80-100 / default = 80).
minTimeToProceed – The minimum time period (in seconds) before call admission starts after any trunk group KPI falls below the critical threshold. (range: 60-3600 / default = 60).pgrd – Post Gateway Ringing Delay (PGRD) signaling quality measurement. Options:criticalQosPgrdLimit – The critical PGRD limit (in milliseconds) above which the call admission is stopped. (range: 50-10000 / default = 1000).defaultPgrdFactor – Default value to be used as PGRD when no calls are made for a sampling period. (range: 50-10000 / default = 1000).
rfactor – R-Factor signaling quality measurement.criticalQosRfactorLimit – The critical R-Factor limit below which call admission is stopped. (range: 0-100 / default = 50).majorQosRfactorLimit – The major R-Factor limit below which call admission is reduced. (range: 0-100 / default = 70).
scru – Sustained Call Rate Utilization signaling quality measurement.criticalQosScruLimit – Critical limit (in percentage) above which all calls are dropped on specified peer/trunk group. (range: 80-100 / default = 80)
|
sendingCompleteEnbloc | Use this flag to disable/enable sending a complete called party number in a single enbloc SETUP message. disabled (default)enabled
|
services | Parameters associated with advanced services and features for this H.323 trunk group. longDurationCall – Defines long duration call supervision. Parameters include:ldcAction – Action to take if the long duration call timer expires: noAction | release | trap | trapAndRelease -
ldcEmergencyCalls – Flag to include/exclude Emergency Calls in/from Long Duration Call Disconnect procedures.
ldcRelCause – Q.850 release value to use should the call be released due to long duration call timer expiry. (default = 41).ldcTimeout – Timeout value (in minutes) of the long duration call timer. Options:0 – Use to disable the timer (default).60-2880 – Sets timer to specified value.
overlapDialing – Specifies the Overlap dialing parameters.minDigitsForQuery – Controls the number of called address digits to collect before performing the first policy query during overlap receiving. If set to “0”, this parameter is irrelevant in controlling policy query. (Range: 0-30 / default = 0)overlapState – Control to determine if Overlap Dialing is supported.disabled (default)egressOnly – Select to enable egress overlap dialing only for a trunk group +both egress and ingress.enabled – Select to enable overlap dialing. If the trunk group is being used for both ingress and egress, then both directions are enabled.ingressOnly – Select to enable ingress overlap dialing only for a trunk group using both egress and ingress.
|
state | The administrative state of the H.323 trunk group. disabled (default)enabled
|