In this section:

 

 

HTTPS Support

The EMA GUI is available via TLS-secured (https) access either directly through port 443 or indirectly through port 80 to 443. ACL rules are not applicable to prevent unsecured (http) access.

A sample X.509 certificate, which is a copy of the BMC and the EMA Platform Mode certificate, is shipped along with the SBC shipment. The size of this certificate is 2,000 bytes.

Note

The BMC is not applicable to SBC SWe.

The EMA uses the common Local Cert store of the SBC Core (used also for SIP/TLS) rather than having its own separate certificate store. The operator may replace that sample certificate at any time. The replacement mechanism is implemented with post installation/upgrade scripts.

Certificates with RSA keys up to 4,096 bits are supported.

Note

Sonus recommends using only 2,048 bit certificates with release 3.1 and discourages the use of 4,096 bit certificates in 3.1 due to anticipated upgrade issues with the current software.

Enter the following URL in the browser to access the SBC EMA:

https://<hostname>

where <host name> is one of the management IP addresses of the SBC, or the equivalent DNS name. For example, https://10.54.41.8.

EMA uses a self-signed certificate which may produce a warning message from Internet Explorer and Firefox. These messages may be ignored.

Note

The SBC Core is delivered with sample self-signed X.509 certificates. Be aware that even though these sample certificates will allow you to use HTTPS to access the SBC from EMA, BMC and EMA Platform Mode interfaces, using this protocol with the sample certificates is not a truly secure access method. If your organization requires more secure access, refer to Generating PKI Certificates.

Note

The SBC Core supports SHA-256 for certificate verification.

Logging In

Supported Browsers and Client Computers

Refer to 

Supported Browsers and Client Computer Requirements
for a list of supported browsers and client platforms for accessing EMA.

Procedure

To log into the Embedded Management Application (EMA):

  1. Launch your web browser.
  2. Enter the SBC EMA URL <ip address/device name> 

    Note

    When using Internet Explorer/Mozilla Firefox browser, a website security issue may prevent you from going directly to the SBC application login screen, as shown in example below.

    Certificate Security Error

  3. Click Advanced.

    Firefox Message - Self-Certified Website

  4. Click Add Exception

    Firefox Message - Add Security Exception

  5. Uncheck the Permanently store this exception check-box and click Confirm Security Exception.  The Login window appears as shown below. 

    Login

  6. Enter your Username and Password. Your username and password will be supplied along with the SBC installation package. Once you have successfully logged into the SBC, your temporary password expires and you are prompted to change your password.

Note

This change password screen appears only for the first login of the new user.

Change Password


Ensure your new password meets the following criteria:

      • Minimum length of characters is 8.
      • Minimum number of upper case characters is 1.
      • Minimum number of lower case characters is 1.
      • Minimum number of numeric digits is 1.
      • Minimum number of special characters is 1.
      • Maximum number of consecutive repeating characters is 3.
      • Minimum number of differences compared to the old password is 4.
      • Do not repeat any of the last 4 passwords.

7. Once your password is successfully changed, enter your username and new password on the Login screen and click Log In.

Note
  • You can also change the password in EMA without logging in to the application. The option to change password is available on the SBC Application login screen.
  • Your username and password are same as that for the CLI.

Last Login Information 

 When a user logs into either the CLI or EMA, information on the last successful and failed login attempts is displayed. The information shown includes:

  1. Last successful login date and time.
  2. Last successful login IP address.
  3. Last unsuccessful login date and time.
  4. Last unsuccessful login IP address.
  5. Number of failed attempts after successful login.

     

Note

Items 3, 4 and 5 display only when the last successful login date is older than the last unsuccessful login date. See the figure Login Message - Previous Unsuccessful Attempts. 

Note

The Last Login Information also displays for a new user for the first login. The new user is first authenticated and then allowed to change the system-generated password. 

Configuring a Banner in the Login Screen

  1. On the main screen, navigate to Admin > Application Management. Click Banner chiclet on the left hand side of the page to display the Configure Login Banner window.
  2. Enable Show Login Banner option. You can request the user to acknowledge the Banner by enabling the Require User to Acknowledge Banner before Logging in option and also, you can request the user to acknowledge every time they login or only during the first login.
  3. Add your banner text in the text box next to Banner Text option to display your Banner content.
  4. Click Save to save your edits.

Logging Out of EMA

To log out of EMA:

Hover the mouse pointer over <your_username> on the menu bar. and click Log Out.

Log Out

Security Enhancement to Allow Only One Concurrent EMA Session

This security enhancement is available beginning with SBC Core version 06.02.00R000.

This enhancement enables the EMA application (including EMA in platform mode) to disable concurrent user sessions. Once a new session is established, any existing session is terminated immediately. When an EMA user attempts to log in, the system checks for any open sessions with the same username. If any existing user session is identified, that user is immediately logged out from the application and allows the new user to log in to the system.

Note

This feature is applicable to all EMA users (local users, radius users, PKI certificate-based users, and CAC users). 

  • No labels