You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Next »

In this section:

Related articles:

 The Admin object allows you to configure the system administration related parameters in the 

Unable to show "metadata-from": No such page "_space_variables"
. You can configure audit log state, system location, IP version used, and other parameters.

To View Admin

On the

Unable to show "metadata-from": No such page "_space_variables"
 main screen, go to All > System > Admin.

The Admin window is displayed.

All - System - Admin

 

To Edit Admin

To edit any of the Admin in the list, click the radio button next to the specific Admin name.

All - System - Admin Highlighted

 

The Edit Selected Admin window is displayed below.

All - System - Admin Edit Window

 

 

The following fields are displayed:

All - System - Admin parameters

 

Parameter

Description

Name

Specifies the name of the

Unable to show "metadata-from": No such page "_space_variables"
system.

Location

Specifies the physical location of the

Unable to show "metadata-from": No such page "_space_variables"
system.

Contact

Specifies the contact information of the

Unable to show "metadata-from": No such page "_space_variables"
system.

Local Authentication Enabled

Specifies the confd CLI user information stored locally can be used for authentication.

External Authentication Enabled

Specifies the confd CLI user information stored on remote Radius Server used for authentication.

Util Monitor Stats Interval

Specifies the time interval for system resource monitoring statistics. The value ranges from 5 to 60 minutes and the default value is 15 minutes.

Note:  

If using the EMS in your network, configure EMS PM data collection intervals for the

Unable to show "metadata-from": No such page "_space_variables"
to be both:

  • Equal to or greater than the
    Unable to show "metadata-from": No such page "_space_variables"
    interval size, and
  • Not less than the
    Unable to show "metadata-from": No such page "_space_variables"
    interval size multiplied by the
    Unable to show "metadata-from": No such page "_space_variables"
    number of intervals.

See Insight User Guide for configuration details.

Util Monitors Stats Num of Past Interval

Specifies the number of past intervals saved by the system resource monitoring statistics.

Audit Log State

Specifies the state of the management audit log. The options are:

  • enabled
  • disabled

Dsp Mismatch Action

Specifies the action to take for one of the following DSP Mismatch conditions:

  1. Mismatch in DSP card installation across any/all slot locations: Cards must match by slot location. For any mismatched slot, DSP capacity is not used when "preserveRedundancy" is configured (and card dried up if calls were already in place when the mismatch occurred), or card is left unprotected when "preserveCapacity" is configured.
  2. Mismatch in DSP card type within as lot location: Card installations must match by type – DSP25 (higher capacity) or DSP20 (lower capacity). Same rules as above apply.

The options are:

  • preserveRedundancy (default): The Active automatically triggers a graceful dry-up in an attempt to align DSP hardware capabilities. Once dry-up completes, the Active
    Unable to show "metadata-from": No such page "_space_variables"
    uses the protected, matching DSP capacity to preserve redundancy.

Note: During the dry-up period, active calls using the higher Capacity DSPs are not protected in the event that a switchover occurs before the dry up completes.

  • preserveCapacity: The Active
    Unable to show "metadata-from": No such page "_space_variables"
    continues to use the extra DSP capacity, as needed, assuming appropriate session licenses are in place; partial redundancy is in effect.

Note: If a switchover occurs, calls using the higher capacity DSPs on Active are not protected during switchover (i.e. partial redundancy).

Cli Set Warning Support

Specifies whether to enable warning prompts configured for the Set commands or not. The options are:

  • enabled (default)
  • disabled

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

Admin Commands

Specifies all the admin commands used and its purpose.

All - System - Admin Commands

 

The following options are displayed:

Admin Commands parameters

 

Parameter

Description

Re Generate Ssh Rsa KeysSpecifies that it causes regeneration of all SSH keys.

Re Key Confd Encryption Key

Specifies that it causes encryption keys used by the system configuration database to be regenerated.

Note: Sonus recommends backing up current encrypted parameters in plaintext, if possible.  Sonus further recommends performing a full configuration backup immediately after this activity has successfully completed.

Remove Saved Config

Remove the saved configuration from the system.

  • fileName – Specify filename of configuration to remove from the system.
RestartThis command restarts a server/CE.
Set Ha Config

Use this action command to configure the

Unable to show "metadata-from": No such page "_space_variables"
for Geographical Redundancy High Availability (GRHA) mode when active and standby servers are located in two different data centers to protect
Unable to show "metadata-from": No such page "_space_variables"
s against data center and network failures. To configure/change just one setting, use currentValue option for the other setting.

  • bondMonitoring – Select the bond monitoring type for GRHA mode.
    • currentValue 
    • direct-connect
    • network-connect
  • leaderElection Select the leader election algorithm type to use for GRHA mode.
    • currentValue 
    • enhanced
    • standard

Note: Geographical Redundancy High Availability (GRHA) is not supported on SBC SWe Cloud.

Refer to:

Soft ResetRestart the applications on the system without rebooting the server(s).
SwitchoverPerform a switchover of the management applications and restart all applications on currently active server.
Verify Database Integrity

Use this command to verify that the

Unable to show "metadata-from": No such page "_space_variables"
policy and configuration databases on the active server are in sync and that the policy databases on the active and standby servers are in sync. Because these commands take a few seconds to execute, it is not advisable to constantly run these commands on systems.

  • activeAndStandbyPolicy – Check if policy databases on the active and standby servers are in sync.
  • activeConfigAndActivePolicy – Check if the policy and configuration databases on the active server are in sync.
  • all – Perform both of the above checks.

Zeroize Persistent Keys

Use this control to securely erase all persistent CSPs from the system. The

Unable to show "metadata-from": No such page "_space_variables"
server reboots after confirmation.

  • No labels