DTMF and RTP Relay

SIP DTMF Trigger Detection

The SIP Dual-Tone Multi-Frequency (DTMF) trigger detection and notification functionality enables the SBC Core to look for specific DTMF trigger patterns across the packet network, and to notify an external SIP entity when such patterns are detected. If a mid-call trigger is configured for a call, it is activated as soon as the call is connected. When the SBC detects DTMF input matching the pattern criteria of the trigger, it sends the DTMF input in a SIP INFO message to the SIP call peer with content type application/DTMF.

The SBC Core supports the following methods of relaying DTMF digits for transcoded calls:

• In-band—Leaves the DTMF tones in-band as encoded audio.
• Out-of-band—Carries DTMF in the signaling protocol (SIP or H.323).
• RFC 2833—Encodes DTMF into RTP using a format and Payload Type (PT) distinct from the audio encoding. The SBC supports up to five DTMF payloads bound to different clock rates if the SIP Trunk Group services flag honorSdpClockRate is enabled (Refer to SIP Trunk Group - Services - CLI or Trunk Group - SIP Trunk Group (EMA) page for configuration details.).

DTMF Interworking

The SBC also supports interworking between different DTMF Relay methods. For packet-to-packet calls both signaling and media (bearer) traffic flow through the SBC (whether or not media transcoding is also employed). For signaling traffic, the SBC inherently provides address and port mapping between the addresses used within the carrier's own network and those “visible” to the peering partner.

The SBC includes two seeded DTMF trigger profiles:

• Ingress—Applied to the calling (ingress leg) side.
• Egress—Applied to the called (egress leg) side.

To enable this feature, configure and enable the SBC DTMF trigger for the appropriate leg of the call. Changes to configuration parameters do not affect existing calls.

To configure via CLI, use following syntax:

% set profiles dtmfTrigger <egress | ingress> interdigitTimeout <timeout_value> longdigitDuration <longdigitDuration> pattern <trigger_pattern> state <enabled | disabled>

Below is a CLI example of enabling DTMF interworking for PSP "profile1" with transcoding.

set profiles media packetServiceProfile pprfile1 packetToPacketControl conditionsInAdditionToNoCommonCodec differentDtmfRelay enable
commit

Refer to DTMF Trigger - CLI, Packet Service Profile - CLI or Dtmf Trigger Profile - Dtmf Trigger, Packet Service Profile - Flags, Packet To Packet Control - Condition In Addition To No Common Codec (EMA) for configuration details.

DTMF Interworking Without DSP

The SBC supports interworking between RFC2833/RFC4733 and out-of-band DTMF methods without using DSPs. Below is a CLI example of enabling DTMF interworking for PSP "profile1" without transcoding.

% set profiles media packetServiceProfile profile1 flags digitDetectSendEnabled enable
% set profiles media packetServiceProfile profile1 flags interworkDtmfWithoutTranscoding enable

Refer to Packet Service Profile - CLI or Packet Service Profile - Flags (EMA) for configuration details.

SIP RTP Relay

To preserve the privacy and security model for media flows as well, the SBC implements an RTP Relay. In RTP Relay, the call endpoints send media packets to an address/port on the SBC. As the media packets flow through the SBC, the source and destination addresses are changed such that the SBC is itself always one of the endpoints in each call leg. Thus, the carrier's internal addresses are not exposed to the peering partner, and inbound media flows are directed only to a limited set of well-defined SBC addresses for security filtering purposes.
 

 Figure "SIP IP Pipe Example" below depicts the two SIP IP "pipes" used by the SBC:

• The SIP Signaling Channel exchanges call signaling packets with a SIP Application Server (AS).
• The IP Media Stream exchanges call data with a SIP Media Server (MS), IAD or SIP phone.

SIP IP Pipe Example

The SIP Application Server manages the SIP MS/IAD/phone through the IP cloud, shown by the dotted line in Figure 1 . This interaction is logically removed from the SIP SBC software and hence is not annotated in the following examples.

Audio call data may be encoded according to any of the algorithms below for delivery through the IP Media Stream:

• G.711
• G.711 with Silence Suppression
• Cloned encoding algorithms
• Isolating the tones and designating them explicitly within the IP Media Stream
• Isolating the tones, then designating and delivering them explicitly on the SIP Signaling Channel instead of the IP Media Stream

The IP Media Stream uses the Realtime Transport Protocol (RTP) to deliver call data for all audio compression algorithms.

Short Duration RTP Inactivity Timer for Emergency Calls

The SBC supports RTP/RTCP Media inactivity monitoring with a system wide configuration of silence detection duration from 20 to 1260 seconds. Along with the system wide configuration, Ribbon provides additional configuration support for shorter RTP inactivity duration of 0 to 1260 seconds in the Packet Service Profile (PSP) of the PSX for specific zone usages during emergency calls such as 911 calls. 

When media inactivity is detected on a call, the SBC takes the configured action on a call such as disconnecting, raising a trap or alarm, and so on. 

On the PSX Manager > Packet Service Profile screen, the field "Media Peer Inactivity Timeout (s)" allows the operator to reduce the timeout duration to 0-1260 seconds for specific zones during emergency calls such as 911 calls. By default it is set to 0 (disabled). The value set on the PSX Manager takes precedence over the value set on the SBC side. When the field "Media Peer Inactivity Timeout (s)" on the PSX is set to 0 (disabled), the SBC uses the configuration value set on the SBC CLI (Media System - CLI) or SBC EMA screen (System - Media - Media Peer Inactivity).

Audio Stream Examples Using DTMF

KPML DTMF Support

Overview

The Key Press Markup Language (KPML) functionality enables the SBC to look for DTMF trigger patterns and to notify an external SIP entry when such patterns are detected. When there is a SUBSCRIBE with a KPML event, the SBC SIP Front End (SIPFE) matches the KPML dialog event parameters and also determines which SIP Signaling Group is hosting this SUBSCRIBE event. The SUBSCRIBE event is then sent to the correct SIP Signaling Group and the XML/KPML document is parsed. This action gives the SIP Signaling Group enough information to send a digit map pattern to the Node Resource Manager Agent (NRMA). If the digit pattern matches, the NRMA send a message back to SIP Signaling Group about the matched digit pattern. Once the digit pattern is matched, the SIP Signaling Group is able to send SIP NOTIFY message to the awaiting SIP client.

There are two types of subscriptions that the KPML recognizes:

• One-Shot Subscription: The one-shot subscription occurs once and terminated after a pattern match occurs and a report is sent in a NOTIFY message. The "Subscription-State" in the NOTIFY message is set to "terminated".
• Persistent Subscription: The persistent subscription remains active even after the pattern match occurs.
  There are two sub-types:
  • Continuous Notify: The User Interface (UI) sends a NOTIFY message whenever a user input matches a subscribed pattern.
  • Single Notify: The UI sends a NOTIFY message whenever a user input matches the first subscribed pattern. There are no NOTIFY messages until the SBC receives a new subscription request on the subscription dialog.

Support of KPML Events via In-Dialog Subscribe

Previously, all Out-Of-Dialog (OOD) Subscribe messages were consumed by the SBC, and all In-Dialog Subscribe messages are relayed by the SBC. The SBC Core is enhanced to control how the SBC manages Key Press Markup Language (KPML) events by the addition of a SIP Trunk Group configurable flag 'KPML Subscribe Mode.'

KPML Subscribe Mode options:

• Consume – (Default) If chosen, the SBC consumes Subscribe messages and triggers KPML events for In-Dialog and OOD Subscribe messages.
• Relay – If chosen, the SBC relays KPML Subscribe messages for In-Dialog and OOD Subscribe messages.

For configuration details, refer to:

• SIP TG - Signaling - KPML Subscribe Mode - CLI
• SIP Trunk Group - Signaling (EMA)

Call Flows

One-Shot Subscription Call Flow

Persistent Request Call Flow

Outward Call Termination Call Flow

Outward Call Termination Call Flow

Inward Call Termination Call Flow

Inward Call Termination Call Flow

Subscription Expiration Call Flow

Subscription Expiration Call Flow

Reverse Stream Call Flow

When a KPML subscription is received with "stream=reverse" attribute, the SBC detects digits in the reverse direction with respect to the dialog details present in Event header of the SUBSCRIBE message.

Reverse Stream Call Flow

The SBC supports both the subscriptions (normal and reverse) to detect digits in both the directions of the call.