In this section:
The The video stream is allowed to pass-thru if the Packet Service Profiles used for both legs of the call allows video; i.e have a non-zero value for video bandwidth. This object is the H.323 Trunk Group for this zone. The SBC 7000 system supports creating IP Interface Groups containing sets of IP interfaces that are not "processor friendly" (i.e. carried on physical Ethernet ports served by separate processors). However, restrictions exist regarding the usage of such Interface Groups. (This ability does not apply to the SBC 5400, which has only two physical media ports. You may configure the IP interfaces from the two physical ports within the same IP Interface Groups without restrictions.) For complete details, refer to Configuring IP Interface Groups and Interfaces. On the SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning > Trunk Group > H323Trunk Group. The H323Trunk Group window is displayed. Trunk Group - H323Trunk Group The H323Trunk Group can be checked for each Address Context or for each Zone or for all the Address Contexts and Zones created. Use the drop-down box to select the desired Address Context and Zone. To edit any of the H323Trunk Group in the list, click the radio button next to the specific H323Trunk Group name. The Edit Selected H323Trunk Group window is displayed below. Trunk Group - H323Trunk Group Edit Window Make the required changes and click Save at the right hand bottom of the panel to save the changes made. To create a new H323Trunk Group, click New H323Trunk Group tab on the H323Trunk Group List panel. Trunk Group - H323Trunk Group Fields The Create New H323Trunk Group window is displayed. Trunk Group - H323Trunk Group Create Window The following fields are displayed: H323Trunk Group Parameters Parameter Description Name Specifies the name of the H323 Trunk Group. State The administrative state of the H 323 Trunk Group: Mode The operation mode of the H 323 trunk group Action The action for the operation mode for this H323 trunk group. Dry Up Timeout The time (in minutes) to wait for active calls to finish. Default is 5 minutes. Sending Complete Enbloc Specifies whether to send the complete IE in enbloc SETUP message. The options are: Parent shared Cac Limits Pool Name Specifies an existing shared CAC pool. Localization Variant Indicates the variant used by the Policy in call processing. Possible values: Digit Parameter handling Digital Parameter Handling parameters: Call Routing Call Routing parameter: Media Media parameter: Services Service parameters: Signaling Profiles: Flags: Minimum Duration Specifies the period of outage for a call, in milliseconds, for that call to be counted as part of the packet outage detection algorithm. Must be 0-65535, default is 6000 (milliseconds). Minimum Calls Specifies, for the current interval, the number of calls with outages that are required to declare a packet outage event. Must be 0-65535, default is 1000 (calls). Bandwidth Limit Reduction Specifies the amount to reduce the bandwidth limit (as a percentage of the configured limit) when a packet outage is detected. Must be 0-100, default is 50 (percent). Detection State Specifies the administrative state of packet outage detection: Detection Interval Specifies the time interval, in minutes, for detecting packet outages via the packet outage detection algorithm. Must be 5-1440, default is 15 (minutes). State Administrative state of the call reservation. Priority Call Minimum The number of priority call allowed when reservations are enabled for this trunk group. Enter value in range of 0-100. Default is 1. Incoming Call Minimum The number of incoming call allowed when reservations are enabled for this trunk group. Enter value in range of 0-128. Default is 1. Outgoing Call Minimum The percent of outgoing call allowed when reservations are enabled for this trunk group. Enter value in range of 0-100. Default is 10. SILC traffic control configuration. Specify the following SILC parameters: Call Limit The total number of concurrent calls (either ingress or egress) allowed. Enter unlimited or value in range of 0-2147483647. Bandwidth Limit Total media bandwidth limit (in K bits/sec). Enter unlimited or value in range of 0- 2147483647. Call Limit Threshold Specifies the call utilization notification threshold limit. The value range from 0 to 100. Bandwidth Limit Threshold Specifies the bandwidth utilization notification threshold limit. The value range from 0 to 1000. Specifies the value of maximum allowed burst in calls/second (above the allowed sustained rate) for ingress call attempts. The default value is Specifies the value of maximum allowed burst (above the allowed sustained rate) for ingress call attempts in calls/second. The default value is Default Qos Asr Specifies the default value to be used as ASR when no calls are made for a sampling period. The value range from 0 to 100. Critical Qos Asr Limit Specifies the critical ASR limit below which, the call admission should be stopped. The value range from 0 to 70. Major Qos Asr Limit Specifies the major ASR limit below which, the call admission should be reduced. The value range from 0 to 90. This parameter controls the number of called address digits to be collected before performing the 1st policy query during overlap receiving. If this is 0, then this parameter is irrelevant in controlling policy query. Ldc Rel Cause Specifies the Q.850 release value to use should the call be released due to long duration call timer expiry. Ldc Emergency Calls Specifies whether the Emergency Calls should be excluded from Long Duration Call Media IP Interface Group Name Specifies the Interface group to be used for media. Source Address Filtering If enabled, filter out incoming media packets which do not match the expected source IP address and UDP port. Direct Media Allowed If enabled, attempts to set up a direct-media path so that media flows directly between endpoints in the same direct-media group. If disabled, set up the path so that media transverses the SBC. Direct Media Group ID Specifies the direct media group to which this trunk group belongs. The value range from 0 to 65535. The default value is 0. Pre allocate Res Pad Specifies whether a resource pad is pre-allocated during an incoming fast start call procedure that results in G.711 codec selected for the call or not. The options are: Specifies whether an ingress H245 Slow Start should be converted to a forward offer at egress (e.g. Fast Start) or passed thru as a reverse offer (e.g. Slow Start). The options are: Ans Supervision Timeout This is the maximum time (in seconds) from egress call setup to egress receiving an answer. Crank Back Profile Specifies the name of the Crank Back profile. Respect Bearer Capability Specifies whether to accept unchanged the Bearer Capability Information element values received in H.225 SETUP or not. The options are: To copy any of the created H323Trunk Groups and to make any minor changes, click the radio button next to the specific H323Trunk Groups to highlight the row. Click Copy H323Trunk Group tab on the H323Trunk Groups List panel. Figure 5: Trunk Group - H323Trunk Group Fields The Copy Selected H323Trunk Group window is displayed along with the field details which can be edited. Figure 9: Trunk Group - H323Trunk Group Copy Window Make the required changes to the required fields and click Save to save the changes. The copied H323Trunk Group is displayed at the bottom of the original H323Trunk Group in the H323Trunk Group List panel. To delete any of the created H323Trunk Group, click the radio button next to the specific H323Trunk Group which you want to delete. Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision. Click Yes to remove the specific H323Trunk Group from the list.Unable to show "metadata-from": No such page "_space_variables" supports H.323-H.323 calls with an audio and video stream. Unlike SIP video where all codecs are relayed through the Unable to show "metadata-from": No such page "_space_variables", H323 only supports a subset of the video codecs supported via SIP. The codecs are:Payload Type Codec Variants 31/Dynamic H.261 34/Dynamic H.263 Dynamic H.263-1998 Dynamic H.263-2000 Dynamic H.264 Dynamic H.264-RCDO Dynamic H.264-SVC
Note
To View H323Trunk Group
To Edit H323Trunk Group
To Create H323Trunk Group
Policy Carrier The four-digit carrier code. Country Specifies the Country Code to be used for this policy. Click Select to choose the country code you want to choose. —A unique identifier for the numbering plan.—The name of the ingress DM/PM (digit manipulation/ parameter manipulation) rule, up to 23 characters.—The name of the egress DM/PM rule.—The Element Routing Priority table indicates what originating Call Processing Elements types (including "none") should be used to determine matching routing table entries. —The packet service profile entry used to identify a particular packet service profile.—Specifies the name of the Tone and Announcement Profile used.—Specifies the class of service to be usedSignaling —The name of this IP signaling profile.Ingress Packet Outage —packet outages are not detected and the maximum bandwidth limit is restoredCall Reservation Parameters for reserving a portion of the resources for specific call direction or type for this H323 trunk group. Specify the following call reservation parameters. Inbound Percentage of call Limit reserved for handling inbound calls. This is the percentage of channels reserved for handling inbound calls. Default is 0%. Percentage selection allowed in 5% increments. Enter value in 5% increments in range of (0-100) percent. SILC CAC Ingress Call Rate Max unlimited (range: 1-450, or unlimited. SBC 7000 range is 1-1350, or unlimited).Call Burst Max unlimited (range: 1-900, or unlimited. SBC 7000 range is 1-2700, or unlimited).Egress Call Limit Specifies the total number of calls allowed for Egress Call Rate Max Specifies the value of maximum allowed burst in calls/second (above the allowed sustained rate) for egress call attempts. The default value is unlimited (range: 1-450, or unlimited. SBC 7000 range is 1-1350, or unlimited).Call Burst Max Specifies the value of maximum allowed burst (above the allowed sustained rate) for egress call attempts in calls/second. The default value is unlimited (range: 1-900, or unlimited. SBC 7000 range is 1-2700, or unlimited).Qoe Min Time To Proceed Specifies the minimum time period before the call admission can start after any of the TG's KPI fall below the critical threshold. The value range from 0 to 3600 Rfactor Critical Qos Rfactor Limit Specifies the critical R-Factor limit, below which the call admission should be stopped if it is an incoming TG and also marked OOS. If this does not return a policy response in a routing label, this field will not be chosen for routing. The value range from 0 to 100. Major Qos Rfactor Limit Specifies the major R-Factor limit, below which the call admission should be reduced. This is just an info level log. \The value range from 0 to 100. Asr Scru Critical Qos Scru Limit Specifies the critical Sustained Call Rate Utilization(SCRU) limit below which, the call admission should be stopped. The value range from 80 to 100. Clu Critical Qos Clu Limit Specifies the critical Call Limit Utilization(CLU) below which, the call admission should be stopped. The value range from 80 to 100. pgrd Critical Qos Pgrd Limit Specifies the critical Post Gateway Ringing Delay limit above which, the call admission should be stopped. The value range from 50 to 10000. Default Pgrd Factor Specifies the default value to be used as the Post Gateway Ringing delay when no calls are made for a sampling period. The value range from 50 to 10000. Services Overlap Dialing Overlap State Determines if the overlap is supported or not. Select one of the option: enable/ disable. Min Digits for Query Long Duration Call Ldc Timeout Specifies the timeout value of the long duration call timer in minutes. Ldc Action Specifies the action to take if the long duration call timer.
Disconnect procedures or not. The options are:Media Slow Start Call Routing To Copy H323Trunk Group
To Delete H323Trunk Group
Overview
Content Tools