In this section:

This object specifies the gateway to which you wish to direct traffic from your Packet, Management, or Link Interface. In effect, this object allows you to add, change, and delete gateways (next Hops) to these interfaces. Interface and static routes combine to form the IP routing table for your network.

This table must ultimately provide a route to each potential call destination IP address. The static route is used to add static IP routes for the IP interfaces. A static route indicates the nextHop gateway and IP interface that should be used for a particular peer network IP prefix.



Note

Each signaling port within an Address Context must use a unique IP address and port number combination.


Note

The  SBC 7000 system supports creating IP Interface Groups containing sets of IP interfaces that are not "processor friendly" (i.e. carried on physical Ethernet ports served by separate processors). However, restrictions exist regarding the usage of such Interface Groups.

(This ability does not apply to the SBC 5400, which has only two physical media ports. You may configure the IP interfaces from the two physical ports within the same IP Interface Groups without restrictions.)

For complete details, refer to Configuring IP Interface Groups and Interfaces.

To View Static Route

On SBC main screen, navigate to Configuration > System Provisioning > Category: Base Provisioning > Static Route.

The Static Route window is displayed.

Figure 1: System Provisioning - Static Route

The Static Route can be checked for each Address Context or for all the Address Contexts created. Use the drop-down box to select the desired Address Context.

To Edit Static Route

To edit any of the Static Routes in the list, click the radio button next to the specific Static Route name.

The Edit Selected Static Route window is displayed below.

Figure 2: Static Route Edit Window

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

The SBC does not allow to edit the Condition for a Static Route. To change the configuration of Condition, delete the Static Route and reconfigure it.

To Create Static Route

To create a new Static Route, click New Static Route tab on the Static Route List panel. The Create New Static Route window is displayed.

Figure 3: Static Route Create Window


The following fields are displayed:

Table 1: Static Route Parameters


Parameter


Description

Destination IP Address

The destination IP address. The following IP address types are supported:
• IPv4—This is V4 IP address in dotted decimal form (for example 128.127.50.224).
• IPv6—This is V6 IP address in hexadecimal/colon form (for example,
1280:1276:3350:2224:2222:3333:8888:1245 or fd00:21:445:128::7880). Default is
0:0:0:0:0:0:0:0.

Prefix

The IP prefix of this static route entry.

Next Hop

The address of the next system en-route to the destination.

IP Interface
Group Name

The name of an IP interface group.

IP Interface
Name

The name of the IP interface for this entry.

Preference

Route preference value.

Condition

An element in the Static Route configuration that holds the conditions on the basis of which routes are added to a SBC pair with HA configuration.

Currently, Condition supports only one child element - CE Name.

NOTE: The Condition option is only applicable to non-management interfaces.

CE NameThe name (1 - 255 characters) of the computing element that hosts the port used by the IP interface.

For a High Availability (HA) pair configuration, the SBC allows configuring a Static Route for a specific host or CE Name among the active and standby hosts of a HA pair configuration using the Condition element. The Condition element store the conditions on the basis of which routes are added to a SBC pair with HA configuration. Currently, the Condition element only supports the CE Name element.

Before configuring the Condition using a specific CE Name, ensure that IP Interface Group Name and IP Interface Name are configured. These three elements cannot be configured and saved simultaneously. For further details, refer to System Provisioning - IP Interface Group and IP Interface Group - IP Interface.

Static Routes with specific CE Name can be added only for packet interfaces.

To Copy Static Route

To copy any of the created Static Route and to make any minor changes, click the radio button next to the specific Static Route to highlight the row.

Click Copy Static Route tab on the Static Route List panel. The Copy Selected Static Route window is displayed along with the field details which can be edited.

Figure 4: Static Route Copy Window


Make the required changes to the required fields and click Save to save the changes. The copied Static Route is displayed at the bottom of the original Static Route in the Static Route List panel.

To Delete Static Route

To delete any of the created Static Route, click the radio button next to the specific Static Route which you want to delete.

Click the Delete symbol at the end of the highlighted row. A delete confirmation message appears seeking your decision.

Click Yes to remove the specific Static Route from the list.

  • The SBC does not allow to delete the CE Name separately.
  • Static Route is deleted only from the instance in which it is configured, and not from both active and standby instances of a HA pair SBC configuration.
  • No labels