The SBC 5100, SBC 5110, SBC 5200, and SBC 5210 platforms are no longer supported beginning with the SBC Core 10.0.0R0 release. This release supports SBC 5400/7000/SWe platforms. Contact Ribbon Sales for upgrade information.
Identify and download the correct firmware file for your platform type. The upgrade fails if the selected firmware upgrade file does not match the platform type. The following table identifies the correct firmware files for an upgrade:
Platform Type | Firmware file |
---|---|
SBC 5000 Series (5110/5210) | Upgrade from 2.x to 3.x version:
Upgrade from 3.x to 3.y version:
|
SBC 5400 | Upgrade from any version to latest version:
|
SBC 7000 (Refer to Upgrading the BMC and BIOS Firmware for the procedure.) | Upgrade from any version to latest version:
|
There are two BMC firmware upgrade procedures based on the version from which you are upgrading. Each method requires a different file type as listed in the previous table. The SBC 5000 series supports both paths. The SBC 5400 supports only the upgrade method using the ".img
" file.
BMC upgrade from 2.x to 3.x: Use the ".rom
" file.
For example: To upgrade from BMC 02.16.00 to 03.17.00, use "bmc5X00_v3.17.0-R0.rom
" file.
The firmware upgrade to 3.x can only be done from version 02.16.00 or later. If the existing BMC version is older than 02.16.00, upgrade it to 02.16.00 using the ".rom
" file first and then perform an upgrade to 3.x version using a ".rom
" file.
.img
" file. For example: To upgrade from BMC 03.00.00 to 03.17.00, use "firmware-5XX0-V03.17.00-R000.img
" file.
Download the required BMC firmware version prior to continuing. Refer to Downloading Software from the Ribbon Support Portal for details.
Windows and/or dialog boxes depicted in this section are intended as examples only and may not reflect the actual software/firmware versions applicable to you. Refer to any associated hardware/software requirements as well as the relevant release note for software/firmware version details.
The following procedure describes how to upgrade the BMC firmware from 2.x version using the ".rom
" file.
Log on to the SBC BMC GUI.
BMC 2.16 Login Screen
The BMC Main screen is displayed.
BMC 2.16 Main Screen
Click Remote Control. The Remote Control window is displayed.
BMC 2.16 Remote Control Screen
Click Power Control in the Options panel. The Power Control and Status window is displayed.
BMC 2.16 Power Control Screen
Choose Power Off Server - Orderly Shutdown option.
The BMC server must be shut down prior to performing a firmware upgrade.
BMC 2.16 BMC Orderly Shutdown
Click Perform Action to initiate the shutdown process.
BMC 2.16 BMC Shutdown
Click the Maintenance tab. The Maintenance window is displayed.
BMC 2.16 Maintenance Window
Click Enter Update Mode. Confirm that you want to enter update mode when prompted.
BMC 2.16 Maintenance Window Confirmation Message
Click OK to proceed. The BMC is now in Upgrade Mode.
BMC 2.16 Firmware Update window
Browse and select the firmware file to upload. The firmware file to upgrade from 2.x version should be a .rom
file. For example: bmc5X00_v3.17.0-R0.rom
file.
Click Upload Firmware. The BMC validates the selected file.
The BMC fails to upgrade if:
Once the verification is complete, a message is displayed stating the result of the verification.
BMC 2.16 Firmware Validation
Click OK to proceed. The existing and the new BMC versions are displayed for validation.
BMC 2.16 Firmware Comparison
Click Start Upgrade to initiate the upgrade process. Confirm that you want to upgrade when prompted.
BMC 2.16 Upgrade Confirmation message
Once the upgrade process starts, do not close the screen.
Click OK to proceed. The BMC starts the firmware upgrade process.
BMC 2.16 Upgrade Process
Once the upgrade process is complete, the BMC reboots and a message appears requesting you to open a new browser window to access the BMC GUI.
BMC 2.16 Upgrade Process Complete
Access the same BMC IP address to reach the BMC login window. In the new BMC version (3.X), the login window includes additional browser settings.
BMC 3.X Login Window
Log on to the SBC BMC GUI.
The following procedure describes how to upgrade the BMC firmware from a 3.x version to a 3.y version (for example, from version 03.10.00 to version 03.17.00) or from 1.x to a 3.x version using the ".img
" file.
Log on to the SBC BMC GUI.
BMC Login Screen
The BMC main screen is displayed.
SBC BMC Main Screen
Click Firmware Update.
BMC Firmware Update option
The Firmware Update screen is displayed.
BMC Firware Update screen
Click Browse, and from the Open dialog browse to and select the firmware image (for example; firmware-5XX0-V03.17.00-R000.img). Refer to the table at the start of this page to make sure you have chosen the correct type of file for an upgrade. To determine the exact firmware version, refer to the release notes in SBC Release Information.
Click Upload.
The firmware image is approximately 17MB for the SBC 5000 Series and 24MB for the SBC 5400 and takes few minutes to upload based on the network.
The BMC fails to upgrade if:
The selected file is verified and the uploading process starts.
Once the file verification is complete, when prompted, click Confirm to proceed with the upgrade.
This is a service-affecting procedure and will power off the host side of the SBC.
After you confirm, the BMC initiates an orderly shutdown of the host. If the process to shutdown the host fails, the upgrade fails. Take one of the following actions based on the current BMC version:
Once the upgrade process starts, do not close the screen.
Once the update process is complete, a completion message displays.
Firmware Update Complete message
Click OK to complete the process.The BMC automatically restarts at this point.
Close the existing browser window.
Clear the browser cache and log on to the BMC GUI again. The updated BMC version is displayed on the BMC main screen.
Log onto the BMC GUI.
The SBC BMC prompts you to change the password after a successful upgrade only if it is a default password.
Change Default Password Window
Click OK to proceed. The User Management window is displayed.