You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 12 Next »

In this section:

The ConnexIP Operating System jump start installation is required in cases such as, reverting to older releases, SSD drive replacement. To re-install ConnexIP OS, follow the procedure below:

Note

The ConnexIP ISO installation procedure automatically copies the SBC application package to the SBC platforms. 

Note

The ConnexIP ISO installation procedure takes around 30 to 40 minutes to complete.

Downloading ConnexIP ISO Image

Download the following ConnexIP OS files bundled from the Sonus Salesforce customer portal:

  • sbc-V06.02.00R000-connexip-os_05.00.00-R000_amd64.iso
  • sbc-V06.02.00R000-connexip-os_05.00.00-R000_amd64.iso.md5

Refer to Downloading the Software from Salesforce to know more.

To determine the exact OS versions, refer the appropriate release notes at SBC Release Information.

Installing OS

 

Reinstalling the OS will format your disk and erase all data. Sonus highly recommends saving the configuration data to a remote server before reinstalling the OS in the event you need to restore the original configuration data after the re-installation.

The following procedure describes how to reinstall the ConnexIP OS:

  1. Launch the host remote console through the BMC. Refer to Launching the Remote Console from the BMC.

  2. Select Media in the JViewer and click Virtual Media Wizard.

    Virtual Media Wizard

  3. The Virtual Media screen appears. Select ISO Image from CD/DVD Media1 section of the screen.

    Virtual Media Screen

  4. Click Browse. From the Open dialog, browse to and select the connexip-os_<version>_amd64.iso file and click Open.

    Open Dialog Screen

  5. Click Connect CD/DVD. A message Device redirected in Read Only Mode appears on the screen. Click OK to continue. This mounts the ISO image from your local desktop or laptop.

    Mounting Virtual CD/DVD

  6. Click Close to exit the window.
  7. Minimize the JViewer window.

  8. On the SBC BMC GUI, navigate to Remote Control > Server Power Control. The Power Control and Status window is displayed.
    Observe that the "Host is currently on" message in the window.

    Server Power Control Window

  9. Select Power Off Server-Orderly Shutdown option and click Perform Action. This action brings the SBC host down.

    Server Power Control - Off Option

  10. Once the SBC host is down, from the same location, select Power On Server and click Perform Action. This action powers on and reboots the SBC host. 

    Server Power Control - On


    Once the BMC is up and running, access the JViewer window.

  11. Press <DEL> or <F2> immediately, when the splash screen appears.

    BIOS Splash Screen

    The BIOS setup utility screen is displayed.

  12. Use right arrow key to navigate to the Save & Exit menu.

    BIOS Setup Utility

  13. Select AMI Virtual CDROM0 1.00 from Save & Exit menu to boot from the virtual CD drive. This instructs the server to boot from the redirected ConnexIP OS ISO image.

    Booting from Virtual CD Drive

  14. Select Install and press <Enter> to start the installation.

    Sonus ConnexIP Installer Boot Menu

  15. The automated installation process starts. This process takes approximately 30 to 40 minutes.

    Partitions Formatting Screen

    Installing the Base System

    Selecting and Installing Software

    Copying SBC Package

    Running Post Install


    Once the installation is complete, the disk partition upgrade starts. At this stage, DO NOT power off the system.

    Disk Partitioning


    Once the system reboots, the ConnexIP login screen appears on the screen.

    ConnexIP Login Screen

    This concludes the ConnexIP OS Installation/Re-installation process.

  16. Close the JViewer window.

Continue to install the desired SBC Application build. Refer to Installing SBC Application to know more.

 

  • No labels