You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 2 Next »

The Credentials and Registration window configures authentication credentials and specifications for registering Address of Records (AORs).  

  1. Choose VoIP > SIP > B2BUA.

  2. Scroll to the Credentials and Registration window. If necessary, click New Entry to open the new credentials and registrar entry window.

  3. Configure settings using the information in the following table as a guide. When you have finished configuring settings, click Update to make your changes take effect.

    B2BUA Credentials and Registration Configuration Parameters

    ItemDescription

    Credentials and Registration

    Displays a list of registered AORs. Refer to Manage B2BUA Credentials and Registration.

    AOR

    Displays the Address of Record or Username. The values in this column can be one of the following:

    • Username—If the entry is an Authentication credential or the registrar is the default proxy, this column displays the Username, for example, 2408881028.

    • SIP URI—If the entry is for registering an AOR to the non-default proxy, full SIP URI is displayed. For example, sip:1234567890@sipdomain.com. Where “sipdomain.com” is the domain name of the registrar.

    • Default—For default or wild card credentials.

    Auth-User

    Displays the authentication user. If the field is blank, the authentication user is the same as the Username.

    The AOR Auth-User field supports up to 50 characters. A warning message is displayed on the B2BUA Trunking Configuration page if more than 50 characters are entered.

    Password

    Specifies the shared secret for SIP digest authentication.

    Registrar

    Displays registrar information:

    • If an address was given for a non-default registrar, this is shown in the format IP-ADDRESS:PORT.

    • If no address was given for a non-default registrar, this field is blank because the address is determined through a DNS A lookup.

    • The field displays “Default” for the default SIP Registrar.

    Status

    Displays registration status:

    • Trying—The register request has been sent but no response has been received yet.

    • OK—A 200 response was received. The registration is successful.

    • Error message—The error code and the error phrase are displayed. For example, the registration failed for 403 Forbidden.

    Transport

    Displays the transport protocol used for Registration. If the default SIP server is configured as the registrar, then the SIP server Transport is shown as the transport protocol. When the SIP server Transport is 'Pass Through', UDP is chosen as the transport protocol.

    Credentials - New Entry

    Creates new credentials and registration information.

    Username

    Enter a valid SIP Username. This becomes part of the user portion of the AOR. If you want to enter a default credential, leave this field blank.

    Auth-User

    Enter the required default credentials. Otherwise, leave this field blank; B2BUA uses the Username as Auth-user.

    Edit Password

    		Select the Edit Password checkbox to edit the password.
    Password

    Enter the required shared secret for SIP digest authentication. This field cannot be blank if you entered credentials in the Auth-User field.

    Confirm Password

    Re-enter the required shared secret for SIP digest authentication.

    Use as defaultSelect the Use as Default checkbox to use this SIP Authentication credential by default (recommended).

    Registrar - New Entry

    Select a registration type radio button:

    • Don't Register—Default. The Username will not be registered.
    • Use B2BUA Rule—Configures the HMR rules for the REGISTER pilot message headers.
    • Default SIP Proxy—B2BUA uses the default SIP proxy as configured on the SIP Settings page. Choose VoIP > SIP and refer to Configure SIP Protocol Settings to register the AOR.
    • Custom URI Domain—This configured custom domain is used in pilot registrations. It is applicable when IMS proxy mode is enabled in the survivability page.
    • Custom—Specifies custom Registrar settings.
    Domain

    Enter the Registrar domain. This should be entered as sip:proxydomain.com or sip:1.2.3.4.

    Address

    (Optional) Enter the Registrar's IP Address.

    If the IP address is provided, B2BUA does not do a DNS A lookup on the domain name and uses this address instead.

    PortEnter the Registrar port.
    Transport

    Select the Registrar port from the Transport drop-down list:

    • UDP

    • TCP

    • TLS

    Register Options (Optional)

    (Optional) Sets registration options when you set Default SIP Proxy or Domain as the Registrar:

    • Default Expires—Enter the number of seconds until expiration for the initial Register request. The field defaults to 3600 seconds if left blank.

    • Renew Interval—Enter the percentage of registration interval after which the B2BUA will renew the registration. The field defaults to 80% if left blank.

  4. To edit a credentials entry:

    1. Click once on the entry in the Credentials and Registration table. The row is highlighted, and the information about the selected line is displayed in the details box below the table.

    2. Edit details and click Update. Your changes are applied to the local cache. To save your configuration changes to the

      Unable to show "metadata-from": No such page "_space_variables"
      , click Submit.

  5. To delete a credentials entry, click the red X next to the selected entry. The entry is immediately removed from the Credentials and Registration table. You do not have to click Submit when deleting an entry.

  6. Click Update to save your settings in the Credentials and Registration window.

  7. Proceed to Manage B2BUA Actions.

  • No labels