In this section:
This page describes CLI syntax and parameters for the SIP Trunk Group 'Call Admission Control' object.
Note
As a best practice, always use UPPERCASE for trunk group names.
Note
Unless annotated otherwise, the parameter values in this section apply to the SBC Core.
Note
SIP subscription CAC limits are not applied to SUBSCRIBE requests from registered users in access deployments.
SIP Trunk Group CAC
Command Syntax
% set addressContext <name> zone <name> sipTrunkGroup <name> cac
bandwidthLimit <0-2147483647>
bandwidthLimitThreshold <0-100>
bandwidthVideoThreshold <0-100>
callLimit <0-2147483647>
callLimitThreshold <0-100>
egress
emergencyOversubscription <0-1000>
estimatedChildRegistrations <1-256>
extendedEmergencyIpLimit <0-40000>
hpcOversubscription <0-100>
ingress
registeredEndpointCacProfile <profile name>
registrationLimit <0-2147483647>
subscriptionLimit <0-2147483647>
tcpMediaLimit <0-5000>
unRegisteredEndpointCacProfile <profile name>
Command Parameters
SIP Trunk Group CAC Parameters
| Parameter | Length/Range | Description |
|---|---|---|
bandwidthLimit | 0-2147483647, or unlimited | The total media bandwidth limit, in Kbits/sec. (default = "unlimited") |
bandwidthLimitThreshold | 0-100 | Enter threshold value (as a percentage) to specify bandwidth utilization notification threshold. (range: 0-100 / default = 0) |
bandwidthVideoThreshold | 0-100 | Enter threshold value (as a percentage of video bandwidth) to limit video streams to a specific bandwidth to prevent video calls consuming call bandwidth otherwise needed for audio calls. (range: 0-100 / default = 0) |
callLimit | 0-2147483647, or unlimited | Total number of concurrent calls (either ingress or egress) allowed. (default = “unlimited”). |
callLimitThreshold | 0-100 | Call Limit utilization notification threshold, as a percentage. (default = 0) |
egress | N/A | Egress-specific call admission control configuration for the SIP trunk group. See Egress Parameters table below for details. |
emergencyOversubscription | 0-1000 | The percentage of resource oversubscription allowed for emergency calls. (default = 10) |
estimatedChildRegistrations | 1-256 | Estimated number of child registrations (i.e. the estimated number of P-Associated-URIs in 200 OK message). (default = 1) |
extendedEmergencyIpLimit | 0-40000 | The resource oversubscription (expressed as numeric value) allowed for emergency calls. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
ingress | N/A | Ingress-specific call admission control configuration for the SIP trunk group. See Ingress Parameters table below for details. |
registeredEndpointCacProfile | N/A | <SIP CAC Profile Name> – The name of the SIP CAC Profile (containing endpoint CAC parameters that are applied individually to each registered peer) to associate with this trunk group. |
registrationLimit | 0-2147483647, or unlimited | The total number of concurrent SIP registrations allowed. (default is 'unlimited') |
subscriptionLimit | 0-2147483647, or unlimited | The total number of concurrent SIP subscriptions allowed on IP trunk group. (default is 'unlimited') |
tcpMediaLimit | 0-5000, or unlimited | MRM session limit per trunk group. |
| N/A |
(Refer to SIP CAC Profile - CLI for profile details.) |
Egress
Command Syntax
% set addressContext <name> zone <name> sipTrunkGroup <name> cac egress callBurstMax <1-900> (SBC 7000 range is 1-2700) callLimit <0-2147483647> callRateMax <1-450> (SBC 7000 range is 1-1350) emergencyOversubscription <0-1000> extendedEmergencyIpLimit <0-40000> hpcOversubscription <0-100> otherReqBurstMax <1-1000> (SBC 7000 range is 1-3000) otherReqRateMax <1-1000> (SBC 7000 range is 1-3000) registerBurstMax <1-1000> (SBC 7000 range is 1-3000) registerRateMax <1-1000> (SBC 7000 range is 1-3000) subscribeBurstMax <1-1000> (SBC 7000 range is 1-3000) subscribeRateMax <1-1000> (SBC 7000 range is 1-3000)
Command Parameters
Cal policing using callRateMax and callBurstMax is applicable only to normal and emergency calls, not to high priority calls (HPC).
Egress Parameters
| Parameter | Length/Range | Description |
|---|---|---|
callBurstMax | SBC 5000: 1-900, or unlimited SBC 7000: 1-2700, or unlimited | Maximum allowed burst size (above the allowed sustained rate) for egress call attempts, in calls per second. (default = 'unlimited') |
callLimit | 0-2147483647, or unlimited | Total number of concurrent calls (either ingress or egress) allowed on egress. (default = 'unlimited') |
callRateMax | SBC 5000: 1-450, or unlimited SBC 7000: 1-1350, or unlimited). | Maximum sustained egress call rate allowed in calls per second. (default = 'unlimited') NOTE: You can set both |
emergencyOversubscription | 0-1000 | Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10) |
extendedEmergencyIpLimit | 0-40000 | The resource oversubscription (expressed as numeric value) allowed for emergency calls. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are stopped, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
otherReqBurstMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum allowed burst (above the allowed sustained rate) for any other egress out-of-dialog SIP request. (default = 'unlimited') |
otherReqRateMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum sustained egress rate (requests per second) of other out-of-dialog SIP requests. (default = 'unlimited') |
registerBurstMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum allowed burst (above the allowed sustained rate) for egress initial SIP registrations. (default = 'unlimited') |
registerRateMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited) | Maximum sustained egress rate (registrations per second) of initial SIP registrations allowed. (default = 'unlimited') NOTE: You can set both |
subscribeBurstMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum allowed burst (above the allowed sustained rate) for egress initial SIP subscribe request. (default = 'unlimited') |
subscribeRateMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum sustained egress rate (subscribes per second) of initial SIP subscribe request. (default = 'unlimited') |
Ingress
Command Syntax
% set addressContext <name> zone <name> sipTrunkGroup <name> cac ingress callBurstMax <1-900> (SBC 7000 range is 1-2700) callLimit <0-2147483647> callRateMax <1-450> (SBC 7000 range is 1-1350) emergencyOversubscription <0-1000> hpcOversubscription <0-100> extendedEmergencyIpLimit <0-40000> otherReqBurstMax <1-1000> (SBC 7000 range is 1-3000) otherReqRateMax <1-1000> (SBC 7000 range is 1-3000) registerBurstMax <1-1000> (SBC 7000 range is 1-3000) registerRateMax <1-1000> (SBC 7000 range is 1-3000) subscribeBurstMax <1-1000> (SBC 7000 range is 1-3000) subscribeRateMax <1-1000> (SBC 7000 range is 1-3000)
Command Parameters
Cal policing using callRateMax and callBurstMax is applicable only to normal and emergency calls, not to high priority calls (HPC).
Ingress Parameters
| Parameter | Length/Range | Description |
|---|---|---|
callBurstMax | SBC 5000: 1-900, or unlimited SBC 7000: 1-2700, or unlimited | Maximum allowed burst (above the allowed sustained rate) for ingress calls in calls per second. (default = 'unlimited') |
callLimit | 0-2147483647, or unlimited | Total number of concurrent calls allowed on ingress. (default = 'unlimited') |
callRateMax | SBC 5000: 1-450, or unlimited SBC 7000: 1-1350, or unlimited | Maximum sustained ingress call rate allowed in calls/second. (default = 'unlimited') NOTE: You can set both |
emergencyOversubscription | 0-1000 | The amount of resource over-subscription (as a percentage) allowed for emergency calls. (default = 10) |
extendedEmergencyIpLimit | 0-40000 | The resource oversubscription (expressed as numeric value) allowed for emergency calls. (default = 0) |
hpcOversubscription | 0-100 | This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10) |
otherReqBurstMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum allowed burst (above the allowed sustained rate) for any other ingress out-of-dialog SIP request. (default = 'unlimited') |
otherReqRateMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum sustained ingress rate (requests per second) of other out-of-dialog SIP requests. (default = 'unlimited') |
registerBurstMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum allowed burst (above the allowed sustained rate) for initial SIP registrations. (default = 'unlimited') |
registerRateMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum sustained rate of initial SIP registrations allowed in registrations per second. (default = 'unlimited') NOTE: You can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. |
subscribeBurstMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum allowed burst (above the allowed sustained rate) for ingress initial SIP subscribe request. (default = 'unlimited') |
subscribeRateMax | SBC 5000: 1-1000, or unlimited SBC 7000: 1-3000, or unlimited | Maximum sustained ingress rate (subscribes per second) of initial SIP subscribe request. (default = 'unlimited') |
Overview
Content Tools