You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 2 Next »

Back to Table of Contents

Back to CLI Configure Mode

Back to System - CLI

Additional section:

In this section:

This object specifies a Network Time Protocol (NTP) server that supplies local time to the 

Unable to show "metadata-from": No such page "_space_variables"
. The reference time delivered by NTP is the source of all time stamps placed into the accounting records.

During the installation process, the NTP server and time zone information is input to the Active server only. Once the Standby server starts, this information is synced from the Active to Standby.

The 
Unable to show "metadata-from": No such page "_space_variables"
should receive an initial time synchronization from NTP server before accepting calls.

Command Syntax

The following CLI syntax is used to configure NTP server at system level.

% set system ntp
	keys <key Id>
		keyType <MD5 | SHA1>
		keyValue <key value>
	serverAdmin <IP_address>
		authKey <key Id>
		maxPoll <10-17>
		minPoll <4-17>
		state <disabled | enabled>
		version <version3 | version4>
	timeZone <SYSTEM NAME>
		zone <zone>

Changing the time zone forces a restart of the 

Unable to show "metadata-from": No such page "_space_variables"
application, and thus cause a service outage for a few minutes. 
Unable to show "metadata-from": No such page "_space_variables"
recommends changing the time zone only during a system maintenance window. See Changing the Time Zone for details.

Command Parameters

NTP Services Management parameters

Parameter

Length/Range

Description

keys

 N/A

<key Id> – NTP authentication key Identifier to obtain from NTP server, with following attributes:

  • keyType – NTP authentication key type to assign to the SBC for this <keyId>:
    • MD5 – MD-5 (Message Digest Algorithm) cryptographic hash function.
    • SHA1 – SHA-1 (Secure Hash Algorithm) cryptographic hash function.
  • keyValue <key value> – NTP authentication key value to assign to the SBC for this <keyId>.

serverAdmin

N/A

<ip_address> – The NTP server IP address.

  • authKey <key Id> – NTP authentication key to authenticate the server (Use NTP server <keyId> configured in keys command).
  • maxPoll – The maximum poll interval, in seconds to the power of 2, for this NTP Server. The maxPoll parameter value range is 10 - 17 (1,024 seconds to 36.4 hours). (range: 10-17 / default = 10).
  • minPoll – The minimum poll interval, in seconds to the power of 2, for this NTP Server. The minPoll parameter value range is 4 - 17 (16 seconds to 36.4 hours). (range: 4-17 / default = 4).
  • state– NTP server state.
    • disabled – (default) The state of the NTP server is disabled.
    • enabled – The state of the NTP server is enabled.
  • version– NTP server version.
    • version3 (default)
    • version4

timeZone

N/A

Time zone configuration.
 

  • <system_name> – 
    Unable to show "metadata-from": No such page "_space_variables"
    system name.
  • zone – Specify the time zone where the node resides. See Time Zones page.

Command Example

The following example enables NTP server version 4 at IP address 10.20.30.40, and sets time zone of the 

Unable to show "metadata-from": No such page "_space_variables"
system to U.S. Hawaii time.

% set system ntp serverAdmin 10.20.30.40 version version4  
% set system ntp serverAdmin 10.20.30.40 state enabled
% set system ntp serverAdmin 10.1.1.1 authKey 6 
% set system ntp timeZone SBC01 zone us-Samoa
% show system ntp
timeZone SBC01 {
    zone us-Samoa;
}
serverAdmin 10.160.20.53 {
    version version4;
    minPoll 4;
    maxPoll 10;
    state   enabled;
    authKey 6;
}
  • No labels