You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 2 Next »

In this section:

The

Unable to show "metadata-from": No such page "_space_variables"
supports Rx interface which pertains to QoS resource reservation for reserving bandwidth in the IP access network. The Rx reference point is used to exchange application level session information between the Policy and Charging Rules Function (PCRF) and the P-CSCF. The Access Solution, acting as P-CSCF creates a TCP connection with the configured PCRF.

Do not configure PCRF on the Egress leg of the Trunk Group for REGISTER.

 

Note

The SBC 52x0 and SBC 7000 systems support creating IP Interface Groups containing sets of IP interfaces that are not "processor friendly" (i.e. carried on physical Ethernet ports served by separate processors). However, restrictions exist regarding the usage of such Interface Groups.

(This ability does not apply to the SBC 51x0 and SBC 5400 systems which have only two physical media ports. IP interfaces from the two physical ports may be configured within the same IP Interface Groups without restriction.)

For complete details, refer to Configuring IP Interface Groups and Interfaces.

Only one instance of Diam Node can be created.

When configuring a Diameter Node in an HA configuration, the "Secondary Origin Host" parameter must be configured with the Standby hostname

To View Diam Node

On SBC main screen, navigate to All > Address Context > Diam Node.

The Diam Node can be checked for each Address Context or for all the Address Contexts created. Use the drop-down box to select the desired Address Context.

All - Address Context - Diam Node Main Field

The Diam Node window is displayed.

All - Address Context - Diam Node

To Edit Diam Node

To edit any of the Diam Node in the list, click the radio button next to the specific Diam Node name.

All - Address Context - Diam Node Highlighted

The Edit Selected Diam Node window is displayed below.

All - Address Context - Diam Node Edit Window

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

To Create Diam Node

To create a new Diam Node, click New Diam Node tab on the Diam Node List panel.

All - Address Context - Diam Node Fields

The Create New Diam Node window is displayed.

All - Address Context - Diam Node Create Window

The following fields are displayed:

Diam Node Parameters


Parameter


Description

Name

Specifies the name of this Diameter Node. The value ranges up to 23 characters.

Origin Realm

Specifies the description of the origin realm of this node. The value ranges up to 128 characters.

Primary Origin 
Host

Specifies the description of the primary origin of this node. The value ranges up to 128 characters.

Secondary 
Origin Host

Specifies the description of the secondary origin of this node. The value ranges up to 128 characters.

Transaction 
Timeout

Specifies the time out value in milli seconds. The value ranges from 500 to 6000 and the default value is 1000.

State

Specifies the state of the Diameter Node. The options are:

  • enabled
  • disabled (default)
Dump Pdu

When enabled, SBC logs the DIAMETER PDU sent and received on the Rx interface to the debug log. The options are:

  • enabled
  • disabled (default)
IP Interface 
Group Name

Specifies the name of the IP Interface group used by this node.

IP V4Address

Specifies the IPv4 address used to create connections towards peer.

IP V6Address

Specifies the IPv6 address used to create connections towards peer.

To Delete Diam Node

To delete any of the created Diam Node, click the radio button next to the specific Diam Node which you want to delete.

All - Address Context - Diam Node Highlighted

 

Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.

All - Address Context - Diam Node Delete Confirmation

Click OK to remove the specific Diam Node from the list.

 

  • No labels