Additional sections:
In this section:
This object is used to configure Gateway Trunk Group parameters.
Note
The SBC 52x0 and SBC 7000 systems support creating IP Interface Groups containing sets of IP interfaces that are not "processor friendly" (i.e. carried on physical Ethernet ports served by separate processors). However, restrictions exist regarding the usage of such Interface Groups.
(This ability does not apply to the SBC 51x0 and SBC 5400 systems which have only two physical media ports. IP interfaces from the two physical ports may be configured within the same IP Interface Groups without restriction.)
For complete details, refer to Configuring IP Interface Groups and Interfaces.
To View Gw Trunk Group
On SBC main screen, navigate to All > Address Context > Zone > Gw Trunk Group. The Gw Trunk Group can be checked for each Address Context and Zone or for all the Address Contexts and Zones created. Use the drop-down box to select the desired Address Context and Zone.
All - Address Context - Zone - Gw Trunk Group Main Field
The Gw Trunk Group window is displayed
All - Address Context - Zone - Gw Trunk Group
To Edit Gw Trunk Group
To edit any of the Gw Trunk Group in the list, click the radio button next to the specific Gw Trunk Group name.
All - Address Context - Zone - Gw Trunk Group Highlighted
The Edit Selected Gw Trunk Group window is displayed below.
All - Address Context - Zone - Gw Trunk Group Edit Window
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
To Create Gw Trunk Group
To create a new Gw Trunk Group, click New Gw Trunk Group tab on the Gw Trunk Group List panel.
All - Address Context - Zone - Gw Trunk Group Fields
The Create New Gw Trunk Group window is displayed.
All - Address Context - Zone - Gw Trunk Group Create Window
The following fields are displayed:
Gw Sig Trunk Group Parameters
Parameter | Description |
|---|---|
| Specifies the name of the Gateway Trunk Group. |
| The administrative state of the gateway trunk group:
|
| The operational mode of the gateway trunk group:
|
| The action when putting this gateway trunk group out Of Service. This object controls whether calls are forced off or allowed to dry up upon a mode out-of-service. Select any one of the option:
|
| Dry up timeout (in minutes) when this gateway trunk group is out Of Service with dry up action. Enter a value in the range of 0-1440. Default is 5 minutes. |
| The percentage of calls to continue to send to a remote congested gateway (in MC1). Enter value in range of 0-100 percent. Default is 90 percent. |
| The percentage of calls to continue to send to a remote congested gateway (in MC2). Enter value in range of 0-100 percent. Default is 70 percent. |
| Specifies the automatic congestion control timer. Enter value in range of 0-10. Default is 0. |
Packet Outage | |
| This is the outage (in milliseconds) on a call for that call to be counted as part of the packet outage detection algorithm. Enter value in range of 0-65535 in milliseconds. Default is 6000 milliseconds. |
| The number of calls with outages required within the current interval to declare a packet outage event. Enter value in range of 0-65535. Default is 1000. |
| The amount to reduce the bandwidth limit (as a percentage of the configured limit) when a packet outage is detected. Enter value in range of 0-100 percent. Default is |
| Used to enable automatic bandwidth reduction when a packet outage is detected. Select any one of the option:
|
| The size of the packet outage detection interval in minutes. Enter value in range of 5- 1440 minutes. Default is 15 minutes. |
| Call Reservation | |
| The percent of channels reserved for inbound calls in IP gateway trunk groups. Must be 0-100, in increments of 5. Default is 0. |
| The administrative state of the packet outage:
|
| The number of priority call resources (circuits or IP calls) to be reserved for this trunk group. Must be 0-100, default is 1. |
| The number of incoming call resources (circuits or IP calls) to be reserved for this trunk group. Must be 0-128, default is 1. |
| The percentage of outgoing call resources (circuits or IP calls) to be reserved for this trunk group. This percentage is applied to the total number of circuits less the circuits reserved for incoming calls less the circuits reserved for priority calls. Must be 0-100, default is 10%. |
| SILC | |
| The Administrative state of the SILC traffic control. Select any one of the option:
|
| The percentage of calls to accept when the machine congestion level is 1. Enter value in range of 0-100 percent. Default is 75. |
| The percentage of calls to accept when the machine congestion level is 2. Enter value in range of 0-100 percent. Default is 25. |
| Media | |
| Interface group to be used for media. |
| If enabled, filter out incoming media packets which do not match the expected source IP address and UDP port. |
| Specifies whether to enable the direct-media path so that media flows directly between endpoints in the same direct-media group or not. The options are:
|
To Copy Gw Trunk Group
To copy any of the created Gw Trunk Group and to make any minor changes, click the radio button next to the specific Gw Trunk Group to highlight the row.
All - Address Context - Zone - Gw Trunk Group Highlighted
Click Copy Gw Trunk Group tab on the Gw Trunk Group List panel.
All - Address Context - Zone - Gw Trunk Group Fields
The Copy Selected Gw Trunk Group window is displayed along with the field details which can be edited.
All - Address Context - Zone - Gw Trunk Group Copy Window
Make the required changes to the required fields and click Save to save the changes. The copied Gw Trunk Group is displayed at the bottom of the original Gw Trunk Group in the Gw Trunk Group List panel.
To Delete Gw Trunk Group
To delete any of the created Gw Trunk Group, click the radio button next to the specific Gw Trunk Group which you want to delete.
All - Address Context - Zone - Gw Trunk Group Highlighted
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
All - Address Context - Zone - Gw Trunk Group Delete Confirmation
Click Yes to remove the specific Gw Trunk Group from the list.
Overview
Content Tools