Related Pages:
Overview
The Media System Configuration contains system-wide settings for the Media System, configuring the media system means setting the number of RTP/RTCP port pairs and the starting port. Other aspects of media handling, such as Media Profiles, Lists, and Media Crypto Profiles are handled in different sections of the UI and are explained on their own topic pages.
UDP ports are used for transmission of VoIP calls employing RTP protocols (RTP over UDP). The start port is the first port that can be used for a call. Calls require a pair of ports, one for the voice the other for the control information (RTP/RTCP). The number of port pairs determines the number of simultaneous IP Call Legs on the
Unable to show "metadata-from": No such page "_space_variables"
(SBC). For example; if you have 100 pairs, you can have a maximum of 100 simultaneous IP Call Legs. This does not affect the number of TDM/TDM calls.
SBC Reserved Ports
Port | Protocol | Port | Protocol |
|---|---|---|---|
1 | RAW | 500 | UDP |
22 | TCP | 514 | UDP |
| 53 | TCP | 4500 | UDP |
80 | TCP | 30000 | UDP |
161 | UDP | 30001 | UDP |
443 | TCP | 16384 to17583 | RTP/RTCP |
How Ping Affects Media
The SBC periodically (approximately every 30 seconds) pings all the media endpoints that are engaged in calls with the SBC. For local endpoints (that are on the same subnet as the SBC), this ping mechanism is used to keep the ARP cache refreshed in the SBC. If a local endpoint does not respond to the pings, and if media IP address is different than signaling IP address, the call may have audio issues.
Configuring the Media System
- In the WebUI, click the Settings tab.
In the left navigation pane, go to Media > Media System Configuration.
Media System Configuration
Media System Configuration
Port Range - Field Definitions
Start Port
Specifies the starting number for the RTP and RTCP port range.
Number of Port Pairs
The number of media port pairs used by the SBC system.
For SBC 1000/2000. Valid entry: 1 - 4800.
For SBC SWe. Valid entry: 1 - 4000.
To determine the last port number:
First Port Number + (2*Number of Port pairs) - 1.
Example:
Given: For starting port number (16384) and the number for port pairs is 600.
There are 600 pairs, meaning there are 1200 individual ports. 16384 + (1200-1) = 17583
DSCP
Specifies the DSCP value for all RTP/RTCP packets from the SBC.
This is used whenever the SBC is connected to an external gateway that handles both data and voice traffic. When large volumes of data traffic as well as all VoIP traffic flow through the same router, a policy may be created that used the DSCP value of the media packets. The policy should be structured such that VoIP media packets receive higher priority and are expedited while other packets receive a lower priority and are queued. Network administrators should ensure that the non-VOIP packets are tagged with a different DSCP value on their network. Typically, the choice of DSCP for various kinds of packet flows in the network is determined by the network administrator and is configured on all routers within that IP network.
Music on Hold - Field Definitions
Not supported by SBC SWe Lite in this release.
Music on Hold Source
Specifies the audio source. Sources can be an uploaded music file (File) or live audio sourced from an FXS port (Live). Default option is File. If you select Live, the FXS Port option is displayed.
When uploading a Music file, the maximum file sizes are as follows:
- For SBC 1000: 1MiB
- For SBC 2000: 4MiB
- For SBC SWe Lite: 1MiB
Music files must be one of the following formats:
- WAV
- PCMA (not supported in SBC SWe Lite)
- PCMU (not supported in SBC SWe Lite)
- PCM (not supported in SBC SWe Lite)
For detailed information about how to upload a Music on Hold file, see Uploading Music on Hold Files - SBC Edge or Uploading Music on Hold Files - SBC SWe Lite.
FXS Port
A list of available FSX ports from which live audio may be sourced. The FXS Port field is only visible when Live is selected from the Music on Hold Service drop down list.
Other Options - Field Definitions
Echo Canceller Type Option
Note: Field applies to SBC 1000/2000 only.
Specifies the type of Line Echo Cancellation (standard or dual filter).
The standard LEC covers 128ms tail length (echo delay) and employs a 24ms sparse (non-zero coefficients) filter. The Dual Filter (background and foreground) Line Echo Canceller (LEC) covers 128ms tail length and uses 48ms sparse foreground filter. The Dual Filter is expected to provide better performance during double talk or slow echo-path change. Selection of the Dual Filter option may result in reduced channel densities.
Warning
Sonus recommends that you not Apply any change to the Echo Canceller Type Option unless the system is idle (no calls). Applying a change while the system is not idle may result in unknown behavior.
Echo Cancel NLP Option
Note: Field applies to SBC 1000/2000 only.
Specifies the level of echo cancellation employed by the SBC Nonlinear Signal Processor.
The default value is Mild. However there are two additional levels of echo cancellation, Strong and Aggressive. As each telephony system implementation varies, their echo characteristics similarly vary. Adjust the level of echo cancellation to suit your particular deployment. Too little cancellation may result in a persistent echo, too aggressive and you may experience voice "clipping".
Send Stun Packets
Specifies whether STUN packets are generated from the SBC. The SBC sends STUN packets on the RTP and RTCP ports on all outbound IP call legs to open ports in the firewall (between the SBC and the Internet). The ability to enable/disable this option is for customers who do not have a firewall and would like a way to disable STUN packet generation. Two options are available: Enable (STUN packets are generated and sent by the SBC) or Disable (STUN packets are not generated). Default option: Enable.
Overview
Content Tools