Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel

In this section:

Table of Contents
maxLevel3

Warning

Spacevars
0company
-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

Tooltip
tipUse ESD protective device

1 Gb SFP Characteristics

The 

Spacevars
0model5
supports the following Small Form-factor Pluggable (SFP) transceivers in all Media and HA ports. SFPs are Customer Replaceable Units (CRUs).

Div
classpdf6pttext

Caption
0Table
11Gb SFP Parts
31Gb SFP Parts
Transceiver TypeProduct CodeSFP TypeManufacturers  Part NumberWavelength  (nm)Tx Power (dBM)Rx Power (dBM)

Description
Multi-mode fiber

SBC‐5XXXSFPMM

 

1G Ethernet
MM

AVAGO TECHNOLOGIES AFBR‐5715PZSN1

BROADCOM AFBR‐5715PZ‐SN1

FINISAR FTLF8519P2BNL‐SS

FINISAR  FTLF8519P3BNL‐SS

850-9.5 (Min)-3 (Max)-17 (Min)0 (Max)GIG-E, MULTIMODE, FIBER OPTIC TRANCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 300M
Single-mode fiber

SBC‐5XXXSFPSM

 

1G Ethernet  SM
  • AVAGO TECHNOLOGIES AFCT‐5715PZSN1
  • BROADCOM AFCT‐5715PZSN1
  • FINISAR FTLF1318P2BTL‐SS
  • FINISAR FTLF1318P3BTL‐SS
1310-9.5 (Min)-3 (Max)-19 (Min)-3 (Max)

GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 10KM 1310NM, DMI

Copper SBC-5XXX-SFPCOPPER1G Ethernet Copper
  • AVAGO TECHNOLOGIES ABCU-5740RZ-SN1
  • BROADCOM ABCU-5740RZ-SN1
  • FINISAR FCLF8521P2BTL-SS
NANANANANAGIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP)

Info
titleNote

These numbers are taken from Vendor Datasheets as well as IEEE 802.3ae for the 1G parts.

 

10 Gb SFP Characteristics

Optionally, Pkt0 and Pkt1 (Media 0 and Media2) can be used as 10Gb ports, with the remaining MEDIA ports empty. The parts for the 10Gb SFPs are:

Div
classpdf6pttext

Caption
0Table
110Gb SFP Parts
310Gb SFP Parts
Transceiver TypeProduct CodeSFP TypeManufacturers  Part NumberWavelength  (nm)Tx Power (dBM)Rx Power (dBM)

Description
Multi-mode fiber

SBC‐SFPMM‐10G

10G Ethernet
MM

  • AVAGO TECHNOLOGIES AFBR‐709SMZSN1
  • BROADCOM AFBR‐709SMZ‐SN1
  • FINISAR FTLX8571D3BCL‐SS
  • FINISARFTLX8574D3BCL‐SS
850-7.9 (Min)-1 (Max)-11.1 (Min)0.5 (Max)

10.3 GB/S, MULTIMODE, FIBER OPTIC XCVR, LC, SFP, 300M 850NM, DMI GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE

Single-mode fiber

SBC‐SFPSM‐10G

 

10G Ethernet  SM
  • AVAGO TECHNOLOGIES AFCT‐709SMZSN1
  • AVAGO TECHNOLOGIES AFCT739SMZ‐SN1
  • BROADCOM AFCT‐709SMZSN1
  • BROADCOM AFCT‐739SMZ‐SN1
  • FINISAR FTLX1471D3BCL‐SS
1310-8.2 (Min)0.5 (Max)-12.6 (Min)0.5 (Max)10.3 GB/S, SINGLE MODE, FIBER OPTIC XCVR, LC, SFP, 10KM 1310NM, DM

Info
titleNote

These numbers are taken from Vendor Datasheets as well as IEEE 802.3ae for the 10G parts.

 

To replace SFPs, use the procedures from the section Replacing the SFP.

Caption
0Figure
1SFP Ports

Parts and Tools Required

  • Electrostatic discharge (ESD) strap
  • Replacement SFP transceivers
Info
titleNote

To prevent damage from electrostatic discharge, an ESD strap is provided in the accessory kit. Refer to Connecting ESD Wrist Strap to install it.

 

Anchor
ReplacingSFP
ReplacingSFP
Replacing the SFP

Perform the following procedure to replace the SFP:

  1. Attach an ESD wrist strap using the ESD grounding point on the rear panel of the chassis (refer to Connecting ESD Wrist Strap for details).
  2. Disconnect the fiber optic and/or Cat 5 cables, as appropriate, from media ports (Pkt0/1/2/3) and HA ports (HA 0-1).

  3. Disengage the SFP transceiver from

    Spacevars
    0model5
    . The method used to disengage the SFP transceiver will vary according to the manufacturer. For example, hold the wire latch and move it downwards to the horizontal position and pull it outwards, as shown below.

     

    Caption
    0Figure
    1Removing SFP

  4. Insert the

    Spacevars
    0company
    -approved SFP transceiver into the desired socket and ensure that the latch mechanism engages.

  5. Reconnect the fiber optic and/or Cat 5 cables, as appropriate, to media and HA ports.
  6. Verify LEDs above the part are flashing indicating link status and data activity.
  7. Verify port functionality using the application.

CRU Storage

Tooltip
tipESD protective device

All 

Spacevars
0model5
CRUs are shipped in electrostatic discharge bags and should be handled using appropriate ESD precautions.

The storage environment for these CRUs are:

  • Humidity must be less than 95% (non-condensing).
  • Temperature must be between -40C and +70C.

Include Page
SBXDOC121:_ESD_footnoteSBXDOC121:
_ESD_footnote

Pagebreak