Page History

Tone1 Frequency

Specifies Tone 1 Frequency in Hertz.

If 0, then silence is generated. Only valid if generation method is singleTone, dualTone, or compositeTone.

Tone1 Power

Specifies Tone 1 Power in dBm.

Power levels range from -50 dBm (minimum power) to +3 dBm (maximum power). Only valid if generation method is singleTone, dualTone, or compositeTone.

Tone1 Apply
Cadence

Specifies the cadences to which Tone 1 is applied. Application is as follows: If 0, then Tone 1 is applied to Cadences 1, 2, and 3.

If 1, then Tone 1 is applied to Cadence 1. If 2, then Tone 1 is applied to Cadence 2. If 3, then Tone 1 is applied to Cadence 3. Only valid if generation method is compositeTone.

Tone2 Frequency

Specifies Tone 2 Frequency in Hertz.

If 0, then a single frequency tone is generated. Only valid if generation method is dualTone or compositeTone.

Tone2 Power

Specifies Tone 2 Power in dBm.

Power levels range from -50 dBm (minimum power) to +3 dBm (maximum power). Only valid if generation method is dualTone or compositeTone.

Tone2 Apply
Cadence

Specifies the cadences to which Tone 2 is applied. Application is as follows: If 0, then Tone 2 is applied to Cadences 1, 2, and 3.

If 1, then Tone 2 is applied to Cadence 1. If 2, then Tone 2 is applied to Cadence 2. If 3, then Tone 2 is applied to Cadence 3. Only valid if generation method is compositeTone.

Tone3 Frequency

Specifies Tone 3 Frequency in Hertz.

If 0, then a single or dual frequency tone is generated. Only valid if generation method is compositeTone.

Tone3 Power

Specifies Tone 3 Power in dBm.

Power levels range from -50 dBm (minimum power) to +3 dBm (maximum power). Only valid if generation method is compositeTone.

Tone3 Apply
Cadence

Specifies the cadences to which Tone 3 is applied. Application is as follows: If 0, then Tone 3 is applied to Cadences 1, 2, and 3.

If 1, then Tone 3 is applied to Cadence 1. If 2, then Tone 3 is applied to Cadence 2. If 3, then Tone 3 is applied to Cadence 3. Only valid if generation method is compositeTone.

Tone4 Frequency

Specifies Tone 4 Frequency in Hertz.

If 0, then a single or dual frequency tone is generated. Only valid if generation method is compositeTone.

Tone4 Power

Specifies Tone 4 Power in dBm.

Power levels range from -50 dBm (minimum power) to +3 dBm (maximum power). Only valid if generation method is compositeTone.

Tone4 Apply
Cadence

Specifies the cadences to which Tone 1 is applied. Application is as follows: If 0, then Tone 4 is applied to Cadences 1, 2, and 3.

If 1, then Tone 4 is applied to Cadence 1. If 2, then Tone 4 is applied to Cadence 2. If 3, then Tone 4 is applied to Cadence 3. Only valid if generation method is compositeTone.

Decay Time
Constant

Specifies exponential decay time constant in milliseconds.

If 0, then no decay is applied. Maximum value is 2000 msec. Only valid if generation method is compositeTone.

Decay Frequency Delta

Specifies rate of change (Hz/s) of the tone frequency.

If 0, then no frequency change rate is applied. Only valid if generation method is compositeTone.

Decay Apply
Tone Bit Map

Specifies the tones to which decay and frequency rate change are applied. Application is by bitmap:

• If 0, then decay/frequency rate change is not applied to any tone. If 1, then decay/frequency rate change is applied to tone 1.
• If 2, then decay/frequency rate change is applied to tone 2.
• If 3, then decay/frequency rate change is applied to tones 1 and 2.
• If 4, then decay/frequency rate change is applied to tones 3 and so on.. If 15, then decay/frequency rate change is applied to tones 1, 2, and 3. Only valid if generation method is compositeTone.