Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7f046c, userName='null'}
JIRAIDAUTHSBX-88903
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c8c30172, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c8c30172, userName='null'}


Panel

In this section:

Table of Contents
maxLevel3



Info
iconfalse

Related articles:



 

The Policy Server object allows you to configure up to 10 policy servers (one local server and nine external policy servers). When an active server becomes congested, the 

Spacevars
0series4
application will first distribute overflow traffic to one of the active servers with enough capacity, or to one of the standby servers that is not currently congested.

The 

Spacevars
0product
can obtain policy services from one or more active servers in load-sharing (or round-robin) mode, and one or more active servers can be configured in the standby mode.

Types of policy server configurations include:

  • Global Configuration is applicable to all policy servers.
  • Local Policy Server Configuration is applicable to local (embedded) policy server.
  • Remote Policy Server Configuration is applicable to remote policy servers.

The 

Spacevars
0product
administrator enables or disables the policy server. When a policy server is enabled, it receives database queries from the
Spacevars
0product
. You can enable or disable the policy server only in the out-of-service mode.

Global Configuration

The Policy Server global configuration commands are described below. The

Spacevars
0product
can be configured to communicate with an external PSX policy server using either a Management Interface Group or IP Interface Group.

Info
titleNote

The

Spacevars
0product2
supports configuring an alternate IP address for communicating with the external PSX. Refer to Using an Alternate IP Address to Communicate with the PSX for details.


Info
titleNote

 The DNS query to an Interface Group outside the address context feature adds additional flexibility to query the PSX FQDN with a particular DNS Group. For more information, refer to DNS Support.

Command Syntax

Code Block
languagenone
% set system policyServer globalConfig 
	addressContext <address context name>
	congestionControl <disabled | enabled>
	dnsGroup <DNS group server name>
	dscpProfile <dscpProfileName>
	ipInterfaceGroup <ipInterfaceGroup_name>
	ipVar <metavariable name> 
	mgmtInterfaceGroup <mgmtInterfaceGroup_name>
	reconnectTimeout <1-3600 seconds> 
    sbcGatewayName <SbcGateway Name>	
    switchOverMode <automatic | manual>
	type <ip | mgmt>

Command Parameters

Caption
0Table
1Policy Server Parameters


Parameter

Length/Range

Description

addressContext1-23

<address context name> – The address context for the policy Server IP Interface Group.

NOTE: This parameter is only configurable (visible from command line) when attribute type is set to "ip".

congestionControl

N/A

When this parameter is enabled, the 

Spacevars
0product
throttles the sending or policy requests to either active or standby policy server. Options are:

  • enabled
  • disabled (default)
dnsGroupN/A<DNS group name> – The name of the DNS group to associate with the policy server global configuration to allow PSX FQDN resolution with a particular DNS group.
dscpProfile
 

<profile_name> - Name of the DSCP Profile in which DSCP values are configured for HPC and non HPC calls. For more information, refer to DSCP Profile - CLI.
ipInterfaceGroup 1-23

<IPIG name> – The IP Interface Group belonging to the configured address context. This IP Interface Group is used for communicating with the external PSX.

NOTE: This parameter is only configurable once addressContext is set.

ipVar1-255

Use this parameter to specify a metavariable name (from the PSX’s metavariable table) used to provide an IP address for the

Spacevars
0product2
for connecting to the PSX. When the ipVar field is blank, the
Spacevars
0product2
picks any random IP address from the configured interface to connect to the PSX.

NOTE: Use this parameter for

Spacevars
0product2
N:1 HA or cloud-based deployments only.

mgmtInterfaceGroup

N/A

Specifies the Management Interface Group to be used for communication with an external PSX.

NOTE: If attribute type is set to "ip", this parameter is no longer configurable.

reconnectTimeout

1-3600

Specifies the timeout period in seconds to re-attempt the connection to a policy server that is in the enabled state. Default is 10 seconds.

sbcGatewayNameN/AThe SBC Gateway name given to the softswitch.

switchOverMode

N/A

Specifies the mode to switch over the policy server to active state. Mode can be:

  • automatic (default) – in this state the policy server automatically retries to the previously ACTIVE policy server after a switch-over.
  • manual – In this state you have to manually set the policy server to ACTIVE state after a switch-over.
typeN/A

Interface type supported by the policy server.

  • ip – IP Interface
  • mgmt – Management Interface
 



Command Examples

To set the policy server global configuration using management interface group called "mgmtGroup":

Code Block
languagenone
% set system policyServer globalConfig type mgmt mgmtInterfaceGroup mgmtGroup congestionControl enabled reconnectTimeout 5 switchOverMode automatic

 


To set the policy server global configuration using IP Interface Group called "ipInterfaceGroup":

Code Block
% set system policyServer remoteServer PSXSWE2 state disabled mode outOfService
% commit


Code Block
% set system policyServer globalConfig type ip addressContext a1 ipInterfaceGroup LIF1 reconnectTimeout 10 switchOverMode automatic congestionControl enabled
% commit


Code Block
% set system policyServer remoteServer PSXSWE2 state enabled mode active
% commit
 

To view the policy server global configuration settings with type as mgmt:
 Code Block
languagenone
% show system policyServer globalConfig
reconnectTimeout   5;
switchOverMode     automatic;
congestionControl  enabled;
type               mgmt;
mgmtInterfaceGroup mgmtGroup;
 

To view the policy server global configuration settings with type as ip:
 Code Block
> show system policyServer globalConfig
reconnectTimeout 10;
switchOverMode automatic;
congestionControl disabled;
type ip;
addressContext a1;
ipInterfaceGroup LIF1;
 

To view the status of policy server global configuration from system-level mode with type as mgmt:
 Code Block
languagenone
> show table system policyServer globalConfig
reconnectTimeout   5;
switchOverMode     automatic;
congestionControl  enabled;
type               mgmt;
mgmtInterfaceGroup mgmtGroup;
 

To view the status of policy server global configuration from system-level mode with type as ip:
 Code Block
> show table system policyServer globalConfig
reconnectTimeout 10;
switchOverMode automatic;
congestionControl disabled;
type ip;
addressContext a1;
ipInterfaceGroup LIF1;
 

Local Policy Server Configuration
The Local Policy Server configuration commands are described below.
Command Syntax
 Code Block
languagenone
% set system policyServer localServer <softswitch_name>
	action <dryUp | force>
	keepAliveTimer <1-60 seconds>
	mode <active | alternate | outOfService | standby>
	retries <0-32>
	retryTimer <# milliseconds>
	state <disabled | enabled>
	transactionTimer <50-60000 milliseconds>
Command Parameters
 
 Caption
0Table
1Command parameters


Parameter
Length/Range
Description
localServer
N/A
Specifies the name of the local policy server.
action
N/A
Specifies the method on which queued transactions are processed, when operational state is either standby or out-of-service: 
• dryup (default) — all queue entries are processed to completion unless retries expires. 
• force — all queue transactions are dropped immediately.
keepAliveTimer
1-60
Specifies the time interval (in seconds) to wait before issuing a "keepalive" poll to the policy server. This poll is issued only if there is no other policy server activity during this interval. The receipt of any message from the policy server resets the elapsed time to 0. 
Must be 1-60, default is 5.
mode
N/A
Specifies the operational state of the local policy server:
  • outofservice – The local policy server is out-of-service and will not provide any services.
  • active – The local policy server provides normal query services.
  • standby – The local policy server serves as a backup when another server in the active mode becomes unavailable.
  • alternate – The local policy server is not expected to receive any query messages, but can send messages to SBC. 
NOTE: If two external active policy servers fail and local policy server is in standby mode, the standby local policy server is used as active server until the external policy server becomes active.
retries
0-32
Specifies the number of retries for any policy server transaction. Must be 0-32, default is 1.
retryTimer
N/A
Specifies the time (in milliseconds) for the 
 Spacevars
0product
 to wait for the response from the local policy server. (default = 2500).
state
N/A
The administrative state of the local policy server.
  • disabled – The local policy server is not used for call routing decisions.
  • enabled – The local policy server is used for call routing decisions.
NOTE: If changing the state, ensure mode is first set to "outofservice".
transactionTimer
50-60000
Time to wait (in milliseconds) for a reply from the initial transaction request. When this timer expires, a transaction retry will be issued. Subsequent retries of this transaction are controlled by retries. (Default = 2500)
Command Example
To set the local policy server configuration:
 Code Block
languagenone
% set system policyServer localServer PSX_LOCAL_SERVER action dryUp keepAliveTimer 3 mode standby retries 1 retryTimer 2500 state enabled transactionTimer 2500
 

To view the local policy server configuration settings:
 Code Block
languagenone
% show system policyServer localServer  
localServer PSX_LOCAL_SERVER {  
	state enabled;  
	mode standby;  
	action dryUp;  
	transactionTimer 2500;  
	keepAliveTimer 3;  
	retryTimer 2500;  
	retries 1;  
}
 

To view the status of local policy servers:
 Code Block
languagenone
 % show table system policyServer localServer
								KEEP 
						TRANSACTION 	ALIVE 	RETRY 
NAME 			STATE 	MODE 	ACTION 	TIMER 		TIMER 	TIMER RETRIES 
------------------------------------------------------------------------------- 
PSX_LOCAL_SERVER 	enabled active  dryUp 	2500 		5 	2500 	1
Remote Policy Server Configuration
The Remote Policy Server configuration commands are described below.
Command Syntax
 Code Block
languagenone
% set system policyServer remoteServer <softswitch_name>
	action <dryUp | force>
	ipAddress 169.254.77.2
	keepAliveTimer <1-60 seconds>
	mode <active | alternate | outOfService | standby>
	portNumber <softswitch port number>
	retries <0-32>
	retryTimer <# milliseconds>
	state <disabled | enabled>
	subPortNumber <port number for subscriber data>
	transactionTimer <50-60000 milliseconds>
 
% request system policyServer remoteServer <softswitch_name> switchBack
Command Parameters
 Caption
0Table
1Command parameters
 


Parameter
Length/Range
Description
remoteServer
N/A
The name of the remote policy server.
action
N/A
Use this object to specify the action to take against the policy server.
  • dryup (default) – All queued transactions are processed to completion unless retries expire.
  • force – All queued transactions are dropped immediately.
ipAddress
N/A
the IP address.
keepAliveTimer
1-60
The time interval (in seconds) to wait before issuing a "keepalive" poll to the policy server. This poll is issued only if there is no other policy server activity during this interval. The receipt of any message from the policy server resets the elapsed time to 0 (default = 5).
mode
N/A
The operational state of the remote policy server:
  • outofservice – The remote policy server is out-of-service and will not provide any services to the 
     Spacevars
    0product
    .
  • active – The remote policy server provides normal query services.
  • standby – The remote policy server serves as a backup when another server in the active mode becomes unavailable.
  • alternate – The remote policy server is not expected to receive any query messages from the 
     Spacevars
    0product
    , but can send messages to 
     Spacevars
    0product
    .
portNumber
1-65535
The logical port number used for IP communication with the remote policy server. (default = 3055).
retries
0-32
The number of times to retry any remote policy server transaction. (default = 1).
retryTimer
N/A
The time (in milliseconds) for the 
 Spacevars
0product
 to wait for the response from the remote policy server. (default = 2500).
state
N/A
Administrative state of the remote policy server. Options are:
  • disabled (default) – The remote policy server is not used for call routing decisions.
  • enabled – The remote policy server is used for call routing decisions. 
NOTE: The mode must be set to 'outOfService' before changing the state.
subPortNumber
1-65535
The port number assigned for the IP address of the policy server for the specific purpose of communicating subscriber data. (default = 3053).
switchback
N/A
Use this parameter with the request command to force a previously active (now standby) PSX to revert back to an active state.  Note that the switchOverMode parameter in globalConfig must be set to manual.
transactionTimer
50-60000
The time for 
 Spacevars
0product
 to wait (in milliseconds) for a reply from the policy server after sending a transaction request. When this timer expires, a transaction retry is issued based on retries setting. (default = 2500).
Command Examples
To set the remote policy server configuration:
 Code Block
languagenone
% set system policyServer remoteServer RS-1 mode outOfService  
% set system policyServer remoteServer RS-1 ipAddress 169.254.77.2 state enabled
 

To view the remote policy server configuration settings:
 Code Block
languagenone
% show system policyServer remoteServer  
remoteServer RS-1 {  
	ipAddress 169.254.77.2;  
	state enabled;  
	mode outOfService;  
} 
 

To view the status of remote policy server from top-level CLI mode:
 Code Block
languagenone
> show table system policyServer remoteServer  
                                                                KEEP                   SUB
      IP            PORT                           TRANSACTION  ALIVE  RETRY           PORT
NAME  ADDRESS       NUMBER  STATE   MODE   ACTION  TIMER        TIMER  TIMER  RETRIES  NUMBER
--------------------------------------------------------------------------------------------
RS-1  169.254.77.2  3055    enabled active dryUp   2500 	       5 	  2500 	 1 
3053 

 To reset the SIP registration count of the remote policy server:
 Code Block
languagenone
% request system policyServerremoteServer RS-1 switchBack  
result PASSED

 Info
titleNote
In order to use the 'switchBack' command, the remote policy server must first be configured to allow a manual switchback.
 

 Pagebreak