Versions Compared

Old Version 3

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7f046c, userName='null'}
JIRAIDAUTHSBX-96078
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7d045b, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cdcd0ab1, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd880a41, userName='null'}
REV2UserResourceIdentifier{userKey=8a00a0c86573c0900165a3a88335002a, userName='null'}

Include Page
_EMS in EMA, CLI, API
_EMS in EMA, CLI, API


Panel

In this section:

Table of Contents



Info
iconfalse

Related articles:


Overview

Use this section to configure EMA components using CLI.

To disable/enable EMA components from the CLI, the following enhancements are available:

  • The parameter ema is added under system admin. The child parameters of ema, each with the disable/enable options, are as follows:
    • enableCoreEMA
    • enableREST
    • enableTS
  • To display the status of the EMA components, the parameter ema, with its child parameters, are available under system admin of the show commands.

Command Syntax

To disable/enable the EMA components, use the following syntax:

Code Block
% set system admin <system_name>
  ema
    enableCoreEMA <disabled | enabled>
    enableREST <disabled | enabled>
    enableTS <disabled | enabled>


To display the status of the EMA components, use the following syntax:

  • Within the "configure" mode:

    Code Block
    % show system admin <system_name> ema <enableCoreEMA | enableREST | enableTS>


  • Outside of the "configure" mode:

    Code Block
    > show table system admin <system_name> ema <enableCoreEMA | enableREST | enableTS>


Info
titleNote

If you do not provide the name of the EMA component, the output displays the status of all the three components.

Command Parameters

Caption
0Table
1Parameter Description Table


ParameterLength/RangeDescriptionM/O
emaN/AThe object encapsulating the three EMA components.O
enableCoreEMA
N/A

Use this parameter to disable or enable the Core EMA component.

  • disabled
  • enabled (default)
O
enableREST
N/A

Use this parameter to disable or enable the

Spacevars
0model1
services provided by the EMA for SBC configuration (using the SBC Manager of the
Spacevars
0model3
).

  • disabled
  • enabled (default)
O
enableTS
N/A

Use this parameter to disable or enable the Troubleshooting component of the EMA.

  • disabled
  • enabled (default)
O


Configuration Examples

Tip
titleTip

The SBC is enhanced to enable/disable these components independently; the state of one component does not affect the function of the other components. For using the full capabilities of the EMA, Ribbon recommends enabling all the components simultaneously.

You can disable/enable the components during installation, or after the installation. By default, all the components are enabled. For the post-installation changes to take effect, restart the application.


To configure the EMA components, use the following example:

Code Block
% set system admin REDGRAPE-SA ema enableCoreEMA enabled enableREST disabled enableTS enabled


To display the status of the EMA components, use the following example:

  • Within "configure" mode:

    Code Block
    % show system admin REDGRAPE-SA ema
enableREST    enabled;
enableCoreEMA enabled;
enableTS      enabled;
[ok][<YYYY-MM-DD HH:MM:SS>]


  • Outside "configure" mode:

    Code Block
    > show table system admin REDGRAPE-SA ema
enableREST    enabled;
enableCoreEMA enabled;
enableTS      enabled;
[ok][<YYYY-MM-DD HH:MM:SS>]