Page History
Add_workflow_for_techpubs | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
|
To install and configure
Spacevars | ||
---|---|---|
|
Download the
artifacts, install-ev.sh and , ev-fullpkg.tar.xz to , and MD5SUM.txt to the /opt directory of your system.Spacevars 0 product Info title Note For these artifacts, log in to Salesforce and open an additional browser for the Ribbon Global Software Center (GSC). In the Downloads section, search for the name and version of the required software.
To download a software package from the Ribbon Support Portal, see Ribbon Support Portal - Download Center.
Enable read-write-execute permissions for the copied files using the command given below:
Code Block chmod +x install-ev.sh
Validate installation media readiness using the command given below:
Code Block pwd && ls -alh
As depicted in the example screenshot, confirm the two files exhibit approximately the same size and permissions.Execute the following command to start installation process:
The installation continues by installing Docker Compose, Docker andCode Block ./install-ev.sh
Info title Note Beginning with Release 16.4.4, using the install-ev.sh script to install Docker and Docker Compose is not supported. Hence, customers must set up Docker before installing or upgrading the
to Release 16.4.4.Spacevars 0 product
As the
installation continues, set the . The GUI_IP, EV_IP, and EV_IP6 values should be set , so that theSpacevars 0 product
works properly works correctly. Respond to any prompts that arise, especially the GUI_IP, EV_IP, and EV_IP6 prompt prompts, which is are critical to the installation. GUI_IP, EV_IP, and EV_IP6 values must be set so thatSpacevars 0 product
works properly.Spacevars 0 product GUI_IP - The host name or address that the users can use to access
from the browser's address bar.Spacevars 0 product Info title Note GUI_IP must be the same as either EV_IP or EV_IP6.
EV_IP - The host name or IPv4 address for the managed devices to contact
.Spacevars 0 product EV_IP6 - The host name or IPv6 address for managed devices to contact
.Spacevars 0 product Info title Note The EV_IP6 address is not set by default. If you want to access
using IPv6 modify the current settings and provide the EV_IP6 address.Spacevars 0 product
The installation creates a log file of all actions for historical review/troubleshooting. The resultant filename is in the format of $MM-DD-YYYY-ev-install.log
You are prompted to enter information related to your networking configuration. Read this section carefully and enter the appropriate values applicable to your environment.
Once installation completes, the console screen displays the message “
Installation/Upgrade Completed ”. A directory named scc-build is created.Spacevars 0 product To check whether the containers started successfully, use the following command:
Code Block docker ps --format "table {{.ID}}\t{{.Image}}\t{{.Status}}\t{{.Names}}"
Tip title Tip Make sure that the STATUS is healthy. If there are unhealthy statuses, run the following command and check the Health section of the output:
Code Block docker inspect $container_name
For example:
Code Block docker inspect scc
Once the installation completes, optionally run a basic sanity check using the command given below:s
Code Block cd /opt/scc-build ; ./ev_check.sh post-install
For initial SCC configuration, register your
server by accessing it through the web interface at its IP address and entering the registration information that you received in your email. If the registration information is not available, reach out to Ribbon Support.Spacevars 0 product Info title Note Refer to Manually Configure ZTP when upgrading from
15.2.0 or 15.2.1.Spacevars 0 product - Enter the
admin registration details, and then click NEXT.Spacevars 0 product - Enter the Tenant Admin registration details, and then click NEXT.
- Click APPLY to complete the registration.
- Click LOGIN to navigate to the login screen.
- Enter the credentials and click SIGN IN to log in to
.Spacevars 0 product
...