Table of Contents
maxLevel 1

Status Panel LEDs

...

Panel

...

Spacevars
0 longproduct

...

Caption
0 Figure 1 Status Panel LEDs
Image Removed

...

1. Power Status LED

This status LED indicates the power conditions of the

Spacevars
0 longproduct

system. The normal state of this LED is on and green.

...

System is connected to proper power source.

...

2. Alarms Status LED

This status LED indicates the alarm state of the 

Spacevars
0 longproduct

system. The normal state of this LED is green, indicating there is no alarm.

For detailed information about alarm types, see Alarms and Events Reference.

...

Critical alarm.

3. Peer Node Status LED (Locator LED)

Tip
The Peer Node Status LED is also recognized as the Locator LED when configuring this option in the WEB GUI.

This status LED is green when the 

Spacevars
0 longproduct

system is fully powered up. It is also used as a system locator LED for the SBC unit (the green blinking light helps network personnel easily locate the SBC in a rack with other equipment). Through the WEBUI, this LED can be turned off or made to blink once per second. See Configuring Host Information and DNS.

...

In this section: Table of Contents maxLevel 4 minLevel 2

4. Ready Status LED

This status LED indicates if the 

Spacevars
0 longproduct

system is properly initialized. The normal state of this LED is on and green.

...

Ethernet Port Status LEDs

This section describes the Ethernet Port Status LEDs located in the right and left corners of the Ethernet ports. See below for LED ranges.

Caption
0 Figure 1 Ethernet Port Status LEDs
Image Removed

...

1. Ethernet Port Status LED

Tip
The Ethernet LEDs displayed represent a Spacevars 0 series ; the Ethernet LEDs function is the same for the Spacevars 0 series2 .

This Ethernet Port Status LEDs indicate the status conditions of the Ethernet ports on the 

Spacevars
0 longproduct

system.

...

Left-Side LED

...

Right-Side LED

...

Right/Left LED Combinations

...

Pagebreak

...

Status Panel LEDs

This section describes the Status LEDs located on the front panel of the

Spacevars
0 longproduct

chassis. Overall, when all four Status LEDs are lit green, the system is powered up and is in good operating condition. See below for individual LED ranges. For more information about the error states of these LEDs, see Status Panel States and Actions.

Section

Caption 0 Figure 1 Status Panel LEDs Image Modified Anchor power power 1. Power Status LED This status LED indicates the power conditions of the Spacevars 0 longproduct system. The normal state of this LED is on and green. Anchor alarms alarms Color Status Green System is connected to proper power source. Off System is not connected to power source. 2. Alarms Status LED This status LED indicates the alarm state of the  Spacevars 0 longproduct system. The normal state of this LED is green, indicating there is no alarm. For detailed information about alarm types, see Alarms and Events Reference. Anchor peer-node peer-node Color  Status Green No alarm. Off Warning (indicates the lowest severity level of an alarm has occurred).  Amber Minor alarm. Red Major alarm. Red Blinking Critical alarm. 3. Peer Node Status LED (Locator LED) Tip The Peer Node Status LED is also recognized as the Locator LED when configuring this option in the WEB GUI.  This status LED is green when the  Spacevars 0 longproduct system is fully powered up. It is also used as a system locator LED for the SBC unit (the green blinking light helps network personnel easily locate the SBC in a rack with other equipment). Through the WEBUI, this LED can be turned off or made to blink once per second. See Configuring Host Information and DNS. Anchor ready ready Color Status Green System is fully powered up. Off User Enabled option. LED is turned off through the LED Locator configuration option. See Configuring Host Information and DNS. Blinking Green User Enabled option. LED is turned to blinking green through the LED Locator configuration option. Light will blink once per second. See Configuring Host Information and DNS. 4. Ready Status LED This status LED indicates if the  Spacevars 0 longproduct system is properly initialized. The normal state of this LED is on and green. Color Status Green System is properly initialized. Off System is not properly initialized.

Section

Ethernet Port Status LEDs This section describes the Ethernet Port Status LEDs located in the right and left corners of the Ethernet ports. See below for LED ranges. Caption 0 Figure 1 Ethernet Port Status LEDs Image Modified Anchor power power 1. Ethernet Port Status LED Tip The Ethernet LEDs displayed represent a Spacevars 0 series ; the Ethernet LEDs function is the same for the Spacevars 0 series2 . This Ethernet Port Status LEDs indicate the status conditions of the Ethernet ports on the  Spacevars 0 longproduct system. Anchor alarms alarms Left-Side LED Color  Status Amber Indicates Ethernet port speed at 10/100Mbps. Off Indicates Ethernet port speed at 1000Mbps.  Right-Side LED Color Status Green Ethernet link is established. Flashing Green Ethernet link is active. Data is being sent/received. Off Ethernet link is down. Right/Left LED Combinations Left-Side Color Right-Side Color Result Amber Off Port speed is 10Mbpbs. Ethernet link is down. Amber Green Port speed is 100Mbps. Ethernet link is established. Off Green Port speed is 1000Mbps. Ethernet link is established.

...