Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a0c86e9b2550016ec54396b5000a, userName='null'}
JIRAIDAUTHSBX-110943
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cbfd06fb, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cbfd06fb, userName='null'}

Include Page
_Clear_upgrade_directory_warning
_Clear_upgrade_directory_warning

Info
titleNote

To recover from the default indices, refer to MOP to Recover from Mismatch in 1:1 SBC SWe HA Session Estimates, if applicable.

This section describes the different methods to upgrade the 

Spacevars
0series4
(SBC 5000 series, SBC 7000 series and SBC SWe) application.

When an 

Spacevars
0product
 upgrade is available, the software is posted on the Ribbon Support Portal. Refer to Downloading Software from the Ribbon Support Portal for more information.


Prerequisities

Prior to performing an upgrade on the

Spacevars
0series4
, ensure the following activies are accomplished.

For 

Spacevars
0series4
 (in general):

  • Before upgrading the ConnexIP OS, firmware, and the 
    Spacevars
    0product
    application, you must first save the configuration in case you encounter any issues during the upgrade.
  • Before upgrading the application, upgrade the SBC firmware to the latest version on both the active and standby SBCs for an HA pair.

For 

Spacevars
0product2
:

  • Increase the memory to the larger of:

    • the minimum memory required for the release.
      or
    • the memory required for the desired session capacity.
    Info
    titleNote

    The performance/capacity of the 

    Spacevars
    0product2

     instances configured with only 12 GB of RAM have lower capacity limits than instances with higher memory configurations, thus they may not perform at optimum capacity. Contact your Ribbon representative to order DIMM kits to increase the RAM to 24 GB.For
    Spacevars
    0product2

    is impacted by the amount of memory assigned to the VM. Review SBC SWe Performance Metrics to see the memory requirements for the current release

    , and

    plus a procedure to upgrade memory,

    refer to SBC SWe Performance Metrics.

    if required. Complete the procedure to upgrade memory prior to performing the upgrade.


  • Ensure the
    Spacevars
    0product2
     memory reservation meets the requirements for the current release. Refer to SBC SWe Performance Metrics.

Multiexcerpt include
MultiExcerptNamedisk_space_requirement
PageWithExcerpt_Disk_Space_Requirement_SWe_Cloud_Upgrades

Live Software Upgrade (LSWU)

LSWU allows a user to upgrade the

Spacevars
0product
 application software on HA pairs without impacting service (dropping calls). This is mainly recommended for HA SBC systems. You can also perform a LSWU on the 
Spacevars
0product
 EMA and in 
Spacevars
0product
 EMA Platform Mode. Refer to Live Software Upgrade using CLI and System Administration - Software Install-Upgrade for more information.

Non-Live Software Upgrade (Non-LSWU)

The non-LSWU upgrade process requires taking the SBC system offline to perform an application upgrade. This refers to upgrading the

Spacevars
0product
 application in a standalone or HA configuration using EMA Platform Mode. Refer to Upgrading SBC Application using EMA Platform Mode for more information.


Info
titleNote

Once the upgrade is complete, rediscover the SBC from the EMS, if present, and edit any attributes that may have been modified post-upgrade. Attributes are listed under the EMS page Register an SBC Core Node.


Pagebreak