Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a0c87a8bc654017a90dcbbab0002, userName='null'}
JIRAIDAUTHEMTP-26924640
REV5UserResourceIdentifier{userKey=8a00a0c85f4199b1015f7ea6e836000d, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a0c85f4199b1015f7ea6e836000d, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a0c8601a1bc701602339d1190006, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a0c86d32712b016d406f77af0008, userName='null'}
REV2UserResourceIdentifier{userKey=8a00a0c8652ba79201656dbe5f14001b, userName='null'}

  1. Choose VoIP > SIP >SIP UA > Advanced.

  2. Scroll to Port Level Advanced Configuration.


  3. Configure settings using the information in the following table as a guide.

    Caption
    0Table
    1FXS/Phone Port Settings - Advanced


    ItemDescription

    Port Level Advanced Configuration

    Configures parameters for each port.

    Port 1 Configuration

    Codec Preference

    Select a codec from the drop down list if a setting other than the globally configured one is desired. This may be useful for cases such as when a fax machine is connected to the port.

    When making or receiving a call, if that codec is part of the negotiated codec list, then that codec is used to encode and send voice packets. Select the Global setting to use the Global codec preference at port level (default).

    Use preferred codec only

    Select the Use preferred codec only checkbox to specify that only the preferred codec is used when the FXS places a call. If an incoming call does not have the preferred codec, the call is rejected.

    This setting does not apply if the preferred codec is set to Global Setting.

    DomainEnter a domain in this field to use a value other than the domain configured on the main SIP configuration page.

    Outbound Proxy Server IP

    		Enter the IP address of the outbound proxy server to have calls from this FXS port to use a server other than what is configured under SIP configuration.

    Outbound Proxy Server Port

    Enter the outbound proxy server port that SIP UA uses to register each FXS port and make outbound calls. Each FXS port can use different outgoing proxy and domain for SIP signaling. This field is blank by default to use global configuration.

    If VoIP-ALG is enabled, the outbound proxy must point to the VOIP ALG LAN interface.

    TX gain to analog device

    Choose the analog transmit gain for the FXS port. The default setting of 0dB is appropriate for most installations; however, you can adjust the setting to interoperate with user endpoints such as phones, fax, or key systems. Range is -16dB to 16dB, default is 0dB.

    RX gain from analog device

    Choose the analog receive gain for the FXS port. The default setting of 0dB is appropriate for most installations; however, you can adjust the setting to interoperate with user endpoints such as phones, fax, or key systems. Range is -16dB to 16dB, default is 0dB.

    Member of Hunt Group

    Select the Member of Hunt Group checkbox to enable the associated FXS port to answer incoming calls that are placed to the hunt group from an IP network. If When enabled, FXS port is put in a hunt group for answering Incoming calls from IP network. If a call comes directly to a port in group, that port answers the call. If the port is busy or the call has comes come to a hunt group DID, by default, ports in the group are picked up using the lowest free port number in the configuration order. If the first port in the group is busy, second free port in the group is picked up and so on. To use a round-robin scheme to pick up, from first port in the group to port N in the groupgroup, define SIPUA_HUNT_CIRCULAR in the configuration. When no FXS port is free in the pool to receive the call, a “486 Busy” is sent. A single hunt group is supported on an EdgeMarc. See also Serial Hunt in B2BUA configuration for additional options486 Busy is sent.

    Info
    titleNote

    “Define SIPUA_HUNT_CIRCULAR” means configure the line SIPUA_HUNT_CIRCULAR=on in /etc/config/sipua_defs.conf. By default this parameter is set to off.


    Enable Call Waiting

    		Select the Enable Call Waiting checkbox to enable call waiting at the port level. If call waiting is enabled globally, it is enabled at port level as well. Call waiting can be disabled globally and enabled at port level.

    Enable Call Waiting CallerID

    Select the Enable Call Waiting CallerID checkbox to enable call-waiting caller-ID feature at port level. If feature is enabled globally, it is enabled at port level as well. However this feature can be disabled globally and enabled at port level.

    VAD Enable

    Choose voice activity detection for the FXS port:

    • On

    • Off

    • Global Setting—Allows global VAD settings to be applied at the port level.

    Hotline Number

    Enter the number that a port calls automatically when it goes off-hook. If the field is empty, the feature is disabled.

    Restrict CallerID

    Select the Restrict CallerID checkbox to enable endpoint call privacy - user provisioned on the port - in a trusted SIP network (RFC 3325). Caller Identity in From SIP header is restricted and is instead carried in P-Preferred-Identity SIP header. If the endpoint does not trust the proxy that it sends request to, leave the box un-checked.

    Disable Flash Hook

    Select the Disable Flash Hook checkbox and click Submit to disable Flash Hook on SIPUA FXS Ports.



  4. Click Submit at the bottom of the page to save your changes or click Reset to Defaults at the top of the page.